Senlan Hope800 Series Manual page 87

0.00~650.00Hz
Setting Note: Multistep frequencies 32~48 are only used for the simple PLC operation. Each
range multistep frequency's default setting is its respective serial number, for example, the default
setting of the multistep frequency 3 is 3.00Hz.
F4-17=0: The multistep frequency is selected by the combination of the binary codes for the multistep
frequency selects 1~5(see Section 6.5), for example, if X1~X5 are set to multistep frequency selects 1~5
respectively, the frequency selecting table will be as follows, where "0" means invalid and "1" means valid.
X5 X4 X3 X2
0 0 0 0
0 0 0 0
0 0 0 1
0 0 0 1
0 0 1 0
0 0 1 0
0 0 1 1
0 0 1 1
0 1 0 0
0 1 0 0
0 1 0 1
0 1 0 1
0 1 1 0
0 1 1 0
0 1 1 1
0 1 1 1
F4-17=1: The multistep frequency selects 1~8(see Section 6.5) directly correspond to the multistep
frequencies 1~8 respectively, for example, if X1~X8 are set to multistep frequency selects 1~8, the frequency
selecting table will be as follows, where "0" indicates invalid, "1" indicates valid and "-" indicates any state.
X8 X7
0 0
- -
- -
- -
X1 Result of selection
Reference frequency for
0
common operation
Multistep frequency 1
1
(F4-18)
Multistep frequency 2
0
(F4-19)
Multistep frequency 3
1
(F4-20)
Multistep frequency 4
0
(F4-21)
Multistep frequency 5
1
(F4-22)
Multistep frequency 6
0
(F4-23)
Multistep frequency 7
1
(F4-24)
Multistep frequency 8
0
(F4-25)
Multistep frequency 9
1
(F4-26)
Multistep frequency 10
0
(F4-27)
Multistep frequency 11
1
(F4-28)
Multistep frequency 12
0
(F4-29)
Multistep frequency 13
1
(F4-30)
Multistep frequency 14
0
(F4-31)
Multistep frequency 15
1
(F4-32)
X6 X5 X4
0 0 0
-
- -
-
- -
- - -
X5 X4 X3 X2
1 0 0 0
1 0 0 0
1 0 0 1
1 0 0 1
1 0 1 0
1 0 1 0
1 0 1 1
1 0 1 1
1 1 0 0
1 1 0 0
1 1 0 1
1 1 0 1
1 1 1 0
1 1 1 0
1 1 1 1
1 1 1 1
X3 X2 X1
0 0 0
- - 1
- 1 0
1 0 0
6 Parameter Description
X1 Result of selection
Multistep frequency 16
0
(F4-33)
Multistep frequency 17
1
(F4-34)
Multistep frequency 18
0
(F4-35)
Multistep frequency 19
1
(F4-36)
Multistep frequency 20
0
(F4-37)
Multistep frequency 21
1
(F4-38)
Multistep frequency 22
0
(F4-39)
Multistep frequency 23
1
(F4-40)
Multistep frequency 24
0
(F4-41)
Multistep frequency 25
1
(F4-42)
Multistep frequency 26
0
(F4-43)
Multistep frequency 27
1
(F4-44)
Multistep frequency 28
0
(F4-45)
Multistep frequency 29
1
(F4-46)
Multistep frequency 30
0
(F4-47)
Multistep frequency 31
1
(F4-48)
Result of selection
Reference frequency for
common operation
Multistep frequency 1
(F4-18)
Multistep frequency 2
(F4-19)
Multistep frequency 3
83