Subscribe to Our Youtube Channel
Related Manuals for Webasto TurboConnect
Summary of Contents for Webasto TurboConnect
- Page 1 TurboConnect™ EV Charge Station Quick Start Guide ETL and ETLc listed product per ANSI / UL standards UL2594, UL2231-2, UL1998 READ AND SAVE THESE INSTRUCTIONS Certified to CAN / CSA standard C22.2 No. 280...
- Page 6 (0.5 x 3.5 mm) Webasto TurboConnect (29 mm) Wichtige Hinweise zur bedienings - und Einbauanweisung ..........1 T(x)6, T(x)20, T(x)25 (3 mm) 10.16 in 5.67 in (258 mm) (144 mm) 3.5 in (89 mm) 13.70 in 17.83 in (348 mm) (453 mm) 4.92 in...
-
Page 7: Table Of Contents
Federal Communications Commission (FCC) statement Transportation and storage Legal Notice Scope of delivery Technical data Installation and electrical connection Checklist for the installation of the Webasto charge station Required tools Digital installation and user apps Product location considerations Criteria for the electrical connection Installation Apply Scan &... -
Page 8: Quick Start Guide For App Solutions
Webasto ChargeConnect app Wichtige Hinweise zur bedienings - und Einbauanweisung ..........1 The charge station must be installed by a qualified Download the required Apps. Open the Webasto Charger Setup app and configure electrician. your charge station. For installation: Webasto Charger Setup. -
Page 9: General Information
States, Canada, and other countries. It may not be modified, NOTE reproduced, or distributed without the prior, express written Webasto shall not assume liability for defects or damage We would draw your attention to the fact that, as consent of Webasto. Webasto and TurboConnect are U.S.-... -
Page 10: General Safety Information
– Hazardous voltages are present within the casing. – You must comply with the locally applicable – Only remove the charging cable by pulling on the – The TurboConnect Charge Station does not have requirements regarding electrical installations, fire charging coupling. -
Page 11: Safety Information For Electrical Connection
WARNING without access restrictions. GROUNDING INSTRUCTIONS This document describes the TurboConnect Charge Station. You The product must be connected to a grounded, metal, – Protect the charge station from direct sunlight. can find the exact device details on the type plate of the charge... -
Page 12: Interface Descriptions
Ferrite kit (incl. ferrite & cable tie) 4.2.1.2 Modbus TCP Manual The TurboConnect Charge Station is set up for the use of an “Scan & Charge” QR codes go to: extended energy management system (EMS) via a higher- https://apps.apple.com/ (Apple App Store) or... -
Page 13: Product Location Considerations
The following points must be considered when selecting the High voltages every power supply pole of the TurboConnect Charge Station The danger of fatal electric shock. installation location for the TurboConnect Charge Station and is disconnected if a fault occurs. -
Page 14: Installation
4. All not used entry interfaces must be covered with blind See chapter 11, "Charge Station Dimensions" on page 18, plugs to meet ingress protection NEMA 4. for product dimensions and drilling template to determine the installation position. Webasto TurboConnect... - Page 15 4. Connect the charging cable wires by properly pushing them in-lbs.). into the terminals (X-L1, X-L2, and X-PE) as shown in Fig. 12 then tighten the screws using a crosshead screwdriver with a torque of 22.2 in-lbs. (2.5 Nm) (Type PZ2). Webasto TurboConnect...
- Page 16 High voltages 7.5.8 Connecting the ethernet cable (optional) The danger of fatal electric shock. The TurboConnect Charge Station can be connected by wire Ensure safe isolation from the power supply. (LAN) to the network infrastructure with an ethernet cable Webasto TurboConnect...
-
Page 17: Apply Scan & Charge Qr Code
2. Start the Webasto Charge Connect App. The TurboConnect Charge Station is now fully installed (Fig. 24). the trim cover using pliers or a similar tool. See Fig. 19. For best 3. -
Page 18: Webui
The configuration of the DLM in the WebUI will be described below. For more information see chapter 9, "Dynamic Load management – Stand-alone mode (DLM)" on page 17. 1. Select the HEMS (Home Energy Management System) tab in the WebUI. Webasto TurboConnect... -
Page 19: Dynamic Load Management - Stand-Alone Mode (Dlm)
Stand-alone mode (DLM) (HEMS) grid panel. The TurboConnect Charge Station has a local, dynamic load The TurboConnect Charge Station can be integrated into a management stand-alone function. Here, one smart meter range of energy management systems (EMS). Here, the external... -
Page 20: Charge Station Dimensions
You can enable or disable the charge station locking function incorrect HMI state occurs repeatedly, the surrounding charging" mode is OFF. Blue, center in the Webasto Setup app or the WebUI. If you want to The charge station environment of the TurboConnect Charge Station must Locked... -
Page 21: 15 Decommissioning The Product
1. Connect the TurboConnect charging cable to the charging HMI state Recommended actions HMI state Recommended actions port on your vehicle. In the locked state, a charging process 1. Make sure that the vehicle coupler is properly 1. Make sure the Wi-Fi signal at the charge station inserted into the vehicle. -
Page 22: 16 Maintenance, Cleaning, Repair
If this equipment does cause harmful interference to – FCC Part 15, Subpart B and C Clean the TurboConnect Charge Station only with a dry cloth. radio or television reception, which can be determined – ICES-003 Do not use aggressive cleaning agents, wax, or solvents. -
Page 23: Technical Data
Network interface (wired) Ethernet / LAN, IEEE 802.3u – 100BASE-TX, RJ-45 port Network interface (wireless) Wi-Fi IEEE 802.11 a/b/g/n – up to 150 Mbit/s Authentication and mobile communications Wi-Fi -Webasto Charger Setup-App OCPP Version 1.6j Mechanical data Dimensions (W × H × D) 10.2 x 17.7 x 5.5 Inches / 258 x 450 x 141 mm... - Page 24 Other standards and guidelines – FCC Part 15, Subpart B and C – ICES-003 – RSS-GEN, RSS-247 – NEC Article 625 compliant Tested with OCPP backend(s) Webasto Charge Connect OCPP (Open Charge Point Protocol) backend Table 6: Technical data Webasto TurboConnect...
-
Page 25: Checklist For The Installation Of The Webasto Charge Station
Checklist for the installation of the Webasto charge station Please complete the TurboConnect Charge Station commissioning report. Serial number: Material number: 240 V (residential split phase) Voltage 208 V (industrial) General preconditions: Installation, electrical connection, and initial operation of the charge station have been carried out by a qualified electrician. - Page 26 To request this documentation in another language, please locate and contact your local Webasto dealer. You can find your nearest dealer at: https://www.evsolutions.com/. To provide feedback (in English or German), please email: feedback2tdt@webasto.com. Webasto Customer Service: +1 (888) 833-2148 evcs@webasto.com Webasto Charging Systems Inc.
Need help?
Do you have a question about the TurboConnect and is the answer not in the manual?
Questions and answers