Table of Contents
Advertisement
12. SETUP MENU
12-1 VCR Setup Menu (Cont'd)
VCR SETUP MENU CONTENTS
Group
Upper row: Viewfinder display
Lower row: Counter display indication
SERVO
050: REMOTE SELECT
/SYSTEM
rnSL
Note:
• The operation buttons on the GY-DV700W remain effective even when set to IEEE1394 or RS232C.
• When the REMOTE SELECT item is set to IEEE1394 or RS232C, ASPECT RATIO will be fixed and "FIX" is displayed.
052: STEP SLOW
MODE
StEP
082: BACK TALLY MODE
rtMd
126: INPUT SELECT
VIDEO
vid
Note:
The setting of this item can only be changed in
the stop mode or when a cassette is not loaded.
244: LOW CUT
AUDIO
LctF
245: SAMPLING RATE
snPL
Note:
The setting of this item can only be
changed in the stop mode or when a
cassette is not loaded.
246: FRONT VOLUME
ENABLE
FruL
68
Setting
Item
Value
LOCAL
IEEE1394
RS232C
Lc
iE
23
FIELD
FRAME
Fd
FM
OFF
ON
BLINK
oF
on
bL
CAMERA
IEEE1394
cA, iE
OFF
CH1
CH2
CH1 &
CH2
oF
01
02
on
32K
48K
32
48
DISABLE
ENABLE
oF
on
Contents
Selection of the method for remote control of the VCR.
LOCAL
: Choose this setting when the VCR should
be controlled using the operation buttons
on the GY-DV700W only.
IEEE1394 : Choose this setting when the VCR should
be remote controlled from a DV connector
equipped video component connected to
the DV connector on the rear section of the
GY-DV700W.
RS232C : Choose this setting for control by means of
the VCR remote control signal from the VTR
REMOTE connector on the GY-DV700W.
Selection of the advance amount in STILL mode.
(Frame/Field advance is effective only with an external
remote control signal.)
FIELD
: Field-by-field advance.
FRAME
: Frame-by-frame advance.
Selection of the lighting pattern of the BACK TALLY lamp
on the rear section during recording.
OFF
: The lamp is always off.
ON
: The lamp lights during recording. It remains
off until the VTR trigger button is pressed
to start the recording.
BLINK
: The lamp lights during recording. It blinks
when the VTR trigger button is pressed to
start the recording.
Selection of the input video signal.
Settings cannot be changed during recording.
CAMERA : Camera image is input.
IEEE1394 : The image from the DV connector equipped
video component connected to the DV con-
nector on the rear section is input.
To select whether or not the low frequencies of the
audio signal from the audio input connectors are cut.
Set to ON to reduce the wind noise of the microphone.
OFF
: The CH1 and CH2 low frequencies are not cut.
CH1
: Only the low frequencies of the audio signal
input to the CH1 channel are cut.
CH2
: Only the low frequencies of the audio signal
input to the CH2 channel are cut.
CH1& CH2 : The low frequencies are cut for both CH1
and CH2.
To select the sampling rate for digital PCM audio
recording. (Both CH1 and CH2)
32K
: Digital recording occurs with 12-bit, 32 kHz
sampling
48K
: Digital recording occurs with 16-bit 48 kHz
sampling.
* The DV format offers recording tracks for up to 4 chan-
nel when recording using 12-bit, 32 kHz sampling. The
GY-DV700W records two of these tracks. The GY-
DV700W does not allow after-recording.
To select whether or not the front section recording level
control should be operative. The front section recording
level control only affects the audio signal recorded on CH1.
DISABLE : Use of the front section recording level
control is disabled.
ENABLE : Use of the front section recording level
control is enabled.
* The CH-1 recording level control on the side section
works regardless of the setting.
Factory
Setting
LOCAL
FRAME
BLINK
CAMERA
OFF
48K
ENABLE
Advertisement
Table of Contents
