Interface Descriptions; Transportation And Storage; Scope Of Delivery; Installation And Electrical Connection - Webasto TurboConnect Quick Start Manual

EN
4. Click Download to download the generated PNG file.
5. You can optionally insert the PNG file into a Word
document.
6. Print the downloaded PNG file or Word document.
4.2

Interface Descriptions

4.2.1 Hardware interfaces
The Charge Station contains various hardware interfaces (see
Fig. 28). Each interface serves another purpose. The following
table shows detailed descriptions of each interface.
1 DIP switches (1 to 6)
2 Connector for CP
Power supply terminal blocks for grid input and charging
3
cable output wires
4 RJ 45 port
4.2.1.1 Ethernet / RJ45 / LAN
To connect the TurboConnect Charge Station to a network,
use an ethernet cable with an RJ45 jack to plug into the RJ45
port on the electronic board. You can also configure and
control the charge station using this connection. The control
system requires a connection to the backend or a local energy
management system. Webasto recommends a CAT7 network
cable, but CAT6a is sufficient.
Follow the installation instructions in chapter 7.5.8, "Connecting
the ethernet cable (optional)" on page 14 for connecting the
TurboConnect Charge Station via an ethernet interface.
If you want to implement multiple functions via the LAN
interface, such as ModBus and an internet connection, a DHCP
network switch or router can be connected to the incoming
circuit of the building wiring system.
4.2.1.2 Modbus TCP
The TurboConnect Charge Station is set up for the use of an
extended energy management system (EMS) via a higher-
level electricity meter for multiple use cases, such as cluster
load management, or it can be connected to a Smart Meter
for circuit load balancing. These functions can be configured
through the web-config interface in the setting section.
4.2.1.3 Control Pilot (CP)
The charging cable comes with power supply lines and a data
line which is known as CP (control pilot) line (orange wire).
4.2.1.4 Power supply terminals
The terminal connectors for the grid wiring are marked L1, L2/N,
PE on the left side of the terminal block.
10
The terminal connectors for the charging cable are marked X-PE,
X-L2/X-N, X-L1 and are located on the right side of the terminal
block. See Fig. 28, position mark 3.
4.2.2 Wi-Fi
After completing the start process of the charge station, you
can connect a Wi-Fi-enabled computer or mobile device to the
charge station hotspot (standard configuration via Webasto
Charger Setup app). The Wi-Fi hotspot can be used to configure
the charge station (Webasto Charger Setup app). You can
connect the TurboConnect Charge Station to a Wi-Fi router to
establish an internet connection (configuration via Webasto
Charger Setup app or WebUI).
5

Transportation and storage

Observe the ambient temperature for storage during
transportation. See chapter 22, "Technical data" on page 21.
Transport the charge station only when suitably packaged.
6

Scope of delivery

Scope of delivery for the charge station. See Fig. 25.
A Main unit
B Design cover
C Charging cable with coupler
D Blind plugs
E Wall mount bracket
F Dock rear holder, dock front cover & dock insert
G Screws ⁄ x ⁄ inch (5 x 12 mm)
H Screws ⁄ x ⁄ inch (4 x 16 mm)
I Cable fixation
J Screws ⁄ x ⁄ inch (4 x 13 mm)
K Ferrite kit (incl. ferrite & cable tie)
L Manual
M "Scan & Charge" QR codes
7

Installation and electrical connection

Observe the safety information. See chapter 3, "Safety" on
page 7. Download the latest manual from the website for
updated instructions.
7.1

Required tools

To install the TurboConnect Charge Station, you need the tools
in the following table. See also Fig. 26.
AA Measuring tape
AB Pliers
AC Power drill
AD Slot-head screwdriver
AE Crosshead screwdriver
AF Combination wrench (1 9 ⁄ inch (29 mm))
AG Torx screwdrivers (T6 (included), T20, and T25)
AH Allen wrench ( 1 ⁄ inch (3 mm))
7.2

Digital installation and user apps

DANGER
You must observe the safety information. See chapter 3,
"Safety" on page 7.
Webasto Charger Setup app (for installation)
To download this app:
scan the QR code below or
go to:
https://apps.apple.com/ (Apple App Store) or
https://play.google.com/ (Google Play Store) as appropriate.
Webasto ChargeConnect app (for operation)
To download this app:
scan the QR code below or
go to:
https://apps.apple.com/ (Apple App Store) or
https://play.google.com/ (Google Play Store) as appropriate.
CAUTION
The TurboConnect Charge Station safety concept is
based on a power supply system that is earthed at all
times, which must always be ensured by an electrician
during installation.
Webasto TurboConnect