Honeywell Home T10 Product Data page 38

Firmware is occasionally updated at the factory or over the air. Some ISU settings may not be shown on models that lack the latest firmware.
ISU # Heading
2185 Emergency Emergency Heat Type
Heat
2190 External fossil External fossil Fuel Kit
Fuel Kit
2200 Backup Heat Backup Heat Operation
Operation
2205 Emergency Emergency Heat
Heat Operation
Operation
2210 Fan Control Backup Heat Fan
Operation
2230 Control mode Control Mode
3000 Changeover Changeover
3015 Auto
Changeover
Differential
3020 Staging control Finish with high cool
stage
3021 Staging control Finish with high heat
stage
3030 Staging control Cool differential stage 2
3050 Staging control Radiant heat differential
Heat Differentials
3060 Staging control Compressor Heat
Differential Stage 2
3080 Staging control Backup heat differentials Stage 1: Comfort*, 2.0F to
33-00462—05
Table 9. Installer Setup (ISU). (Continued)
Question Options
Electric Forced Air,
Standard Efficiency Gas
Forced Air, High Efficiency
Gas Forced Air, Oil Forced
Air, Hot Water Fan Coil, Hot
Water Radiant Heat, Other
Thermostat Controls
Backup Heat, External
Fossil Fuel Kit Controls
Backup Heat
NOT Allowed to Run with
Heat Pump, Allowed to Run
with Heat Pump
NOT Allowed to Run with
Heat Pump, Allowed to Run
with Heat Pump
No Fan, Equipment Controls
fan, Thermostat controls fan
Air and Floor, Air only,
Floor only
Manual, Automatic
0-5F (0.00 to 2.50C)
No, Yes
No, Yes
Comfort, 1.0F, 1.5F, 2.0F,
2.5F, 3.0F, 3.5F (.50, .75,
1.00, 1.25, 1.50, 1.75, C)
Comfort, 1.0F, 1.5F, 2.0F,
2.5F, 3.0F, 3.5F (.50, .75,
1.00, 1.25, 1.50, 1.75, C)
Stage 2 (Comfort, 1.0F -
3.5F)
Stage 3 (Comfort, 1.5F to
4.0F
Comfort, 1.0F, 1.5F, 2.0F,
2.5F, 3.0F, 3.5F (.50, .75,
1.00, 1.25, 1.50, 1.75, C)
15F (1.00C to 7.5C)
Stage 2: Comfort*, 2.5F to
15.5F (1.25F to 7.75F)
Contingent
previous EIM
setting? needed?
2175 = No*
independent
2000 = heat No
pump, 2180 =
Gas or oil
forced air
2180 set for No
Hot Water or
Other
2150 set for No*
Hot Water or
Other
2180 = other No
1055 set to No
"Wired"
Any system No
with at least 1
heat stage & 1
cool stage
3000= auto No
2 cool/ No
compressor
stages
At least 2 heat No
stages
2 cool stages No
selected
There are 2 No
stages of
radiant heat
selected for
2070.
2000 = No
Conventional
Forced air +
2070 = 2 or 3
2000 = Yes
Conventional
Forced air +
2070 = 3
2000 = Heat No
Pump and
2070
Compressor
stages = 2
Radiant heat No
with 1 or 2
backup heat
stages
Radiant heat Yes
with 2 backup
heat stages
34
T10, T10+
or both Notes
Both Not an option when
EIM is used.
Both
Both
Both Not an option when
EIM is used.
T10+
T10+ No Floor only option
if there is a cool
stage or backup
heat stage.
Both
Both
Both
Both
Both
Both
T10+
T10+
Both
Both If 2 stages of
backup heat. The
2nd backup stage is
forced to be at least
.5 degrees higher
T10+
than first stage
back-up heat.