Table of Contents
Advertisement
EN
3.2
General Safety information
DANGER
– You must comply with the locally applicable
requirements regarding electrical installations, fire
protection, safety regulations, and escape routes
at the intended installation location.
– Hazardous voltages are present within the casing.
– The TurboConnect Charge Station does not have
its own power ON/OFF switch. The protective
devices (circuit breakers) installed in the power
supply system are therefore also used to
disconnect the power supply.
– Inspect the charge station for visual damage
before installation and use. Do not use the charge
station if it is damaged.
– Installation, electrical connection, and initial
operation of the charge station must be carried
out by a qualified electrician.
– The screw-mounted unit cover may only be
removed by qualified electricians. Do not remove
the unit cover whilst in operation.
– Do not remove markings, warning symbols, or
the type plate from the charge station.
– The charging cable may only be replaced by
qualified electricians and in accordance with the
installation manual.
– You are prohibited from connecting other
equipment / devices to the charge station than
those for which the charge station was designed
and intended.
– When not in use, store the charging cable in the
designated holder and lock the charging coupling
in the remote dock. Loosely wind the charging
cable around the remote dock making sure the
cable does not touch the floor.
– You must make sure that the charging cable
and coupling cannot be driven over or trapped.
Protect it from all other hazards.
– Immediately notify Customer Service if the charge
station, charging cable, or charging coupling is
damaged. Do not continue to use the charge
station.
8
– Prevent the charging cable and coupling from
contact with external heat sources, water, dirt,
and chemicals.
– Switch off the power at the circuit breaker before
installing or cleaning.
– Do not attach extension cables or adapters to the
charging cable.
– Only remove the charging cable by pulling on the
charging coupling.
– Never clean the charge station with a high-
pressure cleaner or similar.
– Switch off the power supply before cleaning the
charging sockets.
– The charging cable must not be subjected to any
strain during use.
– You must make sure that no one has access to
the charge station without reading this user
manual first.
– Make sure that the charge station temperature
is within its storage temperature limits when
moving, transporting, or storing it.
– You are prohibited from pulling the charge station
by its cable.
– The charge station must be connected directly
to your home's mains connection; no plugs and
sockets must be used.
– Do not put your fingers into the electric charger
coupler.
– You may only operate the charge station after
professional installation.
– When transporting the charge station, handle
it with care. Do not subject it to strong force or
impact, also do not pull, twist, tangle, drag, or
step on the TurboConnect Charge Station, to
prevent damaging it or any of its components.
NOTE
In addition to the safety instructions in this document,
also observe further safety instructions in any other
enclosed or online available documents.
Please visit the webpage regularly to be updated on
safety and operational instructions.
3.3
Safety information for installation
DANGER
– The instructions in this document must be
followed for safe installation.
– Installation and connection of the charge station
must only be carried out by a qualified electrician.
– You must comply with the locally applicable
requirements regarding electrical installations, fire
protection, safety regulations, and escape routes
at the intended installation location.
– Only use the supplied installation material and
other appropriate installation material.
– When the charge station is open, ESD
(electrostatic discharge) precautions must be
taken properly to avoid electrostatic discharge.
– When handling electrostatically sensitive boards,
wear grounded antistatic wrist straps and properly
observe ESD safety precautions. Wrist straps must
only be used when mounting and connecting the
loading unit. Wrist straps must never be worn on
a live TurboConnect Charge Station.
– Electricians must be properly grounded during the
installation of the TurboConnect Charge Station.
– Do not install the charge station in an explosion-
sensitive area (Ex Zone).
– Install the charge station in such a way that the
charging cable does not block any passageways.
– Do not install the charge station in areas subject
to ammonia or air-containing ammonia.
– Do not install the charge station in a location
where falling objects may damage it.
– The charge station is suitable for use indoors as
well as outdoors.
– Do not install the charge station in the vicinity of
water jets, such as car-wash installations, high-
pressure cleaners, or garden hoses.
– Protect the charge station against damage
caused by sub-zero temperatures, hail, or similar.
We would like to refer you to our enclosure
protection class NEMA 4. See chapter 22,
"Technical data" on page 21.
Webasto TurboConnect
Advertisement
Table of Contents
