Table of Contents
Advertisement
EN
11
Charge Station Dimensions
See Fig. 29.
12
Settings
NOTE
You can adjust the settings of your Webasto
TurboConnect Charge Station using the following
options.
For installation:
– Webasto Charger Setup app
For operation and setting:
– Webasto ChargeConnect portal
– Webasto ChargeConnect app
– Integrated WebUI (configuration interface, see
chapter 8, "WebUI" on page 16)
13
Operation
13.1 LED and acoustic indicators
State
Status
Description
Indicator
Unpowered
Off
Blue, center
Power On
single LED,
solid
Blue, full bar,
Standby
solid
Blue, full bar,
Charging
pulsing
Blue, center
Locked
single LED,
intermittent
18
State
Status
Indicator
Plugging In
Update /
Rebooting
SelfCheck
mode
Charging
Reduced
(Overhea-
ting)
Station Error
State
Station fault
Station
Explanation
Electrical
fault
The charge station is
not powered.
Unplug
The charge station is
powered, and the "free
charging" mode is ON
Table 4:
Information on Status indicators
(default state).
The charge station is
NOTE
receiving power and
In case of a ground fault, additionally, an acoustic buzzer
is ready to charge the
signal will occur.
vehicle.
The charge station is
NOTE
successfully charging
A temporarily incorrect HMI state is not an indication
the vehicle.
of a defect or faulty condition of the TurboConnect
The charge station is
Charge Station. It does not affect the functions. If the
powered, and the "free
incorrect HMI state occurs repeatedly, the surrounding
charging" mode is OFF.
The charge station
environment of the TurboConnect Charge Station must
will not charge until
be checked for interfering wireless devices / installations
authorization or setting
and they must be eliminated. If that is not possible,
the "free charging"
select another installation location for the TurboConnect
mode to ON.
Charge Station with no disturbances. A dedicated circuit
for this installation is recommended.
13.2 Start Charging
Description
Explanation
To start a typical charging session:
The charge station
1. If the charge station is locked, unlock the charge station (see
White, full
is connecting to the
bar, cycling to
vehicle, preparing to
middle
2. Open the vehicle charging port cover.
charge.
3. Remove the coupler from the remote dock.
The charge station is
4. Plug the coupler into the vehicle charging port until it
White, wipe
downloading firmware
left to right
or rebooting after
changes to settings.
The charge station is
White, full bar,
checking that all status
solid
indicators are working.
5. As soon as the vehicle and charge station are connected,
Amber, full
The charge station
bar, solid
is charging at a
background.
reduced rate due to
Blue, center,
overheating.
pulsing
The charge station has
Amber, full bar,
a fault and requires
solid
troubleshooting.
The charge station has
Red, full bar,
experienced a non-
solid
recoverable fault.
The charge station has
Red, full bar,
experienced a ground
13.3 Stop Charging
blink
fault.
You will generally end a charging session when charging is
The charge station is
complete (indicated by the charge station status indicator
White, full bar,
being disconnected
being in a standby state), but you can also interrupt and end an
fade out
from the vehicle (a few
seconds).
incomplete charging session.
To stop a charging session:
1. Unlock and remove the coupler from the vehicle by pressing
2. Close the vehicle charging port cover.
3. Wrap the loose cable around the remote dock.
4. Plug the coupler into the remote dock.
5. Lock the charge station if desired.
13.4 Scan & Charge locking function
You can enable or disable the charge station locking function
in the Webasto Setup app or the WebUI. If you want to
restrict access to the charge station for other users, disable
"free charging" in the Webasto Setup App. The Webasto
ChargeConnect App then offers the option of enabling
individual charging processes via the supplied Scan & Charge
QR codes, which are in the scope of delivery. Instructions for
charging in the locked state:
Table 4, "Information on Status indicators" on page 18).
clicks. The charge station should indicate that the vehicle
is establishing a connection to the charge station. The
charging cable must not be subjected to any strain during
use as shown in Fig. 27.
the charge station indicator exhibits one of the following
states:
– The charge station will be on standby if the vehicle is fully
charged or scheduled to charge later.
– The charge station will begin charging.
NOTE
A shutdown, or a reduction in charging current, may
occur to prevent the charge station from overheating.
This is a safety feature.
the coupler button. The charge station should return to
Power On state.
Webasto TurboConnect
Advertisement
Table of Contents
