Safety Instructions; Technical Data - Nakayama PD5230 Manual

EN
WARNING: Read through carefully and understand these instructions before use.

Safety instructions

Introduction
Thank you for your choice. Before use, read the instructions for use carefully to know how to use the machine properly and safely. Keep the manual for future
use in a safe place. The instructions should be attached with the machine when you are going to give it away or lend it to someone. Fully inform the machine
receiver to avoid damage or injury from improper use.
In addition, due to the continuous evolution of our products and changes in features, there may be differences depending on the market model.
CAUTION: If you use the machine properly, the earth auger is a powerful, fast and efficient tool. If used improperly or without security measures, it can be
dangerous. For a pleasant and safe job, strictly follow the safety instructions that come with this machine.
1. The machine should only be used by adults with good physical condition and knowledge of the instructions for use.
2. Do not operate the machine if you are tired or under the influence of alcohol or other substances.
3. Do not wear jewellery or loose clothing that may be caught in the moving parts of the machine.
4. Wear non-slip shoes, gloves, goggles, earmuffs and a helmet.
5. Before starting the machine, confirm that the speed is in the dead position.
6. Do not allow other people to be in the workplace when working with the machine.
7. Don't start unless you have a clean workplace. Do not work near power cables.
8. Use the machine only in well-ventilated areas and away from flammable materials.
9. Transfer the machine with the engine off, with the accessory removed and with the steering wheel folded.
10. Replace the component if it is broken or the other is damaged.
11. Fill the tank away from heat sources and with the engine off. Do not smoke. Do not remove the fuel cap if the engine is running. If fuel spills, move the
machine at least 3 meters from the point before you start.
12. Keep handles clean and dry.
13. Before starting, make sure that the accessory is not obstructed by an object.
14. Maintain a stable posture and a safe position.
15. Do not touch the accessory (array) and do not perform maintenance work when the engine is running.
16. Make sure the accessory does not move when the machine is idling.
17. Hold the machine firmly with both hands and keep your body away from the accessory and exhaust. It will provide you with support for transporting,
booting and using the machine.
18. Do not attempt to repair or maintain parts not listed in the maintenance paragraph. Contact the company's authorized service department.
19. Store the clover above the ground in a vertical position in a dry place without fuel.
20. Check the machine every day to make sure it is in good working order.
21. When working, move the machine from one point to another in idle mode and at speed to the dead position.
22. Do not use a machine that has a problem, is modified or has been repaired or incorrectly assembled. Do not remove or disable any of the security
components. Use only accessories that are suitable for this machine.
23. Do not try the spark plug near the cylinder.
24. Do not use the machine unless you have fully understood the operating methods. Follow the manufacturer's instructions on how to maintain it.
25. Do not use fuel to clean the machine.
26. If the trivet sticks, stop the machine immediately.
27. If your machine no longer works, discard it in an environmentally friendly way. Deliver it to the nearest recycling center for proper disposal.
28. Borrow your machine only to people who know how to operate it. Put together the instructions for use and safety to read them first.
29. All repair work other than those specified in these instructions should only be performed by authorized technical personnel.
30. Keep the machine in a safe place and use it only when needed.
31. Do not place the machine on a fixed base.
32. It is forbidden to use components and spare parts that the manufacturer does not recommend.
Pre-operational inspection
1. Check all bolts and nuts and make sure that they are securely tight, tighten where necessary.
2. Check the cutting blades and make sure that they are well fitted and void of cracking or chipping.
NEVER use a drill that is damaged.
3. Use only approved parts for repairs and maintenance.
Post-operational inspection
1. Before servicing the auger or making repairs. ALWAYS stop the engine, remove the plug cap from the spark plug and allow the engine to cool down.
2. Before storing the auger, drain all remaining fuel and wipe the clean dirt and weeds. NEVER store the auger near live flames.

Technical data

Displacement
Engine type
Horsepower
Cylinder diameter
Carburetor type
Gasoline/2-stroke oil mixing ratio
Fuel tank capacity
Idling speed
Drill diameter
Drill length
Additional features
2
52 cc
Air-cooled, two stroke, single cylinder
2 hp / 6500 rpm
44 mm
Pump-film type
30 ml of oil per 1 litre of gasoline
1000 ml
2800-3200 rpm
10 cm
80 cm
Easy start
WWW.NIKOLAOUTOOLS.GR
* The manufacturer reserves the right to make minor changes to product design and
technical specifications without prior notice unless these changes significantly affect the
performance and safety of the products. The parts described / illustrated in the pages of
the manual that you hold in your hands may also concern other models of the
manufacturer's product line with similar features and may not be included in the product
you just acquired.
* To ensure the safety and reliability of the product and the warranty validity, all repair,
inspection or replacement work, including maintenance and special adjustments, must
only be carried out by technicians of the authorized service department of the
manufacturer.
* Always use the product with the supplied equipment. Operation of the product with
non-provided equipment may cause malfunctions or even serious injury or death. The
manufacturer and the importer shall not be liable for injuries and damages resulting from
the use of non-conforming equipment.