Mitsubishi Electric FR-E800 Instruction Manual page 352

Increment
Monitor item
and unit
Option input terminal
—
*11
status
Option output terminal
—
*11
status
Option input terminal
status 1 (for
—
*11
communication)
Option input terminal
status 2 (for
—
*11
communication)
Option output terminal
status (for
—
*11
communication)
Motor thermal load
0.1%
factor
Inverter thermal load
0.1%
factor
PTC thermistor
0.01 kΩ
resistance
Ideal speed command 0.01 Hz
PID measured value
0.1%
*22
2
Emergency drive
1
status
*8*11
—
Cumulative pulse
Cumulative pulse
—
*8*11
overflow times
32-bit cumulative
1 kWh
energy (lower 16 bits)
32-bit cumulative
1 kWh
energy (upper 16 bits)
32-bit cumulative
0.01 kWh
energy (lower 16 bits)
32-bit cumulative
0.01 kWh
energy (upper 16 bits)
BACnet reception
1
*22
status
BACnet token pass
1
*22
counter
BACnet valid APDU
1
*22
counter
BACnet
communication error
1
*22
counter
BACnet terminal FM
0.1%
*22
output level
Communication
Pr.
Monitor Monitor
setting
*1
code 1 code 2
56 — —
57 — —
*14
—
H3A 40258
*15
—
H3B 40259
*16
—
H3C 40260
61 H3D 40261
62 H3E 40262
64 H40 40264
*17
65 H41 40265
67 H43 40267
68 H44 40268
71 H47 40271
72 H48 40272
— H4D 40277
— H4E 40278
— H4F 40279
— H50 40280
81 H51 40281
82 H52 40282
83 H53 40283
84 H54 40284
85 H55 40285
Negative
indication
*3
*2
(-)
The ON/OFF state of the digital input terminals on the
FR-A8AX or FR-E8AXY is displayed on the operation
panel. (Refer to
The ON/OFF state of the digital output terminals on the
FR-A8AY or FR-E8AXY or the relay output terminals on
the FR-A8AR is displayed on the operation panel.
(Refer to page 354
The ON/OFF state of the digital input terminals X0 to
*14
X15 on the FR-A8AX is monitored via communication.
The ON/OFF state of the digital input terminal DY on the
*15
FR-A8AX or the digital input terminals X1 to X7 on the
FR-E8AXY is monitored via communication.
The ON/OFF state of the digital output terminals Y0 to
Y6 on the FR-A8AY, the digital output terminals Y1 and
*16
Y2 on the FR-E8AXY, or the relay output terminals RA1
to RA3 on the FR-A8AR is monitored via
communication.
The accumulated heat value of the motor thermal O/L
relay is displayed.
The Motor overload trip (electronic thermal relay
function) (E.THM) occurs at 100%.
The accumulated heat value of the inverter thermal O/L
relay is displayed.
The Inverter overload trip (electronic thermal relay
function) (E.THT) occurs at 100%.
The PTC thermistor resistance is displayed when
Pr.561 PTC thermistor protection level ≠ "9999".
(The output voltage is displayed when Pr.561 = "9999".)
The speed command ideal to create a position
○
command.
The PID measured value is displayed while the PID
control is enabled (Pr.128 ≠ "0"), even if PID control
operating conditions are not satisfied. (Refer to
488.)
Emergency drive status is displayed. (Available for the
FR-E800 and FR-E800-E.) (Refer to
The cumulative number of pulses (after multiplied by
*21
○
four) is displayed.
The number of the cumulative pulse overflow times is
*21
○
displayed.
The upper or lower 16 bits of the 32-bit cumulative
energy is displayed on each indication.
Monitoring via communication is available.
The BACnet reception status is displayed. (Available
only for the FR-E800.)
The count of received token is displayed. (Available
only for the FR-E800.)
The count of valid APDU detection is displayed.
(Available only for the FR-E800, FR-E800-(SC)EPA,
and FR-E806-SCEPA.)
The count of communication error detection is
displayed. (Available only for the FR-E800.)
The value set in the Analog Output object (ID = 0:
Terminal FM) for BACnet communication is displayed.
(Available only for the FR-E800-1.)
12. (M) Item and Output Signal for Monitoring
12.2 Monitor item selection on operation panel or via communication
Description
page 354 for details.)
for details.)
page
page 322.)
11
12
13
14
15
16
17
18
19
20
351