Tippmann A-5 MARKER LINE Owner's Manual page 15

Upper Receiver Disassembly: (continued from page 25)
3) ❏ Remove the 5 receiver bolts
on Response TM Marker) holding the upper
E
receiver halves together.
❏ To reassemble upper receiver follow the
N
Upper Receiver Assembly instructions below.
G
Upper Receiver Assembly
L
For Response TM Marker only: Install two parts
I
half before assembling receiver halves.
❏ ❏ ❏ ❏ ❏ 1) Oil o-ring
of the exterior flow control adapter
S
❏ ❏ ❏ ❏ ❏ 2) Align threaded opening of interior flow connector
H
fitting to inside of right receiver half.
❏ ❏ ❏ ❏ ❏ 3) Carefully thread adapter
receiver half into and tighten
(do not overtighten and strip threaded parts
or damage o-ring ).
1) Make sure all parts are clean before reassembling. Place right upper
receiver half flat with Tombstone Latch & Spring, Front Grip Nut, Receiver
O-ring and Ball Latch in position as shown below.
2) With left hand, grip left upper
receiver half as shown to hold
Cocking Handle and spring in place
by applying side pressure with
index finger pushing in direction of
arrows against Cocking Handle.
Cocking Handle Spring
Right
Hand
Left
Half
Receiver O-ring
Tombstone
Latch & Spring
properly inserted
WARNING
DO NOT REASSEMBLE WITHOUT MAKING SURE
TOMBSTONE LATCH & SPRING ARE PROPERLY
INSERTED IN PLACE AS SHOWN.
4) Use your finger tips to guide the left half straight down on to the right half
(4
& to the right receiver
.
through the right
with a 3/8" wrench
3) With left hand holding as shown below,
use right hand to seat cocking handle with
spring into receiver cutout then position
edge of spring in end of spring cutout
bowed as shown below. Then grip left
receiver with right hand as shown.
Cocking Handle
will be
bowed.
Front Grip Nut
with flat side facing
Latch
Spring bottom of marker.
26 Upper Receiver Assembly
(continued on page 27)
Upper Receiver Assembly (continued from page 26)
until receiver halves fit flush. If it does not fit flush the first time, check to
make sure the spring and other parts have stayed in place and repeat until
halves fit flush.
5) Insert 5 (4 on Response
bolt yet) & tighten them just enough to hold halves flush yet loose enough
to allow you to now insert and twist Barrel / Adapter unit (or FLATLINE
clockwise to reinstall.
6) Insert Front Sight with its slot facing back of marker, into the top front
of the receiver and insert the front sight bolt to hold in place.
7) Make sure all receiver bolts are tight (do not overtighten & strip threads).
FLATLINE TM
❏ First follow ❏ Unloading Your Marker and ❏ Air Supply Cylinder
Removal instructions on pages 18-20. Never disassemble a marker
that is under pressure or pressurize a partially assembled marker.
Flatline Barrel Removal:
TM
❏ Loosen 3 receiver bolts (A, B & C - see below) then turn barrel /
adapter to left and remove as one piece from upper receiver.
Flatline TM Barrel Installation:
1) ❏ Loosen 3
receiver bolts
(A, B, & C).
Left
Hand
A
Right
B C
Half
Ball
Latch
❏
4) While keeping cap screw and front sight aligned, tighten the
3 receiver screws A, B & C
to complete the installation.
Barrel at top
Proper screw position
Properly installed barrel will look like this.
TM Marker) Receiver Bolts
Barrel Removal & Installation
2) ❏ Position the Barrel
Adapter cap screw
facing to the left toward
the feeder housing and
insert into receiver.
Feeder
Housing
Cap
screw
to the
left
Proper
screw
position
27
E
N
(not front sight
G
TM )
L
I
S
H
3) ❏ Turn the Barrel
Assembly 1/4 turn to the
right until the adapter
cap screw aligns with
the front sight.
Front
Sight
Cap
Screw
A
B
C