H2: Digital Outputs - YASKAWA GA500 GA50U Series Programming Manual

1.10 H: Terminal Functions
Setting Value Function
175 !Up 2 Command
176
!Down 2 Command
177
!ASR Gain (C5-03) Select
178 !Analog TorqueRef Polarity
Invert
17E !Reverse Rotation Identifier
17F !PID Bi-Directional Enable
19F !DWEZ Disable
◆

H2: Digital Outputs

No.
Name
(Hex.)
H2-01 Term MA/MB-MC Function
Selection
(040B)
H2-02 Term P1-C1 Function
Selection
(040C)
H2-03 Term P2-C2 Function
Selection
(040D)
H2-06 Watt Hour Output Unit
Selection
(0437)
64
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
When the terminal deactivates, the motor accelerates by increasing the frequency reference bias value. Set !Up 2 Command and !
Down 2 Command together.
Note:
When you use the functions, set the optimal bias limit values with d4-08 and d4-09 [Up/Down 2 Bias Upper Limit/Lower Limit
(Up/Down 2)].
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
When the terminal deactivates, the motor decelerates by decreasing the frequency reference bias value. Set !Up 2 Command and !
Down 2 Command together.
Note:
When you use the functions, set the optimal bias limit values with d4-08 and d4-09 [Up/Down 2 Bias Upper Limit/Lower Limit
(Up/Down 2)].
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the function to switch the ASR proportional gain to C5-01 [ASR Proportional Gain 1] or C5-03 [ASR Proportional Gain 2].
ON : C5-01
OFF : C5-03
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the rotation direction of the external torque reference.
ON : External torque reference forward direction
OFF : External torque reference reverse direction
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the motor rotation direction when you use Simple Closed Loop V/f Control method.
ON : Forward run
OFF : Reverse run
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Switches the PID Bi-Directional output to enable or disable.
ON : Disable
OFF : Enabled
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Switches the DriveWorksEZ program saved in the drive to enable or disable.
ON : Enabled
OFF : Disable
Note:
Set A1-07 = 2 [DriveWorksEZ Function Selection = Digital input] to use this function.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the function set for MFDO terminal MA-MC or MB-MC.
Note:
Set this parameter to F when the terminal is not being used or to use the terminal in through
mode.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the function for MFDO terminal P1-C1.
Note:
Set this parameter to F when the terminal is not being used or to use the terminal in through
mode.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the function for MFDO terminal P2-C2.
Note:
Set this parameter to F when the terminal is not being used or to use the terminal in through
mode.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the unit for the output signal when H2-01 to H2-03 = 39 [MFDO Function Selection = Watt
Hour Pulse Output].
0 : 0.1 kWh units
1 : 1 kWh units
2 : 10 kWh units
3 : 100 kWh units
4 : 1000 kWh units
Description
Description
YASKAWA TOEPYAIGA5002A GA500 DRIVE PROGRAMMING
Default
(Range)
E
(0 - 1FF)
0
(0 - 1FF)
2
(0 - 1FF)
0
(0 - 4)