Tippmann A-5 MARKER LINE Owner's Manual page 14

To reassemble the lower receiver: (continued from page 23)
❏ On A-5
TM E-Grip TM : make sure trigger guard
E-Grip TM assembly (with armature spacer
E
); are positioned in the right grip half as shown below. Position wires
around the posts as shown so wires are not pinched or sheared when
N
the left grip half is replaced. Visually inspect wires for damage or
G
disconnected wire ends at
L
TM TM
A-5 E-Grip Model Specific
Parts: Not Shown on A-5
I
Basic Parts List on pages 16-17.
S
TM
E-Grip parts shown in position in
H
the Right Trigger Plate with basic
parts (Note: E-Grip TM
Specific parts
TA01022
in bold).
Safety
Selector
02-33 Pins (4)
TA10073 Sear
02-20S
02-67R
Trigger
Right
Spring
Trigger
(Red-short)
02-33A Plate
Sear Pin
TA10021 02-88
Sear
(black)
Trigger
Spring
(silver - long)
TA10072 Magnet
(the red dot on the magnet must be
visible on this side of the trigger to
operate properly).
02-67L Left Trigger Plate
TM TM
NOTE: A-5 E-Grip Sear Spring 02-88 has tensions specifically designed for the E-
TM
Grip and it will not operate properly if you replace this spring with any other spring.
Double Trigger Kit (Optional, not included with A-5
Installation: The trigger slider & spring
removed from the double trigger before installation into the E-
Grip TM . Remove pins and
remove the trigger slider & spring.
NOTE: If the double trigger kit does not include a magnet -
take the magnet from the single trigger that came with your
marker and insert the magnet at
must be visible (see above) to operate properly.
, 2 adapter nuts
and armature
.
E-Grip TM Electronics
Assembled ;
TM
trigger guard
and 2 adapter
nuts - shown
positioned in the right
grip half for reassembly
TM
of the E-Grip - see above.
TA01019
Lower Receiver Right
TA99500
Electronics Assembly
Frame Half - Right
Armature
Spacer
Electronics
board
Frame
Half - Left
TA01018
TA07074
Lower
AdapterBolt
Receiver
(short)
Left
98-01B
TA10066
Adapter Bolt (long)
Battery Door
TA02061 Tank Adapter
TM
E-Grip
will need to be
from the double trigger and
(the red dot on the magnet
24
Lower Receiver Disassembly/Assembly:
(continued on page 25)
Lower Receiver Disassembly/Assembly: (continued from page 24)
2) ❏ Replace left grip half
, and
❏ Reinstall the battery door on A-5
in place
3) ❏ Reinstall the trigger assembly
into the left side of the grip (on E-Grip
Selector Switch
grip and then rotate it to the "SAFE" =
4) ❏ Attach the Tank Adapter: Slide tank adapter
and align holes; ❏ Insert receiver bolt
position the tank adapter and insert the 2 tank adapter bolts
(the short adapter bolt
❏ ❏ ❏ ❏ ❏ To attach the lower receiver (grip) to the upper receiver:
❏ Check to becertain the
trigger plates have not
separated and the trigger
assembly is intact as
shown. If there are gaps
at between the trigger plates
squeeze the plates together to look as shown.
(On the A-5
couple drops of marker oil onto the cylinderfitting
o-ring
❏ Line up the lower receiver front push pin holes
with the upper receiver holes then gently rock
CA-08B
rear of grip until you can insert the two lower
Adapter
receiver push pins
Nut (2)
❏ ❏ ❏ ❏ ❏ To disassemble the upper receiver
disassemble upper receiver halves to access the ball latch, front grip nut, cocking
handle, cocking handle spring, receiver o-ring, Tombstone latch and Tombstone
latch spring (plus the flow connector fitting on A-5
❏ 1) Follow the Marker/Receiver Disassembly/Assembly instructions beginning
on page 21 until you have removed the drive assembly parts on page 22.
❏ 2) Remove the Cyclone
Feed System: ❏ Remove the
TM Marker):
banjo fitting
bolt from
upper receiver
(and on Response
remove the flow control
adjustor fitting and banjo fitting bolt from the upper receiver - see
Response
from the left front side of upper receiver and remove the feed system
(NOTE: To install the Cyclone
. ❏ Secure grip halves with 3 grip screws
TM
E-Grip
into the grip and insert the safety
TM
and ❏ insert it into the left side of the
straight up
goes in front - see page 23).
and the trigger
marker, ❏ first put a
TM Response TM
in the lower receiver.)
& to attach.
TM
TM marker -
parts on page 14). ❏ Remove the Cyclone
TM
Feed System reverse the process).
TM
25
.
TM
(see instructions - page 9).
marker: ❏ Rotate the Safety
G
position).
into lower receiver
and tighten ( on A-5 TM E-Grip TM
and
or the sear –
: NOTE: It is only necessary to
TM Response TM Marker).
housing bolt
TM
Upper Receiver Disassembly:
(continued on page 26)
E
N
L
I
S
H