Multitech MultiVOIP MVP210 User Manual page 64

Field Name
Country Selection for
Built-In Modem
(not applicable to
MVP210)
User Defined Tones fields
Type column
Frequency 1
Frequency 2
Gain 1
Gain 2
Cadence
(ms) On/Off
Setting Custom Tones and Cadences (optional). The Regional Parameters dialog box has a secondary dialog
box that allows you to customize DTMF tone pairs to create unique ring-tones, dial-tones, busy-tones or
"unobtainable" tones or "re-order" tones or "survivability" tones for your system. This screen allows the user to
specify tone-pair attributes that are not found in any of the standard national/regional telephony toning schemes.
To access this customization feature, click on the Custom button on the Regional Parameters screen. The
"Custom" button is active only when "Custom" is selected in the Country/Region field.
Field Name Values
Tone Pair dial tone, busy tone
ring tone, 'unobtainable'
tone, survivability tone,
re-order tone
Tone Pair Values
Frequency 1 Frequency in Hertz
Frequency 2 Frequency in Hertz
Gain 1 +3dB to –31dB
and "mute" setting
Gain 2 +3dB to –31dB
and "mute" setting
Cadence 1 integer time value in
milliseconds; zero value
for dial-tone indicates
continuous tone
Cadence 2 duration in milliseconds
Cadence 3 duration in milliseconds
Cadence 4 duration in milliseconds
Multi-Tech Systems, Inc.
"Regional Parameter" Definitions (continued)
Values Description
country name MultiVOIP units operating with the X.06 software release (and above)
include a built-in modem. The administrator can dial into this modem to
configure the MultiVOIP unit remotely. The country name values in this
field set telephony parameters that allow the modem to work in the listed
country. This value may be different than the Country/Region value. For
example, a user may need to choose "Europe" as the Country/Region
value but "Denmark" as the Country-Selection-for-Built-In-Modem value.
Name of supervisory tone pair. Cannot be same as name of any
alphanumeric
standard tone pair.
name
Freq. in Hertz Lower frequency of pair.
Freq. in Hertz Higher frequency of pair.
+3dB to –31dB Amplification factor of lower frequency of pair.
and "mute" This applies to any supervisory tones that the MultiVOIP outputs as
setting audio to the FXS, FXS, or E&M port. Default: "Mute"
+3dB to –31dB Amplification factor of higher frequency of pair.
and "mute" This applies to any supervisory tones that the MultiVOIP outputs as
setting audio to the FXS, FXO, or E&M port. Default: "Mute"
n/n/n/n On/off pattern of tone durations used to denote supervisory tones
four integer time specified by user. Supervisory tones relate to answering and
values in disconnection of calls. Although most cadences have only two parts (an
milliseconds; "on" duration and an "off" duration), some telephony cadences have four
(zero value parts. Most cadences, then, are expressed as two iterations of a two-
indicates part sequence. Although this is redundant, it is necessary to allow for
continuous tone) expression of 4-part cadences.
Custom Tone-Pair Settings Definitions
Description
Identifies the type of telephony signaling tone for which frequencies are
being specified.
About Defaults: US telephony values are used as defaults on this screen.
Frequency of lower tone of pair.
This outbound tone pair enters the MultiVOIP at the input port.
Frequency of higher tone of pair.
This outbound tone pair enters the MultiVOIP at the input port.
Amplification factor of lower frequency of pair. This figure describes
amplification that the MultiVOIP applies to outbound tones entering the
MultiVOIP at the input port. Default: -16dB
Amplification factor of higher frequency of pair. This figure describes
amplification that the MultiVOIP applies to outbound tones entering the
MultiVOIP at the input port. Default: -16dB
On/off pattern of tone durations used to denote phone ringing, phone busy,
dial tone ("0" indicates continuous tone) survivability and re-order.
Cadence 1 is duration of first period of tone being "on" in the cadence of
the telephony signal.
Cadence 2 is duration of first "off" period in signaling cadence.
Cadence 3 is duration of second "on" period in signaling cadence.
Cadence 4 is duration of second "off" period in the signaling cadence.
Chapter 4: Configuring your VOIP
64