Sevcon MillipaK 4QPM Manual page 63

Calibrator
Reference
Descript ion
Current
0 I.M AX
Arm I Limit
Limit s
Braking
1 P LUG Dir Change
Levels
2 ACCEL. Accelerat or Accel
Creep
3 CREEP
Creep Speed
Speed
Bypass
4 BYP ASS
M axim um
5 SP EED
Max. Speed
Speed
Cut back
6 SP EED1 Cut Spd 1
Speed 1
Cut back
SP EED2 Cut Spd 2
7
Speed 2
M ot or
I Cubed
8 F.W EAK
Set up Lower Limit
P ower St eer
T IM ER
9 P. Steer Timer
T im er
Seat Swit ch
10 SEAT Seat Delay
Delay
Additional
11 X2 Roll-off
P ersonalit ies
System
12 X3 Chop Select
Set up
X4 Fault Log
13 System Status
Speed
14 X5
Est im ate
System
BAT T
15 Battery Voltage
Volt ages
M ot or
16 M OT OR (V) Arm. Voltage
Volt ages
M ot or
17
M OT OR (A)
Arm. Current
Current s
Heat sink
18 T EMP Temperature
T em perat ure
19 T est M enu
T EST AccelDem
MillipaK 4QPM Controller Manual
1 2 3 4 5
(18) (19) (20) (21)
T OP
Neutral Foot brake
Drive Decel Dir Decel Neut. Decel Accel Zero V Accel Full V
Delay
Rev Speed
I Cubed
Upper Limit
Line Dropout
W alk Speed Belly Delay P SS P SS T imer
Ramp Up
Seat Cuts
SRO Enable Control Mode Roll-Off
Brae
Pump
Analogue System
Voltage
Inputs
Cap. Voltage
P oint P oint
A1 A2
Q2 Q4
FET Voltage FET Voltage
Voltage Voltage
Max Clear Max
Temperature Temperature
Accel Aux.
Aux. Demand Voltage Digital 1 Switch Digital 2 Switch
Voltage
T OP
6 7
xxx
Service Level Access
xxx Engineering Level Access
xxx All Adjust Level Access
8 9 10
Low V
SRO Delay Low V St art High V St art
Timer
Cutout
Rev Spd FS1 Recyc. Seq Dir SW M ot or P rot Line Dropout
Digital 3 Switch Digital 4 Switch Digital 5 Switch Digital 6 Switch
Page 63
Map for 4Q Controller System Version UK0076 - 19th June, 2002
Navigation
T he operat or m oves t hrough the Calibrat or M ap by pressing t he SELECT key. T he solid line shows t he pat h t he
t hrough th e menu st ruct ure when the SELECT key is pressed.
In Service Mode (no P assword ent ered) only t he it ems shown wit h a t hick solid border are display ed. W hen the
next item is hidden (Engineering or All adjust access only), t he calibrat or mov es on t he next displayable item .
It em s which are not configured will also be hidden, ie the bypass it em s will not be displayed if t he bypass
cont act or is not con figured.
In Engineering M ode (P asswo rd ent ered) the it ems shown with a solid border are displayed. W hen t he next item
is hidden (All adjust access only), the calibrator moves on t he next displayable item . It ems which are not
configured will also be hidden.
In All Adjust Mode (P assword ent ered) all t he it ems (solid and dashed borders) are displayed.
Direction
By default , t he Calibrator moves from left t o right t hrough t he m en u structure. If the operat or presses and holds
t he '+' and '-' keys for m ore than 1 second t he navigat ion direction changes and t he Calibrat or will m ove from
right t o left t hrough the menu st ruct ure. T he direction can be rest ored by holding t he '+' and '-' keys for 1 second
again.
T he direction is indicated by t he LED on t he Bar Graph. If t he LED is lit steadily, t he direct ion is from left t o
right , else if t he LED is flashing the direction is from right to left .
Information Items
T he T est m enu only shows in format io n item s th at cannot be modified. T he operator can move up
and down t he m enu using t he '+' and '-' keys. As before, it ems wit h a dashed border are only displayed in All
Adjust Mode. If t he Operator presses the SELECT key the Calibrat or m oves to t he next m enu.
Item Identification
T he operat or can identify t he current it em by holding down the '+' and '-' keys. For example, holding down the
'+' and '-' k eys on t he High V Cut out personalit y will display 11.09 (M enu 11 (I.M AX is m enu 0), Item 9). T he
operator will use the User Manual t o identify t he personalit y from t he ID.
11
12 13 14 15
High V
FBrake FBrake Full
Zero
Cutout
High Speed Power Steer FBrake
Accel Char. Belly Style
Mode Trigger
Priority
S/ Ser Ser Ser
W Version S/W Revision No. Date No. ID1 No. ID2
Calibrator Map
16 17
Buzzer Alarm Digit al I/O
Pers Checksum
13/08/03