Table of Contents
Advertisement
10-5 Writing S.S.F. Data to Tape
2.
LOG button
FILTER
1 3200k
2 5600k+1/8ND
3 5600k
4 5600k+1/64ND
SHUTTER
STATUS
C
MENU
AUTO IRIS
FULL AUTO BLACK
BACK L
NORMAL
SPOT L
NG
CH-1
10-6 Outputting S.S.F. Data
The S.S.F. data in the memory of the main unit or that recorded
at the beginning of the tape can be output via the VTR REMOTE
connector using the RS-232C controller.
For how to make connections for this, refer to "Connecting to a
PC" on page 65.
Operation
In the stopped condition, the GY-DV700W answers with the
S.S.F. data when it receives the RS-232C command D5h "S.S.F.
DATA SENSE" from the PC.
(Indication example)
START
ID NO: 2c97
REEL NO: 1818
SCENE
MARK IN
MARK OUT
001M
00:00:00:16
00:00:04:19
002M
00:00:06:03
00:00:08:08
003C
00:03:15:17
00:03:57:00
004C
00:03:58:18
00:05:37:24
004C
00:03:58:18
00:05:37:24
004C
00:03:58:18
00:05:37:24
END
10. S.S.F. (Super Scene Finder) FUNCTION
LOG
REW
STOP
FF
PLAY
STILL
1.
STOP button
2.
REW button
OPERATE/WARNING
LIGHT
RESET
ON
OFF
MONITOR
SELECT
COUNTER
CTL
ALARM
TC
UB
MONITOR
AUDIO
CH-1
CH-2
LEVEL
LOLUX
STRETCH
NORMAL
COMPRESS
POWER
ON
OFF
AUDIO
CH-2
TC GENERATOR
CH-1
CH-2
LEVEL
PRESET
FREE
AUTO
REGEN
REC
MANUAL
AUDIO SELECT
AUDIO INPUT
CH-1
CH-2
CONTINUE
MENU
FRONT
REAR
LITHIUM BATT.
GROUP
ITEM
SELECT
DATA SET
HOLD
SHIFT
ADVANCE
PRESET
CONTINUE button
CUE
00:04:00:21
00:04:07:22
00:04:18:23
S.S.F. data stored in the unitís memory can be written to the
beginning of tape.
Precautions when writing S.S.F. data
• When S.S.F. data stored in the memory of the GY-
DV700W is written to the beginning of the rewound tape,
approximately 5 seconds of recorded video and/or sound
will be erased at the beginning.
In the case of important recordings, leave 5 seconds or
more of the tape unrecorded before starting recording.
• Writing of S.S.F. data should be done with the DC cable
disconnected.
Operation
1.
Press the STOP button to enter the stop mode.
2.
Press the REW button while the LOG button is kept pressed.
• The REW indicator blinks during tape transport in the
writing position.
• The LOG indicator lights while S.S.F. data are being
written to the tape.
• When writing to the tape is completed, the LOG indicator
goes out.
About the Scene End Cue Up Function
When the CONTINUE button is pressed while the LOG
button is kept pressed in the stop mode, the tape winds
to the S.S.F. data's last OUT point, after which the unit
enters the record-pause mode. (Scene End Cue Up)
The FF button's LED blinks during the Scene End Cue
Up mode.
Note:
Once a tape with recorded S.S.F. data is ejected and then
reinserted again, the previous data will be erased if new
S.S.F. data are recorded on the tape.
Operation
When recording in the S.S.F. mode is completed, and the
cassette tape has not been taken out, the S.S.F. data stored
in the memory of the GY-DV700W are output when the RS-
232C command D5h is received.
If the tape recorded in S.S.F. mode is ejected and then loaded
again, the GY-DV700W rewinds the tape to the beginning
and plays back for about 10 seconds when it receives the
RS-232C command D5h.
During the playback, the model lD data and reel number
recorded on the tape are read. If corresponding S.S.F. data
are found in the memory, these data are output.
If corresponding S.S.F. data are not found in the memory,
the tape is rewound to the beginning once more, and after
about 20 seconds of slow playback the stop mode is entered.
During slow playback, if S.S.F. data are written at the
beginning of the tape, these data are read out, and after the
stop mode is entered the S.S.F. data are output.
If S.S.F. data does not exist, the 05h (NOT TARGET)
command is output.
63
Advertisement
Table of Contents
