HP StorageWorks P9000 Reference Manual page 116

Option
-gvinf
-gvinfex
-svinf[=PTN]
-svinfex[=PTN]
-gplba
-gplbaex
-fv
1 16 Command tools
Description
Windows systems only. -gvinfex is for GPT disk.
Gets the signature and volume layout information of a raw device file provided via STDIN or
arguments, and saves this information to the system disk with the following format:
\WindowsDirectory\VOLssss_llll.ini
where ssss = serial#, llll = LDEV#
Normally this option is used to save the signature and volume layout information once after setting
the new partition for S-VOL using the Windows Disk Management.
Windows systems only. -svinfex[=PTN] is for GPT disk.
Sets the signature and volume layout information that was saved to the system disk to a raw device
file provided via STDIN or arguments. Gets the serial# and LDEV# for the target device using SCSI
Inquiry, and sets the signature and volume layout information into VOLssss_llll.ini file to the target
device. This option will set correctly because the signature and volume layout information is managed
by the serial# and LDEV# without depend on Harddisk#, even if Harddisk# is changed by the
configuration changes.
[=PTN]: Specifies a strings pattern to interpret the strings provided via STDIN as a raw device.
\Device\HarddiskVolume#( number ) is made in a sequential order executed -svinf to Harddisk,
and its number will remain the same as long as the system configuration is not changed. If you
want to make \Device\HarddiskVolume#( number ) more absolutely, then make
\Device\HarddiskVolume# in serial# and LDEV# order by using the "-sort" option as shown below:
D:\HORCM\etc>echo hd5 hd4 hd3 | inqraid -svinf -sort [VOL61459_451_5296A763] ->
Harddisk3 [OPEN-3 ] [VOL61459_452_5296A760] -> Harddisk4 [OPEN-3 ]
[VOL61459_453_5296A761] -> Harddisk5 [OPEN-3 ]
Windows systems only. -gplbaex is for GPT disk.
Displays usable LBA on a physical drive in units of 512 bytes, and specifies [slba] [elba] options
for raidvchkset command.
Example:
C:\HORCM\etc>inqraid $Phys -CLI -gplba -sort Harddisk11 : SLBA =
0x00003f00 ELBA = 0x000620d9 PCNT = 7 [OPEN-3-CVS ] Harddisk12 : SLBA
= 0x00003f00 ELBA = 0x00042ad1 PCNT = 4 [OPEN-3-CVS ] Harddisk13 : SLBA
= 0x0000003f ELBA = 0x000620d9 PCNT = 1 [OPEN-3-CVS ]
SLBA: Displays usable starting LBA in units of 512 bytes. ELBA: Displays usable ending LBA (ELBA
- 1 ) in units of 512 bytes. PCNT: Displays the number of partitions.
Example for setting of Harddisk1 1: C:\HORCM\etc>raidvchkset -d hd11 -vs 16
0x00003f00 0x000620d9
Windows systems only.
Displays the Volume{GUID} via $Volume with wide format.
Example:
C:\HORCM\etc>inqraid -CLI $Vol -fv
DEVICE_FILE PORT SERIAL LDEV CTG H/M/12 SSID R:Group PRODUCT_ID
Volume{cec25efe-d3b8-11d4-aead-00c00d003b1e}\Vol3\Dsk0 CL2-D 62496 256
- - - - OPEN-3-CVS-CM