F6: Communication Options - YASKAWA GA500 GA50U Series Programming Manual

No.
Name
(Hex.)
F1-11 Speed Deviation Detect
DelayTime
(038A)
F1-14 Encoder Open-Circuit Detect
Time
(038D)
◆

F6: Communication Options

No.
Name
(Hex.)
F6-01 Communication Error
Selection
(03A2)
F6-02 Comm External Fault (EF0)
Detect
(03A3)
F6-03 Comm External Fault (EF0)
Select
(03A4)
F6-04 bUS Error Detection Time
(03A5)
F6-06 Torque Reference/Limit by
Comm
(03A7)
F6-07 Multi-Step Ref @ NetRef/
ComRef
(03A8)
F6-08 Comm Parameter Reset
@Initialize
(036A)
YASKAWA TOEPYAIGA5002A GA500 DRIVE PROGRAMMING
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the length of time that the difference between the frequency reference and speed feedback must
be more than the level in F1-10 to cause dEv [Speed Deviation].
Note:
When A1-02 = 0 [Control Method Selection = V/f], set H6-01 = 3 [Terminal RP Pulse Train
Function = Speed Feedback (V/F Control)] to enable this parameter.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the length of time that the drive must not receive a pulse signal to cause PGo [Encoder (PG)
Feedback Loss].
Note:
Motor speed and load conditions can cause ov [Overvoltage] and oC [Overcurrent] faults.
When A1-02 = 0 [Control Method Selection = V/f], set H6-01 = 3 [Terminal RP Pulse Train
Function = Speed Feedback (V/F Control)] to enable this parameter.
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the method to stop the motor or let the motor continue operating when the drive detects bUS
[Option Communication Error].
0 : Ramp to Stop
1 : Coast to Stop
2 : Fast Stop (Use C1-09)
3 : Alarm Only
4 : Alarm (Run at d1-04)
5 : Alarm - Ramp Stop
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the conditions at which EF0 [Option Card External Fault] is detected.
0 : Always Detected
1 : Detected during RUN Only
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the method to stop the motor or let the motor continue operating when the drive detects EF0
[Option Card External Fault].
0 : Ramp to Stop
1 : Coast to Stop
2 : Fast Stop (Use C1-09)
3 : Alarm Only
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the delay time for the drive to detect bUS [Option Communication Error].
Note:
When you install a CC-Link option (SI-C3) to the drive, the setting value changes to 0.0 s.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
Sets the function that enables and disables the torque reference and torque limit received from the
communication option.
0 : Disabled
1 : Enabled
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the function that enables and disables the multi-step speed reference when the freqency
reference source is NetRef or ComRef (communication option card or MEMOBUS/Modbus
communications).
0 : Disable Multi-Step References
1 : Enable Multi-Step References
V/f OLV OLV/PM AOLV/PM EZOLV OLV/PM
Sets the function to initialize F6-xx and F7-xx parameters when the drive is initialized with A1-03
[Initialize Parameters].
0 : No Reset - Parameters Retained
1 : Reset Back to Factory Default
Description
Description
1.9 F: Options
Default
(Range)
0.5 s
(0.0 - 10.0 s)
2.0 s
(0.0 - 10.0 s)
Default
(Range)
1
(0 - 5)
0
(0, 1)
1
(0 - 3)
2.0 s
(0.0 - 12.0 s)
0
(0, 1)
1
(0, 1)
1
0
(0, 1)
47