Teledyne T400 User Manual page 15

Photometric ozone analyzer with numaview software

Table of Contents

FIGURES

Figure 2-1. Front Panel Layout .................................................................................................................................21

Figure 2-2. Rear Panel Layout .................................................................................................................................22

Figure 2-3. T400 Internal Layout - Top View with IZS Option .................................................................................24

Figure 2-4. Analog Output Connector ......................................................................................................................26

Figure 2-5. Current Loop Option Installed on Motherboard .....................................................................................27

Figure 2-6. Status Output Connector for Digital Outputs..........................................................................................29

Figure 2-7. Control Input Connector .........................................................................................................................30

Figure 2-8. Concentration Alarm Relay ....................................................................................................................31

Figure 2-9. Rear Panel Connector Pin-Outs for RS-232 Mode ................................................................................32

Figure 2-10. Default Pin Assignments for CPU COM Port connector (RS-232) ......................................................33

Figure 2-11. Jumper and Cables for Multidrop Mode ...............................................................................................35

Figure 2-12. RS-232-Multidrop PCA Host/Analyzer Interconnect Diagram .............................................................36

Figure 2-13. Gas Line Connections for the T400 Analyzer - Basic Configuration ...................................................39

Figure 2-14. Gas Line Connections for the T400 Analyzer with Zero/Span Valve Option (OPT 50A) .....................41

Figure 2-15. Gas Line Connections for the T400 Analyzer with IZS Option (OPT 50G) ..........................................43

Figure 2-16. Gas Line Connections when the T400 Analyzer is Located in the Room Being Monitored ................44

Figure 2-17. Gas Line Connections when the T400 Analyzer is Monitoring a Remote Location .............................45

Figure 2-18. T400 Pneumatic Diagram - Basic Unit ................................................................................................46

Figure 2-19. T400 Pneumatic Diagram with Zero/Span (ZS) Option (OPT50A) ......................................................47

Figure 2-20. T400 Pneumatic Diagram with Internal Zero/Span (IZS) Option (OPT50G) .......................................48

Figure 2-21. Status Screens at Startup ....................................................................................................................49

Figure 2-22. Home Page Example ...........................................................................................................................50

Figure 2-23. Viewing Active Alerts Page ..................................................................................................................50

Figure 2-24. Sample Dashboard Page .....................................................................................................................51

Figure 2-36. DAS Download Page ...........................................................................................................................63

Figure 2-42. Homescreen Configuration ..................................................................................................................69

Figure 2-43. Digital Outputs Setup ...........................................................................................................................70

Figure 2-44. Analog Output Configuration Example .................................................................................................71

Figure 2-45. Analog Outputs Group Calibration Screen...........................................................................................72

Figure 2-46. Analog Outputs Manual Calibration Screen (AOUT2 Example) ..........................................................72

Figure 2-47. Setup for Checking / Calibrating DCV Analog Output Signal Levels ...................................................73

Figure 2-48. Setup for Checking / Calibration Current Output Signal Levels ...........................................................74

Figure 2-49. Alternative Setup Using 250Ω Resistor for Checking Current Output Signal Levels ...........................75

Figure 2-50. Communications Configuration, Network Settings ..............................................................................78

Figure 2-51. Configuration Transfer .........................................................................................................................79

Figure 3-1. MODBUS via Ethernet ...........................................................................................................................82

Figure 3-2. MODBUS via Serial Communication (example) ....................................................................................83

Figure 3-3. Serial Communication, Setting Hessen Protocol ...................................................................................84

Figure 4-1. Multi-Point Calibration Page ..................................................................................................................90

Figure 4-2. Zero and Span Calibration Screens .......................................................................................................91

Figure 4-3. Auto Cal Page ........................................................................................................................................93

Figure 5-1. Report Generation Page ......................................................................................................................101

Figure 5-2. Remote Update Page...........................................................................................................................102

Figure 5-3. Manual Update Page (and other utilities).............................................................................................102

Figure 5-4. Touchscreen Calibration Page .............................................................................................................103

Figure 5-5. Time Zone Change Requirements .......................................................................................................104

Figure 5-6. Replacing the Particulate Filter ............................................................................................................105

Figure 5-7. Replacing the IZS Zero Air Scrubber ...................................................................................................106

Figure 5-8. Optical Bench - Lamp Adjustment/ Installation ...................................................................................110

Figure 5-9. O

Generator UV Lamp ........................................................................................................................112

Figure 5-10. Location of O

Generator Adjustment Pot ..........................................................................................113

Figure 5-11. CPU Status Indicator..........................................................................................................................118

083730400A DCN8130

Teledyne API - Model T400 O

Analyzer

xiii

Table of Contents