Webasto Pure Installation Instructions Manual
Hide thumbs
Also See for Pure:
- Operating instructions manual (9 pages) ,
- Installation instructions manual (75 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Webasto Pure
Summary of Contents for Webasto Pure
- Page 1 Installation Instructions Webasto Pure English...
-
Page 2: Table Of Contents
To replace the charging cable..... 8 10 Disposal .......... 8 11 Declaration of conformity .... 9 12 Assembly .......... 10 13 Technical data ........ 11 14 Check list for the installation of the Webasto charging station.... 12 II Webasto Pure EN... -
Page 3: General Information
Intended use ways observe these. The Webasto Pure charging station is designed for charging General safety information electric vehicles in accordance with IEC 61851-1, charge mode n Hazardous voltages are present within the casing. -
Page 4: Safety Information For Installation
Only use the supplied installation material. out only by an electrician. n The Webasto Pure safety concept is based on a power n Prior to initial start-up, the electrician must check that supply system that is earthed at all times. The electri- the charging station has been connected correctly. -
Page 5: Installation And Electrical Connection
NOTE 7.2.2 Dimensioning of the circuit breaker The Webasto Pure safety concept is based on a power The circuit breaker must conform to IEC 60898. The let-through supply system that is earthed at all times, which must always be ensured by an electrician during installation. -
Page 6: Electrical Connections
Secure the wires to the connection terminals as illustrated. Place the mounting frame in level position. Secure the mounting frame with the 2 short screws and washers on the top holes. Remove the bottom cover from the housing. 6 / 13 II Webasto Pure EN... -
Page 7: Dip Switch Settings
8. * The charging current is already limited to 16 A in the factory in the case of an 11 kW variant. WCH000011A A Webasto Pure programmed for 11 kW cannot be set to 22 kW with the DIP switches. Fig. 4... -
Page 8: Dim Led Indicator (Option 1)
NOTE Set key-operated switch back from OFF to ON to switch to The charging cable may be replaced a maximum of four standby mode. times during the service lifetime of the Webasto Pure. Deactivate charging current limit NOTE (option 2) Refer to the Webasto online shop for part numbers: www.webasto-charging.com... -
Page 9: Declaration Of Conformity
The Webasto Pure was developed, manufactured, tested and supplied in accordance with the relevant directives, regulations and standards for safety, EMC and environmental compatibility. Webasto declares that the product Webasto Pure is manufac- tured and delivered in accordance with the following directives and regulations: –... -
Page 10: Assembly
12 | Assembly Assembly WCH000014A Fig. 7 WCH00001A Fig. 8 All dimensions specified in mm. 10 / 13 II Webasto Pure EN... -
Page 11: Technical Data
Altitude [m] max. 2000 (above sea level) Permissible relative humidity [%] 5 up to 95 Non-condensing Weight [kg] 11 kW: 4.6 22 kW: 5.6 Dimensions [mm] See figures in chapter 12, "Assembly" on page 10 II Webasto Pure EN 11 / 13... -
Page 12: Check List For The Installation Of The Webasto Charging Station
The charging cable and coupling has been protected against being driven over, trapped or any other mechanical haz- ards. The customer/user was informed how the Webasto Pure voltage is switched off with the installation-side protective devices. Charging station requirements: The cable support sleeves for the power cable and data cable (for live only) have been fitted during installation. - Page 13 These are the original instructions. The German language is binding. You can request your language if it is missing. The telephone number of each country can be found in the Webasto ser- vice centre leaflet or the website of the respective Webasto representative of your country.
Need help?
Do you have a question about the Pure and is the answer not in the manual?
Questions and answers