Page 2 Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. Symbol, the Symbol logo and Spectrum24 are registered trademarks of Symbol Technologies, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by LXE, Inc. is under license.
Page 3 Appendix B – Technical Specifications Note: A complete revision history is included in Appendix B, “Technical Specifications”. Revision Notice VX5 Reference Guide Explanation Added footnote to “Overview” section. Revised “Drive C Directory Structure”. Revised “Wavelink Avalanche Enabler Configuration” for Avalanche Mobility Center.
Page 5: Table Of Contents
System Memory...16 Upper Memory Block ...16 Flash BIOS...16 Video Subsystem ...17 Power Input...17 Uninterruptible Power Supply...17 Backup Battery...17 PCMCIA Slots ...17 Power Management ...17 Physical Controls... 18 On/Off Switch...18 External Connectors ... 19 E-EQ-VX5RG-G Table of Contents AYOUT VX5 Reference Guide...
Page 6 Spread Spectrum RF Antenna Connector Pin ...34 Vehicle Remote Antenna Mount...34 Internal USB Port ...35 Pinout ...35 The Keyboards ... 36 The 95-key QWERTY Keyboard with Pointing Device ...37 Key Maps ...37 NumLock and the VX5... 37 VX5 Reference Guide Table of Contents E-EQ-VX5RG-G...
Page 7 Table of Contents CapsLock, Scroll Lock and the VX5 ... 37 Keyboard Backlight...38 The 60-key QWERTY Keyboard ...39 IBM 3270 Keypad Overlay ...39 IBM 5250 Keypad Overlay ...39 Key Maps ...40 Unused Key Functions ...40 NumLock and the VX5 ...40 Keyboard Backlight...40...
Page 8 VMT Keyboard Backlighting ... 74 Microsoft Windows Setup and Configuration ... 74 Microsoft Windows License Agreement (First Boot) ...75 Microsoft Windows 2000...75 Microsoft Windows XP...75 Drive C Directory Structure ...76 Software Loaded on Drive C...76 VX5 Reference Guide Table of Contents E-EQ-VX5RG-G...
Page 9 Step 3 – Configuring the Screen Control Application...83 Operation ...83 Error and Status logging ...84 Uninstalling the Application...84 VX5 Delivered with No Hard Drive ... 85 VX5 Delivered with No OS ... 86 Installing Microsoft Windows with Norton Ghost ...86 Microsoft Windows 2000...86 Microsoft Windows XP...88...
Page 10 Setting EAP/TLS Parameters... 152 Validating the Server Certificate... 154 Cisco Radio ... 157 Configuration...157 Profile Properties Screens ...160 Encryption...164 Static WEP ...165 LEAP ...166 Diagnostics ...168 Updating Firmware...169 WPA for the Cisco Radio ...170 VX5 Reference Guide ONFIGURATION Table of Contents E-EQ-VX5RG-G...
Page 11 Startup Problems ... 214 Bypassing Microsoft Windows Startup ...215 Verifying Boot Order...216 Setting System Time and Date ...216 Hardware Problems ... 217 Power Source ...217 Keyboard...218 Display...218 Hard Disk Drive...218 PCMCIA Cards...219 Memory Conflicts...219 IRQ Assignments...220 Optional Devices ...221 E-EQ-VX5RG-G VX5 Reference Guide...
Page 12 Environmental Specifications... 238 Display Specifications ...239 UPS Battery Pack Specifications...239 Radio Specifications... 240 Summit CF 2.4GHz ...240 PCMCIA Cisco 2.4GHz Type II ...240 PCMCIA Symbol 11Mb 2.4GHz Type II...240 Revision History... 241 NDEX VX5 Reference Guide Table of Contents E-EQ-VX5RG-G...
Page 13 Figure 2-9 D9 Male Connector ...24 Figure 2-10 PS/2 Keyboard Connector...25 Figure 2-11 PS/2 Mouse Connector...25 Figure 2-12 VX5 USB Connector and External USB Adapter Cable Connector...26 Figure 2-13 VX5 Ethernet/USB Dongle Cable...27 Figure 2-14 D15 Female Connector...27 Figure 2-15 Dongle Cable USB Port ...28 Figure 2-16 Dongle Cable Ethernet Port...29...
Page 14 Figure 2-46 Power Adapter Cable, VX1/2/4 to VX5...57 Figure 2-47 Fuse Replacement ...58 Figure 3-1 DIP Switch Location ...73 Figure 3-2 Touchscreen Calibration, Targets ...78 Figure 3-3 Touchscreen Calibration, Save and Exit ...78 Figure 3-4 Touch Panel Configuration ...79 Figure 3-5 Loop Back Cable...81 Figure 3-6 Screen Blanking Installation ...82...
Page 15 Figure 4-81 Cisco ACU ...187 Figure 4-82 Cisco Profile Manager...187 Figure 4-83 System Parameters ...188 Figure 4-84 Network Security ...188 Figure 4-85 LEAP Settings...189 Figure 4-86 Select Profile ...189 Figure 4-87 LEAP User Name and Password...190 E-EQ-VX5RG-G VX5 Reference Guide...
Page 16 Figure 4-117 Windows Wireless Network Properties ...212 Figure A-1 95-Key VMT QWERTY Keyboard ...229 Figure A-2 60-Key VMT QWERTY Keyboard ...230 Figure A-3 IBM 3270 Specific Keypad...235 Figure A-4 IBM 5250 Specific Keypad...235 VX5 Reference Guide Table of Contents E-EQ-VX5RG-G...
Page 17: Chapter 1 Introduction
Please refer to Chapter 3 “System Configuration”, section titled “Microsoft Windows License Agreement (First Boot)” for instruction. The “VX5 User’s Guide” is directed toward the VX5 user. It is delivered on the LXE Documentation CD. It contains safety warnings, descriptions of the controls and connectors, instruction on installing antennas, and day to day operation.
Page 18: When To Use This Guide
Use this guide as you would any other source book -- reading portions to learn about the VX5, and then referring to it when you need more information about a particular subject.
Page 19: Document Conventions
Keyword that indicates a potentially hazardous situation, which, if not avoided, WARNING could result in death or serious injury. Keyword that indicates an imminent hazardous situation, which, if not avoided, DANGER will result in death or serious injury. E-EQ-VX5RG-G VX5 Reference Guide...
Page 20: Quick Start
1. Install Vehicle Mounting Bracket (and keyboard mounting bracket) on vehicle. 2. Secure VX5 in Mounting Bracket Assembly. 3. Connect power cable to the VX5. The power cable can also be connected to a UPS battery pack, which is then connected to the VX5.
Page 21: Figure 1-3 Vx5 Components, Front
Components E-EQ-VX5RG-G Figure 1-3 VX5 Components, Front Power LED Power Switch Brightness Increase Brightness Decrease Figure 1-4 VX5 Control Panel Speakers Control Panel (See Following Illustrations for Detail) VX5 Reference Guide...
Page 22: Figure 1-5 Vx5 Components, Bottom
PRODUCT OF U.S.A. U.S. PATENT 5862393 AUDIO INPUT: 12-80VDC 6A 72W COM2/3 KEYBOARD / ETHERNET / MOUSE T10A, 125V Figure 1-5 VX5 Components, Bottom Components COM1/Scanner Connector COM2 Connector Keyboard/Mouse Connector Ethernet/USB Cable Connector Fuse Audio Connector...
Page 23: Data Entry
The keyboard is used to manually input data that is not collected otherwise. Almost any function that a full sized computer keyboard can provide is duplicated on the LXE VMT keyboard but it may take a few more keystrokes to accomplish a keyed task.
Page 24: Touchscreen Entry
(touch) of up to 4 oz. of pressure. The touch screen can be used in conjunction with the keyboard and scanner and an input/output device connected to one of the VX5’s serial ports. • Touch the stylus to the field of the data entry form to receive the next data feed.
Page 25: Virtual Keyboard
When the virtual keyboard is displayed, the physical keyboard is still active, if attached. Therefore it is possible to input data from both keyboards. E-EQ-VX5RG-G ® software provides a virtual keyboard on the touchscreen. To start the Figure 1-6 Virtual Keyboard, Typical Configuration VX5 Reference Guide...
Page 26: Getting Help
LXE website. Contact your LXE representative to obtain the LXE Manuals CD. You can also get help from LXE by calling the telephone numbers listed on the LXE Manuals CD, in the file titled “Contacting LXE”. This information is also available on the LXE website www.lxe.com.
Page 27: Accessories
Bracket, U Style, VX5 Bracket, U Style w/ Integrated Keyboard Mount, VX5 Kit, VXX U-Bracket to VX5 Adapter Kit, VXX U-Bracket to VX5 Adapter w/ Keyboard Mount Bracket, RAM Mount, VX5 Bracket, Combo RAM VMT Mount w/ Keyboard Mount, VX5...
Page 28 Cable 9000A075CBLUSBHCETH ( ) can be used in place of 9000A071CBLD15USBETH. However, the USB-Client Adapter port is not supported when 9000A075CBLUSBHCETH is used with the VX5. Power Cables Cable, Input Power, 12 FT, VX5 VX6 VX7 Adapter Cable, VX1 VX2 VX4 Power Cable to VX5 VX6 VX7...
Page 29 (above part is not RoHS compliant) 8310A333SCNRL12D9FLT (above part is not RoHS compliant) 8320A326SCNRPWRXLR8DA9F 8320A326SCNRPWRXLR8DA9F-R 8320A327SCNRPWRXLR12DA9F (above part is not RoHS compliant) 8320A332SCNRX8D9FLT (above part is not RoHS compliant) 8320A333SCNRX12D9FLT (above part is not RoHS compliant) 8510A326SCNRFZYDA9F 8510A326SCNRFZYDA9F-R 8520A326SCNRERDA9F-R VX5 Reference Guide...
Page 30 Manuals and Accessories VX5 Reference Guide E-EQ-VX5RG-G...
Page 31: Chapter 2 Physical Description And Layout
Chapter 2 Physical Description and Layout Hardware Configuration System Hardware The VX5 hardware configuration is shown in the following figure. E-EQ-VX5RG-G Any Type I, II or III PCMCIA Card Antenna Connector Slot 0 & Slot Slot 1 Serial Keyboard/ Connector...
Page 32: Central Processing Unit
Central Processing Unit The LXE VX5 contains an Intel Pentium III 933 MHz CPU. AT Compatible Core Logic The LXE VX5 utilizes AT-compatible core logic. The VX5 supports the following I/O components: • Two 9-pin RS-232 serial ports configured as: Note: •...
Page 33: Video Subsystem
Blanking Service” in Chapter 3, “System Configuration” for details. Power Input Vehicle power input for the VX5 is 12V to 80V DC nominal and is accepted without the need to perform any manual operation within the VX5. If 12V to 60V DC power is not available – for example, in an office environment – an optional external Universal Input Power Supply can be used to convert AC wall power to an appropriate DC level.
Page 34: Physical Controls
Physical Controls On/Off Switch The power (on/off) switch is a push button switch located on the front control panel of the VX5. The switch is a momentary switch. If the VX5 is Off, pressing the power switch turns the VX5 On.
Page 35: External Connectors
“COM2” or “COM2/3”. Other external connectors are located as follows: • Antenna connectors are located on the top of the VX5. VX5’s can be configured for a single antenna or dual antennas. • A USB port is available inside the access panel.
Page 36: Scanner Serial Connector (Com1)
Note: Pin 9 of the COM port can be switched between +5V and RI. See Chapter 3: “System Configuration” section titled “Serial Port Pin 9”. VX5 Reference Guide Figure 2-3 Scanner Serial Connector (COM1) Description Data Carrier Detect – Input Receive Data –...
Page 37: Printer/Pc Serial Connector (Com2)
Transmit Data – Output Data Terminal Ready – Output Signal/Power Ground Data Set Ready – Input Request to Send – Output Clear to Send – Input Ring Indicator – Input (default) Bar Code Scanner Power – 400mA max Chassis Ground VX5 Reference Guide...
Page 38: Technical Specifications - Screen Blanking Cable
(for example, via a switch on the accelerator pedal of the fork truck). All other pins on the connector must be left unconnected. If pins 7 and 8 do not provide continuity (or the cable is removed), the VX5 screen remains blank. Serial cable:...
Page 39: Keyboard/Mouse Connector
An LXE VMT keyboard without integrated pointing device • A dongle cable providing PS/2 connections for a standard PS/2 keyboard and mouse. Figure 2-7 VX5 Keyboard Connector and External Keyboard Cable Connector The +5V supply available from the connector is current limited at 400mA. Pinout...
Page 40: Ps/2 Keyboard/Mouse Dongle Cable
PS/2 Keyboard/Mouse Dongle Cable The PS/2 keyboard/mouse dongle cable allows a standard PS/2 keyboard and/or mouse to be attached to the VX5. The PS/2 connectors on the dongle cable are labeled for keyboard and mouse. D9 Male Connector Pinout Signal...
Page 41: Ps/2 Keyboard Connector
Description Keyboard Data Not Connected System Ground Keyboard Power, 5V Keyboard Clock Not Connected Chassis Ground Figure 2-11 PS/2 Mouse Connector Description Mouse Data Not Connected System Ground Keyboard Power, 5V Mouse Clock Not Connected Chassis Ground VX5 Reference Guide...
Page 42: Ethernet/Usb Connector
Ethernet/USB Connector The VX5 Ethernet/USB connector accepts a dongle cable that provides a USB port and an Ethernet port. The connector is shown below. Figure 2-12 VX5 USB Connector and External USB Adapter Cable Connector Pinout Signal USB2N_A – –...
Page 43: Ethernet/Usb Dongle Cable
DGND – RJ45_45 RJ45_78 5V_USB_23 – – Shell CGND E-EQ-VX5RG-G Figure 2-13 VX5 Ethernet/USB Dongle Cable Figure 2-14 D15 Female Connector Description USB D – Not Connected Not Connected Receive + Receive – USB D + USB Power Return Not Connected...
Page 44: Usb Connector
USB Connector Pinout Signal 5V_USB_23 USB2N_A USB2P_A DGND Shell CGND VX5 Reference Guide Figure 2-15 Dongle Cable USB Port Description USB Power, Current Limited USD D – USB D + USB Power Return Chassis Ground External Connectors E-EQ-VX5RG-G...
Page 45: Rj45 Connector
External Connectors RJ45 Connector Pinout Signal – – – – E-EQ-VX5RG-G Figure 2-16 Dongle Cable Ethernet Port Description Transmit + Transmit – Receive + Not Connected Not Connected Receive – Not Connected Not Connected VX5 Reference Guide...
Page 46: Audio Connector
Audio Connector The VX5 audio connector accepts a headset with a 2.5mm plug, such as a mono telephone headset with microphone. Figure 2-17 VX5 Audio Jack for External Speaker or Headphones Note: The VX5 is not configured for standard PC speakers.
Page 47: Power Supply Connector
The VX5 internal power supply can accept DC input voltages in the range of 12 to 80 Volts. Pinout UPS Battery Positive (+) UPS Battery Negative (–)
Page 48: Ups Battery Pack Connectors
Pinout Output Figure 2-20 The UPS Battery Pack Output Connector Pinout UPS Battery Positive (+) UPS Battery Negative (–) VX5 Reference Guide Figure 2-19 The UPS Battery Pack Input Connector Signal DC Positive (+) Not used Chassis Ground Not used DC Negative (–)
Page 49: Ups Battery Extension Cable Connectors
Figure 2-22 The UPS Battery Extension Cable Output Connector Pinout UPS Battery Positive (+) UPS Battery Negative (–) E-EQ-VX5RG-G Signal DC Positive (+) Chassis Ground DC Negative (–) Signal DC Positive (+) Chassis Ground DC Negative (–) VX5 Reference Guide...
Page 50: Antenna Connector
VX5’s equipped with a radio require an external antenna. A VX5 without a radio does not use an antenna. Some VX5’s may be equipped with a dual antenna option. For these VX5’s, an external antenna must be connected to each antenna connector.
Page 51: Internal Usb Port
An internal USB port can be accessed by removing the access panel cover. This port conforms to USB 1.0 specifications. Pinout Signal 5V_USB_23 USB2N_A USB2P_A DGND Shell CGND E-EQ-VX5RG-G Figure 2-25 Dongle Cable USB Port Description USB Power, Current Limited USD D – USB D + USB Power Return Chassis Ground VX5 Reference Guide...
Page 52: The Keyboards
• A standard PS/2 keyboard via an adapter cable attached to the “Keyboard/MOUSE” port on the VX5. The adapter cable also provides a connector for a PS/2 mouse. • A software keyboard, or virtual keyboard, can be displayed on the touch screen. The virtual keyboard can be used in place of, or in addition to, a physical keyboard.
Page 53: The 95-Key Qwerty Keyboard With Pointing Device
Designed for ease of use with Windows operating systems, the 95-key keyboard with pointing device connects via a cable to the keyboard port on the VX5. Additional Windows keys (the Windows logo key and the Application key) and an integrated pointing device are provided for ease of use with Windows operating systems.
Page 54: Keyboard Backlight
“backlight” key in the upper right hand corner of the keyboard. Pressing the backlight key cycles the keyboard backlight through the levels of backlight intensity: • • Maximum intensity • Medium intensity • Low intensity. VX5 Reference Guide The Keyboards E-EQ-VX5RG-G...
Page 55: The 60-Key Qwerty Keyboard
IBM 3270 Keypad Overlay CTRL Attn SHIFT The 60-key keypad is available with an IBM 3270 overlay designed to allow the user to enter terminal emulator commands when running LXE’s RFTerm IBM 5250 Keypad Overlay CTRL Attn SHIFT The 60-key keypad is available with an IBM 5250 overlay designed to allow the user to enter terminal emulator commands when running LXE’s RFTerm...
Page 56: Key Maps
The hidden keys supported by the VX5 are listed in Appendix A, “Key Maps”. Unused Key Functions There are several key functions on the 60-key keyboard that are not used on the VX5. These include: •...
Page 57: Keyboard Leds
The Keyboards Keyboard LEDs The VX5 keyboard has three (2) LED indicators. CAPS LED This LED indicates the state of the keyboard CapsLock mode. If CapsLock is enabled this LED is illuminated green. When CapsLock is off, the LED is dark.
Page 58: Secondary Keys Led
> and <Q> to type the “!” key. Press <2 > and <BkSp> to enter the Insert (Ins) mode. VX5 Reference Guide > key followed by the superscripted key. Figure 2-33 The Secondary Key > state is enabled until another key is pressed. The <2 The Keyboards >...
Page 59: Control Keys
The Keyboards Control Keys The VMT keyboard has several control keys. Because of the construction of the VX5 and the Microsoft Windows operating system, many of the Control Keys are not used on the VX5. Note: The 2 functions of the <F4> and <F5>keys are not used as the display brightness is adjusted via the buttons on the control panel.
Page 60: General Windows Keyboard Shortcuts
General Windows Keyboard Shortcuts Use the keyboard shortcuts in the chart below to navigate with any VX5 keyboard. These are standard keyboard shortcuts for Windows applications. Press these keys … CTRL + C CTRL + X CTRL + V CTRL + Z...
Page 61: Ps/2 Keyboard/Mouse
The Keyboards PS/2 Keyboard/Mouse A standard PS/2 keyboard and mouse can be attached to the VX5 using the appropriate dongle cable. The dongle cable attaches to the VX5 and provides two PS/2 connectors, one labeled “Keyboard” and one labeled “Mouse”. Please refer to documentation provided with the PS/2 keyboard and mouse for more information on their operation.
Page 62: The Display
Always use the point of the stylus for tapping or making strokes on the display. Never use an actual pen, pencil or sharp object to write on the touch screen. An extra or replacement stylus may be ordered from LXE. See the “Accessories” section for the stylus part number.
Page 63: Install/Remove Touchscreen Protective Film
Factory Default Settings Install/Remove Touchscreen Protective Film LXE offers a replaceable touchscreen protective film to protect the touchscreen when the VX5 is used in an abrasive environment. How To Install Touchscreen Protective Film 1. Clean the touchscreen and protective film with a standard household cleaner such as Windex without vinegar or use Isopropyl Alcohol.
Page 64: Pcmcia/Cardbus And Ata Slots
PCMCIA/CardBus and ATA Slots The VX5 has two PCMCIA/CardBus slots and one ATA slot. The PCMCIA slots are stacked on top of each other and located on the right hand side of the opening. The ATA is located on the left hand side of the opening.
Page 65: Pcmcia Pinout
PCMCIA/CardBus and ATA Slots PCMCIA Pinout E-EQ-VX5RG-G Signal Signal 12V_RF_POWER -CDI -CE1 -CE2 n.c. or VS1# -IORD -IOWR RDY/-IREQ SLOT_VCC SLOT_VCC SLOT-VPP SLOT_VPP n.c. or VS2# RESET -WAIT -INPACK -REG BVD2/-SPKR BDV1/-STSCHG WP/A_-IOIS16 -CD2 VX5 Reference Guide...
Page 66: Install Pcmcia Cards
The tethered access panel cover is not shown in the illustration above. VX5 Reference Guide The LXE Model VX5 Vehicle Mount Computer is specifically for use with LXE Model Numbers 4830, 6726 and 6816 2.4GHz Type II PCMCIA radios. Substitution of other PCMCIA radios will void the FCC, Industry Canada and other international radio certifications for the Model VX5 Vehicle Mount Computer and is strictly prohibited.
Page 67: Figure 2-38 Summit Antenna Cable Connections
Cisco radio with single antenna – Connect antenna cable to right port, as shown below. • Cisco radio with dual antennas – Connect antenna cables to both ports. E-EQ-VX5RG-G Main Auxiliary Port Port Figure 2-38 Summit Antenna Cable Connections Left Port Figure 2-39 Cisco Antenna Cable Connections Right Port VX5 Reference Guide...
Page 68: Figure 2-40 Symbol 11Mb Antenna Cable Connections
9±1 inch pounds (1.016±.11 N/m). The screws must be fastened to 9 inch pounds each. The screws require a Phillips size 1 driver head. Re-connect the power cord/cable and turn the VX5 on. VX5 Reference Guide Port A...
Page 69: Ata Slot
ATA Slot The ATA slot is connected to the secondary IDE controller. The slot accepts a PCMCIA card or a compact flash card via a PCMCIA adapter. The VX5 must be powered down before inserting or removing an ATA card.
Page 70: Power Supply
AC to DC power input for the VX5 is delivered via an optional external power supply. See “External Power Supply”. Vehicle power input for the VX5 is 12V to 80V DC nominal and is accepted without the need to perform any manual operation within the VX5. See “Vehicle 12-80VDC Direct Connection.” An optional uninterruptible power supply (UPS) battery can be used with the vehicle DC power supply.
Page 71: Specifications
0 Amps min, 1.87 Amps max FCC, Part 15, Radio Frequency Devices, Class B. EN 55022 UL1950 and IEC 950 Specification see VX5 Environmental Specifications see VX5 Environmental Specifications Operates in a relative humidity of: 5 – 95% (non-condensing) Per IEC 801-1 VX5 Reference Guide...
Page 72: Vehicle 12-80Vdc Direct Connection
Note: Correct electrical polarity is required for safe and proper installation. Connecting the cable to the VX5 with the polarity reversed will cause the VX5’s fuse to be blown. See the following table for wire color-coding specifics. Wiring color codes for LXE supplied DC input power cabling:...
Page 73: Vx5 Input Power Specifications
LXE offers an adapter cable (part no. 9000A077CBLPWRADPTR) to adapt certain VX1, VX2 or VX4 DC power supplies to the VX5. Please read and follow all cautions in the “VX5 User’s Guide” to determine if your present power supply can be used with the VX5.
Page 74: Cmos Battery
This battery should only be changed by authorized service personnel. Fuse The VX5 uses a 100V, 10A time delay (slow blow), high current interrupting rating fuse that is externally accessible and user replaceable. Should it need replacement, replace with same size, rating and type of fuse –...
Page 75: Chapter 3 System Configuration
Chapter 3 System Configuration Introduction Like any personal computer, there are many aspects to the setup and configuration of the VX5. Much of the setup and configuration of the VX5 is dependent upon the optional features (both hardware and software) installed on the computer. Since the VX5 uses the Microsoft Windows Plug and Play operating system, much of the hardware setup is automatic.
Page 76: Windows Management Instrumentation
VX5 BIOS includes support for Windows Management Instrumentation (WMI). The information displayed by selecting Programs | Accessories | System Tools | System Information from the Windows Start Menu identifies the System Manufacturer as “LXE Inc.” and the System Model as “VX5”.
Page 77: Identifying Bios Revision
Unless otherwise noted, BIOS parameters in the following sections are present in both BIOS revisions. Accessing the BIOS Setup When you turn the VX5 on, the unit starts to boot. Watch the bootup sequence and when the following is displayed: Press F2 to Enter Setup Press the [F2] key.
Page 78: Bios Setup Default Values By Option
• Changed parameter values take effect when the VX5 reboots upon exiting BIOS Setup. If the VX5 does not automatically reboot upon exit, please reboot the VX5. • Many items, like Power Savings and Keyboard repeat rate/delay may be configured via the Microsoft Windows Control panel.
Page 79: Main Menu Options
Legacy Diskette (A and B) This option is used to indicate if a floppy disk drive is attached to the VX5. The VX5 does not have a provision for a standard floppy drive; however, a USB floppy may be attached to the USB interface cable.
Page 80: Primary And Secondary Master And Slave Drives
Default: Note: The secondary drive is the enabled ATA slot on the side of the VX5. This drive may be either a PCMCIA or Compact Flash (via PCMCIA adapter) ATA drive. Please see “ATA Secondary Drive” later in this chapter for more details.
Page 81: Advanced Menu Options
CMOS RAM when “Save and Exit” is selected and the BIOS Setup program closes. Changed and saved parameter values take effect after the VX5 is rebooted. Advanced Chipset Control Parameters in this menu have been selected for best performance from your VX5. Changes are not recommended. PCI Configuration Parameters in this menu have been selected for best performance from your VX5.
Page 82: Keyboard Features
Use this option to set NumLock at boot time. When NumLock is On, the keypad is locked in numeric mode. When NumLock is Off the numeric keys are inoperable. Whether NumLock at Boot is Off or On, no LED is illuminated on the VX5. Values:...
Page 83: I/O Device Configuration
Enabled Auto OS Cntrl Default: Note: There is no parallel port (LPT1) on a VX5. Disabling the LPT1 port allows IRQ7 to be used by other devices. E-EQ-VX5RG-G No PCI IDE device enabled. Primary PCI IDE enabled. Secondary PCI IDE enabled.
Page 84: Usb Port / Usb Host Controller
These parameters determine if the USB port is active. Available with BIOS revision MOD8R901 only. Values: Default: Note: The USB adapter cable must be attached to the VX5 to use the USB port. USB BIOS Legacy Support Enables support for USB keyboard and mice. Values: Default: Note: To boot from a USB floppy, USB BIOS Legacy Support must be enabled.
Page 85: Security
BIOS Setup Security This menu can be used to set security features as desired. Power BIOS power management is disabled in the VX5. management. Boot Floppy Check This parameter determines if the floppy drive is verified on boot. Disabling provides a faster boot.
Page 86: Boot Device Priority
PCI BEV PCI SCSI Bootable Add-in Cards Legacy Network Card This is the default boot order delivered with your VX5. Valid functions are: • Highlight a device and press <+> to move it up the list of devices. • Highlight a device and press <-> to move it down the list of devices.
Page 87: Onboard Lan Rpl Rom
Removable Devices Hard Drive ATAPI CD-ROM Drive Network Boot This is the default boot order delivered with your VX5. Valid functions are: • Highlight a device and press <+> to move it up the list of devices. • Highlight a device and press <-> to move it down the list of devices.
Page 88: Exit Menu Options
This option is used to reset the Setup values to the original, default values that were set at the factory, before suppliers or end users made changes. The next time the VX5 is turned on or rebooted, those saved values are in effect. change by selecting “Save and Exit.”...
Page 89: Serial Port Pin 9
Note: Torquing tool is not supplied by LXE. Turn the VX5 off and remove the power supply before opening the access cover located on the top of the VX5. Loosen the three (3) Phillips screws securing the access cover so the cover can be removed.
Page 90: Vmt Keyboard Backlighting
VMT Keyboard Backlighting 95-key Keyboard This LXE keyboard has keys that are backlit with LEDs. The backlight is manually controlled using the “backlight” key in the upper right hand corner of the keyboard. Pressing the backlight key cycles the backlight through the levels of backlight intensity: •...
Page 91: Microsoft Windows License Agreement (First Boot)
If you ordered multiple VX5’s, a separate key code decal is included for each VX5. Each key code is to be used on only one VX5. Be sure to store the key codes in a safe place. Pressing “Next” finishes the licensing/registration process.
Page 92: Drive C Directory Structure
• RFTerm Note: If your VX5 was ordered with the no OS option, please refer to “VX5 with No OS”, later in this chapter. The software installed on the VX5 is summarized below. Note: Due to the complex directory structure and System Registry under Microsoft Windows, software should not be removed manually.
Page 93: Microsoft Windows Configuration
Windows guides. Radio Software If a radio is ordered with a VX5, the VX5 is delivered with the radio software installed. Because the VX5 is uses a Microsoft Windows operating system, the radio installation includes Windows device drivers.
Page 94: Touchscreen
To save the new calibration settings, click on the Save & Exit button or press <Enter>. To discard the new calibration settings, click Cancel & Exit or press <Esc>. VX5 Reference Guide Figure 3-2 Touchscreen Calibration, Targets Figure 3-3 Touchscreen Calibration, Save and Exit...
Page 95: Configuring Right Click On The Touchscreen
Fujitsu Touch Panel (USB). Right click on this listing and select Disable from the menu. To enable the touchscreen, follow the same process, selecting Enable from the right click menu. E-EQ-VX5RG-G Figure 3-4 Touch Panel Configuration VX5 Reference Guide...
Page 96: Network Configuration
Please refer to Chapter 4, “Wireless Network Configuration” for details on configuring the 2.4 GHz wireless radio cards. Ethernet Connector When the VX5 is networked using the Ethernet connector, the VX5’s networking options are set via the Microsoft Windows Control Panel. The same networking configuration options are available as in a standard PC.
Page 97: Screen Blanking Utility
Screen Blanking Utility Screen Blanking Utility The VX5 can be configured to blank the display when the vehicle to which it is mounted is moving. When configured properly, the screen blanking feature provides a tamper resistant method to blank the vehicle screen.
Page 98: Step 2 - Uninstall Screen Control Service
Note: Earlier versions of the screen blanking utility ran as a Windows service. If an earlier version is installed on the VX5, it must be removed before installing the current version. To uninstall the service, from a command prompt type: C:\WINDOWS\Microsoft.NET\Framework\v1.1.xxxx\InstallUtil /u...
Page 99: Step 3 - Configuring The Screen Control Application
This prevents a general user from defeating the screen control application. Operation of the VX5 is affected while the screen is blank. Keyboard input is disabled and the display backlight is off. Input from the keypad, touchscreen or other device DOES NOT wake up the display.
Page 100: Error And Status Logging
Uninstalling the Application To uninstall the Screen Blanking application, select Start | Control Panel | Add or Remove Programs and select VX5 Screen Blanking VX5 Reference Guide To access the log, select Start | Control Panel |...
Page 101: Vx5 Delivered With No Hard Drive
Torque to 8.0±1 in/lb (0.9±.11 N/m). The VX5 accepts 2.5” IDE flash or rotating hard drives. 5. Insert the hard drive into the VX5. Slide the assembly into the opening from which the empty bracket was removed. Do not slide it all the way in.
Page 102: Vx5 Delivered With No Os
Additionally, a Microsoft Windows image can be created on a hard drive before it is installed in the VX5. See “VX5 Delivered with No Hard Drive” earlier in this chapter for information on installing a hard drive in the VX5.
Page 103 8. Once the image has been copied, power the VX5 down and remove the secondary drive. 9. Restart the VX5 and edit the BIOS to return the Primary IDE to the top of the boot order. 10. Save the change and reboot the VX5.
Page 104: Microsoft Windows Xp
TEAC USB floppy drive or equivalent bootable USB floppy drive. Note: Software Required • Norton Ghost 2002 or equivalent • Microsoft Windows image VX5 Reference Guide Not all USB floppy drives are bootable devices. VX5 Delivered with No OS E-EQ-VX5RG-G...
Page 105 “Out of box experience” process detailed earlier in this chapter. Please refer to “Microsoft Windows License Agreement” for more details. 11. Restart the VX5 and edit the BIOS to return the Primary IDE to the top of the list (to boot into Microsoft Windows).
Page 106: Installing Microsoft Windows Over A Network
This section details installing the operating system over the network. This procedure assumes the VX5 has a formatted blank hard drive installed as the Primary IDE drive. You will also need software to enable the PCMCIA slot in which the Ethernet card will reside. For this example, that software will be Enabler that is delivered with the Socket LP-E Ethernet card.
Page 107 VX5 Delivered with No OS 11. After connecting to the network, perform all necessary installations. 12. Restart the VX5 and edit the BIOS to return the primary IDE to the top of the boot order. 13. Save the change and reboot the VX5.
Page 108 ; semi-colon below and enter the preferred server name after ; the equal sign. ;preferred server = CONFIG.SYS DEVICE=HIMEM.SYS /testmem:off FILES=30 BUFFERS=20 DEVICE=a:\socketlp\enablelp.exe socket=1 LASTDRIVE=Z AUTOEXEC.BAT @echo off cd\socketlp ne2000 odipkt SET PCTCP=a:\socketlp\pctpc.ini ethdrv.exe VX5 Reference Guide VX5 Delivered with No OS membase=0xE8000 messages=enabled E-EQ-VX5RG-G...
Page 109: Using The Ethernet Port
8. When the message is displayed, press F12 to connect to the RIS server. 9. When the file transfer is complete, reboot the VX5 and enter the BIOS by pressing F2. 10. Set “Onboard LAN RPL ROM” to disabled. Return primary IDE to the top of the boot order list.
Page 110: Installing Microsoft Windows From A Cd
Installing Microsoft Windows From a CD This section details installing the Microsoft Windows XP operating system from a CD-ROM. This procedure assumes the VX5 has a formatted blank hard drive installed as the Primary IDE drive. Hardware Required • VX5 computer with at least 10GB of free space on the hard drive •...
Page 111: The Vx5 Drivers Cd-Rom
Do not install the radio card before the drivers are installed. The driver installation prompts for the radio card to be inserted at the applicable time. – This directory contains the radio driver and radio firmware for the VX5 with a Cisco \Win2K radio and Microsoft Windows 2000 operating system.
Page 112 \Win_2K Contains drivers for use with the Microsoft Windows 2000 operating system: – Provides the touchscreen driver used on the VX5. The drivers are loaded by \TouchScreen running FTSETUP.EXE. – This file provides an update to the display driver. \Display Provides a driver for the Cardbus controller under Windows 2000.
Page 113: Wavelink Avalanche Enabler Configuration
This is done by launching the Cisco ACU and accessing the “Select Profile” tab. From there, select the option “Use Another Application to Configure My Wireless Settings”. When the VX5 is rebooted, the Avalanche Enabler will be controlling the wireless settings.
Page 114: Stop The Enabler Service
There are three methods by which the Enabler on an LXE device can communicate with the Mobile Device Server running on the host machine. • Wired via a serial cable between the Mobile Device Server and the VX5 (only COM1 is supported for this connection on the VX5).
Page 115: Mobile Device Wireless And Network Settings
Avalanche Network Profile”. 6. Click the OK button to save the changes. 7. Reboot the device. The designation of the mobile device to the Avalanche Manager is VX5. See Also: “Using Wavelink Avalanche on LXE Windows Computers”. E-EQ-VX5RG-G VX5 Reference Guide...
Page 116: Enabler Configuration
Enabler Configuration Avalanche Icon File VX5 Reference Guide Wavelink Avalanche Enabler Configuration The Enabler user interface application is launched by clicking: either the Avalanche icon on the desktop or Taskbar selecting Avalanche from the Programs menu. The opening screen presents the user with the connection status and a navigation menu.
Page 117: File Menu Options
If changes were made on the Startup/Shutdown tab screen, then after entering the password, tap OK and the following screen is displayed: Change the option if desired. Tap the X button to cancel Exit. Tap the OK button to exit the Avalanche applet. E-EQ-VX5RG-G VX5 Reference Guide...
Page 118: Avalanche Update Settings
Access: Start | Avalanche | File | Settings Use these menu options to setup the Avalanche Enabler on the mobile device. LXE recommends changing and then saving the changes (reboot) before connecting to the network. Alternatively, the Mobile Device Server on can be disabled until needed (refer to the Wavelink Avalanche Mobility Center User’s Guide.
Page 119: Connection
Enter the IP Address or host name of the Mobile Device Server assigned to the mobile device. Indicates whether the Enabler should first check for serial port connection to the Mobile Device Server before checking for a wireless connection to the Mobile Device Server. VX5 Reference Guide...
Page 120: Execution
Auto-Execute Selection Select Auto-Execute App Delay before execution VX5 Reference Guide Wavelink Avalanche Enabler Configuration Figure 3-13 Execution Options (Dimmed) An application that has been installed with the Avalanche Mobility Center Console system can be run automatically following each boot.
Page 121: Server Contact
Reset the time on the mobile computer based on the time on the Mobile Device Server. Allows the administrator to configure the Enabler to contact the Mobile Device Server and query for updates at a regular interval beginning at a specific time. VX5 Reference Guide...
Page 122: Startup/Shutdown
Monitor for updates Monitor and launch update utility Program Shutdown (Continue or Stop monitoring) VX5 Reference Guide Wavelink Avalanche Enabler Configuration Figure 3-15 Startup / Shutdown Options When the device boots, do not launch the Enabler application and do not attempt to connect to the Mobile Device Server.
Page 123: Display
Half screen, Hidden or Full screen. Default is Half screen. On connect As is, Half screen, full screen, Locked full screen. Default is As is. Normal Half screen, Hidden or As is. Default is As is. E-EQ-VX5RG-G Figure 3-16 Window Display Options VX5 Reference Guide...
Page 124: Shortcuts
Configure shortcuts to other applications on the mobile device. Shortcuts are viewed and activated in the Programs panel. This limits the user’s access to certain applications when the Enabler is controlling the mobile device display. VX5 Reference Guide Wavelink Avalanche Enabler Configuration Figure 3-17 Application Shortcuts...
Page 125: Adapters
Wavelink Avalanche Enabler Configuration Adapters Note: LXE recommends the user review the network settings configuration utilities and the default values in Chapter 4 before setting All Adapters to Enable in the Adapters applet. Manage Network Setting Manage Wireless Settings Current Adapter...
Page 126: Figure 3-19 Avalanche Network Profile Displayed
A reboot may be required after enabling or disabling these options. Network For descriptions of these Enabler parameters, refer to Chapter 4 “Wireless Network Configuration”. VX5 Reference Guide Wavelink Avalanche Enabler Configuration Selecting the Avalanche Icon will access the Avalanche Network Profile tab which will display current network settings.
Page 127: Status
Link speed indicates the speed at which the signal is being sent from the adapter to the mobile device. Speed is dependent on signal strength. E-EQ-VX5RG-G Figure 3-21 Status Display VX5 Reference Guide...
Page 128 Wavelink Avalanche Enabler Configuration VX5 Reference Guide E-EQ-VX5RG-G...
Page 129: Chapter 4 Wireless Network Configuration
The VX5 radios rely on Microsoft Windows network configuration via the Windows Control Panel and configuration software that depends on the type of radio installed in the VX5. The VX5 has all necessary radio software and drivers installed before it is shipped. The radio software includes a configuration utility and a status monitor or diagnosis utility.
Page 130: Use Windows To Configure Wireless Settings
“Use Windows to configure my wireless network settings” must remain unchecked for the SCU (Summit), ACU (Cisco) or Mobile Companion (Symbol) to control the wireless network configuration. VX5 Reference Guide Use Windows to Configure Wireless Settings Figure 4-1 Windows Wireless Network Properties...
Page 131: Summit Radio
Summit Radio Summit Radio Please refer to the “LXE Security Primer” to prepare the Authentication Server and Access Point for VX5 communication. It is important that all dates are correct on mobile computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail.
Page 132: Help
The WZC utility has an icon in the toolbar that looks like networked computers with a red X through them, indicating that Wireless Zero Config application is enabled but the connection is inactive at this time (the VX5 is not connected to a network). •...
Page 133: Main Tab
Login password. The Active Profile may be changed without logging in. Once logged in, the button label changes to Admin Logout. The admin is also automatically logged out when the SCU is exited. E-EQ-VX5RG-G Figure 4-3 SCU – Main Tab VX5 Reference Guide...
Page 134: Admin Login
Access additional troubleshooting features on the Diags tab. After Admin login, the use can also: • Create, edit, rename and delete profiles on the Profile tab • Edit global parameters on the Global Setting tabs. VX5 Reference Guide Figure 4-4 Admin Password Entry Summit Radio E-EQ-VX5RG-G...
Page 135: Profile Tab
• Commit – Ensures that the profile settings made on this screen are saved in the profile. When not logged in, the parameters can be viewed, but cannot be changed. E-EQ-VX5RG-G Figure 4-5 SCU – Profile Tab VX5 Reference Guide...
Page 136: Parameters
50, 30, 10 or 1 mW Default: Maximum Bit Rate Options: Auto = Rate negotiated automatically with the AP 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 or 54 Mbit Default: Auto VX5 Reference Guide Summit Radio E-EQ-VX5RG-G...
Page 137 Extensible Authentication Protocol (EAP) type used for 802.1x authentication to AP Options: None LEAP EAP-FAST PEAP-MSCHAP PEAP-GTC Default: None Note: The EAP type chosen determines if the Credentials button is active. Available entries on the Credentials pop up window vary by EAP type chosen. E-EQ-VX5RG-G VX5 Reference Guide...
Page 138 – The settings for Auth Type, EAP Type and Encryption depend on the security IMPORTANT type chosen. determine the proper settings for the security type implemented on the wireless LAN. VX5 Reference Guide Please refer to “Summit Wireless Security”, later in this chapter, to Summit Radio E-EQ-VX5RG-G...
Page 139: Status Tab
After completing radio configuration, it is a good idea to review this screen to verify the radio has associated (no encryption, WEP) or authenticated (LEAP, any WPA), as indicated above. E-EQ-VX5RG-G Figure 4-6 SCU – Status Tab VX5 Reference Guide...
Page 140: Diags Tab
Diagnostic Output box. If a fixed IP address has been assigned to the radio, this is also noted in the Diagnostic Output box. Note that the current IP address is displayed above this button. VX5 Reference Guide Figure 4-7 SCU – Diags Tab Summit Radio...
Page 141: Global Settings Tab
The radio must be disabled and then re-enabled in the Windows Control Panel. Note: Custom parameter options – LXE does not support the parameter Custom option. The parameter value is displayed as “Custom” when the operating system registry has been edited to set the Summit parameter to a value that is not available from the parameter’s...
Page 142 APs on the same channel . Options: On, Off Default: CCX Features Use of Cisco Compatible Extensions (CCX) radio management and AP specified maximum transmit power features. Options: On, Off Default: VX5 Reference Guide Summit Radio E-EQ-VX5RG-G...
Page 143 Aux only = Aux antenna only On = Use diversity Default: For a VX5 with a single external antenna use Main Only. For a VX5 with dual external antennas use On. RX Diversity How to handle antennas diversity when receiving packets from AP.
Page 144 Default: Certs Path A valid directory path, of up to 64 characters, where Root CA certificates for EAP authentication (PEAP/MSCHAP, PEAP/GTC) are stored. LXE suggests ensuring the directory path currently exists before assigning the path in this parameter. Default: \Files\Summit\certs...
Page 145 Options: 0 to 30,000 ms Default: 5000 Ping Delay ms The amount of time, specified in milliseconds, between each ping. Options: 0 to 30,000 ms Default: 1000 E-EQ-VX5RG-G VX5 Reference Guide...
Page 146: Sign-On Vs. Stored Credentials
Notes: More details are provided in the appropriate Summit Wireless Security section following in this chapter. If invalid credentials are entered into the stored credentials, the authentication will fail. No error message is displayed and the user is not prompted to enter valid credentials. VX5 Reference Guide Summit Radio E-EQ-VX5RG-G...
Page 147: Figure 4-9 Sign-On Screen
Reconnect button on the Diags tag is clicked or the profile is modified and the Commit button is clicked. E-EQ-VX5RG-G Figure 4-9 Sign-On Screen VX5 Reference Guide...
Page 148: Summit Wireless Security
• On the Main tab, click the Admin Login button and enter the password. • LXE recommends editing the default profile with the parameters for your network. Select the Default profile from the pull down menu. • Make any desired parameter changes as described in the applicable following section determined by network security type and click the Commit button to save the changes.
Page 149: No Security
Once configured, click the Commit button. Ensure the correct Active Profile is selected on the Main tab. The SCU Main tab shows the device is associated after the radio connects to the network. E-EQ-VX5RG-G Figure 4-11 No Security VX5 Reference Guide...
Page 150: Wep
• Enter the SSID of the Access Point assigned to this profile • Set EAP Type to None • Set Encryption to Manual WEP • Set Auth Type to Open VX5 Reference Guide Figure 4-12 WEP Encryption Summit Radio E-EQ-VX5RG-G...
Page 151: Figure 4-13 Wep Keys
Once configured, click the Commit button. Ensure the correct Active Profile is selected on the Main tab. The SCU Main tab shows the device is associated after the radio connects to the network. E-EQ-VX5RG-G Figure 4-13 WEP Keys VX5 Reference Guide...
Page 152: Leap Without Wpa Authentication
Please see “WPA/LEAP” later in this section to configure the radio for WPA LEAP. Please review “Sign-On vs. Stored Credentials”, earlier in this chapter. VX5 Reference Guide If the Cisco/CCX certified AP is configured for open authentication, set the Auth Type radio parameter to Open.
Page 153: Figure 4-15 Leap Credentials
Once configured, click the Commit button. Ensure the correct Active Profile is selected on the Main tab. The SCU Main tab shows the device is associated after the radio connects to the network. E-EQ-VX5RG-G Figure 4-15 LEAP Credentials VX5 Reference Guide...
Page 154: Peap/Mschap
User Name and Password when connecting to the network. • For Stored Credentials, User, Password and the CA Certificate Filename must be entered. Enter these items as directed below. VX5 Reference Guide Figure 4-16 PEAP/MSCHAP Summit Radio E-EQ-VX5RG-G...
Page 155: Figure 4-17 Peap/Mschap Credentials
For information on generating a Root CA certificate, please see “Root CA Certificate” later in this chapter. Note: The date must be properly set on the device to authenticate a certificate. E-EQ-VX5RG-G Figure 4-17 PEAP/MSCHAP Credentials Figure 4-18 PEAP/MSCHAP Certificate Filename VX5 Reference Guide...
Page 156: Peap/Gtc
User Name and Password when connecting to the network. • For Stored Credentials, User, Password and the CA Certificate Filename must be entered. Enter these items as directed below. VX5 Reference Guide Figure 4-19 PEAP/GTC Summit Radio E-EQ-VX5RG-G...
Page 157: Figure 4-20 Peap/Gtc Credentials
For information on generating a Root CA certificate, please see “Root CA Certificate” later in this chapter. Note: The date must be properly set on the device to authenticate a certificate. E-EQ-VX5RG-G Figure 4-20 PEAP/GTC Credentials Figure 4-21 PEAP/GTC Certificate Filename VX5 Reference Guide...
Page 158: Wpa/Leap
• Set Auth Type to Open Please see “LEAP” earlier in this section to configure the radio for LEAP without WPA. Please review “Sign-On vs. Stored Credentials”, earlier in this chapter. VX5 Reference Guide Figure 4-22 WPA/LEAP Summit Radio E-EQ-VX5RG-G...
Page 159: Figure 4-23 Wpa/Leap Credentials
Click OK then click Commit. Ensure the correct Active Profile is selected on the Main tab. The SCU Main tab shows the device is associated after the radio connects to the network. E-EQ-VX5RG-G Figure 4-23 WPA/LEAP Credentials VX5 Reference Guide...
Page 160: Eap-Fast
RADIUS server. The RADIUS server must have auto provisioning enabled to send the PAC provisioning credentials to the client device. Please refer to the “LXE Security Primer” for more information on the RADIUS server configuration.
Page 161: Figure 5-25 Eap-Fast Credentials
When using Automatic PAC Provisioning, once authenticated, there is a file stored in the \System directory with the PAC credentials. If the username is changed, that file must be deleted. The filename is autoP.00.pac. E-EQ-VX5RG-G Figure 5-25 EAP-FAST Credentials VX5 Reference Guide...
Page 162: Wpa Psk
• Enter the SSID of the Access Point assigned to this profile • Set EAP Type to None • Set Encryption to WPA PSK • Set Auth Type to Open VX5 Reference Guide Figure 4-26 WPA/PSK Encryption Summit Radio E-EQ-VX5RG-G...
Page 163: Figure 4-27 Psk Entry
Once configured, click the Commit button. Ensure the correct Active Profile is selected on the Main tab. The SCU Main tab shows the device is associated after the radio connects to the network. E-EQ-VX5RG-G Figure 4-27 PSK Entry VX5 Reference Guide...
Page 164: Eap-Tls For Summit
To start configuring the wireless connection, click on the icon in the system tray. The Wireless Network Connection screen appears. Click the Change advanced settings link. VX5 Reference Guide Figure 4-28 Wireless Network System Tray Icon Figure 4-29 Wireless Network Connections...
Page 165: Figure 4-30 Connection Properties, General Tab
Make sure the Use Windows to configure my wireless network settings box is checked. WPA/LEAP is the exception and this box should not be checked when using WPA/LEAP. To add a new wireless network click the Add button. E-EQ-VX5RG-G Figure 4-30 Connection Properties, General Tab VX5 Reference Guide...
Page 166: Figure 4-32 Wireless Network Properties, Association Tab
Enter the SSID in the Network Name (SSID) text box. Select WPA from the Network Authentication pull down list. Select TKIP from the Data Encryption pull down list. To configure authentication, click the Authentication tab at the top of the screen. VX5 Reference Guide Summit Radio E-EQ-VX5RG-G...
Page 167: Eap-Tls Configuration
User Certificate If the VX5 was used to request the user certificate, it may have been installed by the CA. To check if a correct user certificate is installed: 1. Navigate to Start | Run and type mmc.
Page 168: Setting Eap/Tls Parameters
Setting EAP/TLS Parameters Set the Wireless Network Connection Properties per instructions in “Wireless Network Configuration” earlier in this chapter. Click the Authentication tab. VX5 Reference Guide Figure 4-34 Wireless Network Association Summit Radio E-EQ-VX5RG-G...
Page 169: Figure 4-35 Wireless Network Authentication
Click the Properties button. Click the Use a certificate on this computer button and check Use simple certificate selection box, as shown above. E-EQ-VX5RG-G Figure 4-35 Wireless Network Authentication Figure 4-36 Smart Card or Certificate Properties VX5 Reference Guide...
Page 170: Validating The Server Certificate
The radio re-starts with the new parameters and validates the server CA certificate. Finally navigate back to the properties configuration screen and check the Connect to these servers box. VX5 Reference Guide Figure 4-37 Validating Server Certificate Summit Radio E-EQ-VX5RG-G...
Page 171: Figure 4-38 Connect To Servers
The radio will re-start with the new parameters and validate the server certificate. A message box will appear asking if the server certificate is the correct certificate as shown below. E-EQ-VX5RG-G Figure 4-38 Connect to Servers Figure 4-39 Validate Servers Confirmation VX5 Reference Guide...
Page 172: Figure 4-40 Connect To Server
Click OK and the VX5 fills in the correct name of the server certificate in the text field left blank above. VX5 Reference Guide Figure 4-40 Connect to Server Summit Radio E-EQ-VX5RG-G...
Page 173: Cisco Radio
To access the configuration utility, select Programs | Cisco Aironet | Aironet Client Utility (ACU) from the Microsoft Windows Start menu. If profiles have already been created, a profile can be selected by clicking on the Select Profile icon. E-EQ-VX5RG-G Figure 4-41 Cisco Aironet Client Utility VX5 Reference Guide...
Page 174: Figure 4-42 Cisco Profile Selection Screen
To remove a profile from automatic selection, highlight the profile name and click Remove>>. Figure 4-43 Cisco Profile Selection Management Screen More details on the Profile Manager are available in Cisco’s online help. VX5 Reference Guide Figure 4-42 Cisco Profile Selection Screen Cisco Radio E-EQ-VX5RG-G...
Page 175: Figure 4-44 Cisco Profile Manager Screen
You can use the Import/Export buttons to backup profiles or transfer profiles between computers: • Import a profile from a selected drive/directory, such as a floppy. • Export a profile to a selected drive/directory, such as a floppy. E-EQ-VX5RG-G Figure 4-44 Cisco Profile Manager Screen VX5 Reference Guide...
Page 176: Profile Properties Screens
Network type – The default is Infrastructure. Infrastructure mode is used to connect to a wired network, such as an Ethernet, via access points. Ad hoc mode is used to connect two or more computers in a small temporary network. VX5 Reference Guide Figure 4-45 Cisco Properties – System Parameters Cisco Radio...
Page 177: Figure 4-46 Cisco Properties – Rf Network
Access Point and switch to that Access Point. The default is selected. The time period of association before scanning and the signal strength can be configured. LXE recommends 10 seconds for the association time before scanning and 40% for the signal strength.
Page 178: Figure 4-47 Cisco Properties – Advanced (Infrastructure)
The default is 2312. • RTS Retries – The number of times the radio re-sends the RTS packet if a CTS is not received. The default is 16. VX5 Reference Guide Cisco Radio E-EQ-VX5RG-G...
Page 179: Figure 4-48 Cisco Properties – Advanced (Ad Hoc)
• Beacon Period – Specifies the duration between beacons, which are used to help clients find each other in Ad Hoc mode. E-EQ-VX5RG-G Figure 4-48 Cisco Properties – Advanced (Ad Hoc) VX5 Reference Guide...
Page 180: Encryption
Select “None” and check “Static WEP” to use static WEP. Click the Static WEP Keys… button to configure the keys. • Select “LEAP” and click on Configure LEAP… to use LEAP. VX5 Reference Guide Figure 4-49 Cisco Properties – Network Security Cisco Radio E-EQ-VX5RG-G...
Page 181: Static Wep
ACII Text – the WEP key contains ASCII text, including alpha characters, numbers and punctuation marks. 40 bit keys consist of 10 hexadecimal or 5 ASCII text characters. 128 bit keys consist of 26 hexadecimal or 13 ASCII text characters. VX5 Reference Guide...
Page 182: Leap
No Network Connection Unless User is Logged In – Forces the client adapter to disassociate after you log off so another user cannot access the network without entering a user name and password. VX5 Reference Guide Figure 4-51 Cisco Properties – LEAP Settings Cisco Radio...
Page 183 • LEAP Authentication Timeout Value – The amount of time (in seconds) before a LEAP Authentication is considered failed. An error message is then displayed. The range is 10 to 300 seconds. The default is 90. E-EQ-VX5RG-G VX5 Reference Guide...
Page 184: Diagnostics
Link Test – Tests the performance of the radio with an Access Point (specified by IP Address). • Site Survey – Monitors the signal strength, beacons received, link speed and link quality. VX5 Reference Guide Figure 4-52 Cisco Link Status Meter Cisco Radio E-EQ-VX5RG-G...
Page 185: Updating Firmware
To automatically load new firmware when a new radio driver is installed, click on the Preferences icon on the main Cisco screen. Make sure the checkbox for “Automatically load new firmware when NDIS driver is updated” is checked. E-EQ-VX5RG-G Figure 4-53 Cisco Preferences VX5 Reference Guide...
Page 186: Wpa For The Cisco Radio
Although Microsoft patch #Q815485 also provides WPA functionality with previous versions of Windows XP, this version was not tested by LXE. All configuration examples shown in this section are from a VX5 with SP2 installed. Please refer to the “LXE Security Primer” to prepare the Authentication Server and Access Point for VX5 communication.
Page 187: Installing Radio Drivers
Cisco Radio Installing Radio drivers How much of the LXE released Cisco drivers/tools should be installed depends on what authentication protocol is to be configured. • Cisco PEAP should not be installed if using PEAP/MSCHAP. • Cisco PEAP must be installed if using PEAP/GTC.
Page 188: Installing/Uninstalling The Cisco Peap Supplicant
Installing/Uninstalling the Cisco PEAP Supplicant To install or uninstall Cisco PEAP navigate to Start | Control Panel | Add Remove Programs on the VX5 computer. Choose the Cisco Aironet Installation Wizard. Click the Change/Remove button. To install Cisco PEAP, click the Custom Installation/Upgrade button.
Page 189: Figure 4-57 Cisco Component Installation
• Expand the Security Modules and uncheck the PEAP box. Click the next button until the supplicant loads. Once the new supplicant installs or uninstalls you will be prompted to reboot the VX5. E-EQ-VX5RG-G Figure 4-57 Cisco Component Installation Figure 4-58 Reboot Prompt...
Page 190: Wireless Network Configuration Utility
To start configuring the wireless connection, click on the icon in the system tray. The Wireless Network Connection screen appears. Click the Change advanced settings link. VX5 Reference Guide Figure 4-59 Wireless Network System Tray Icon Figure 4-60 Wireless Network Connections...
Page 191: Figure 4-61 Connection Properties, General Tab
Make sure the Use Windows to configure my wireless network settings box is checked. WPA/LEAP is the exception and this box should not be checked when using WPA/LEAP. To add a new wireless network click the Add button. E-EQ-VX5RG-G Figure 4-61 Connection Properties, General Tab VX5 Reference Guide...
Page 192: Figure 4-63 Wireless Network Properties, Association Tab
To continue with the authentication process, please refer to the appropriate section, later in this chapter, for the desired authentication protocol: • “PEAP/MS-CHAP Configuration” • “PEAP/GTC Configuration” • “WPA/LEAP Configuration” • “EAP-TLS Configuration” • “WPA/PSK Configuration” VX5 Reference Guide Cisco Radio E-EQ-VX5RG-G...
Page 193: Peap/Ms-Chap Configuration
Figure 4-64 Wireless Network Properties, Authentication Tab Set the EAP type to Protected EAP (PEAP). “Installing/Uninstalling the Cisco PEAP Supplicant” to uninstall the Cisco PEAP supplicant. Click the Properties button. E-EQ-VX5RG-G If the text is not exactly as shown, see VX5 Reference Guide...
Page 194: Figure 4-65 Peap Properties
Configure this box depending on what username and password are used to login to Windows XP and the user credentials for the MSCHAP authentication. Left unchecked, the VX5 will prompt for a User Name and Password. Click the OK buttons back to the Wireless Network Properties screen.
Page 195: Server Authentication
Check the Validate server certificate and the root CA in the list box Trusted Root Certificate Authorities. Do not check the Connect to these servers box. This will authenticate the root CA only and not the RADIUS server. E-EQ-VX5RG-G Figure 4-67 Login Screen Figure 4-68 PEAP Properties VX5 Reference Guide...
Page 196: Figure 4-69 Connection Message Box
When the radio connects with the new configuration parameters, a connection message is displayed. Click the message box to process your logon. The server sends its certificate and the VX5 displays a message asking if this certificate is the correct one. If this is the correct certificate click the OK button.
Page 197: Figure 4-71 Peap Properties And Server Name
Now the ACS certificate is being validated and configuration is complete. When the radio connects with the new parameters, the Network Connected message box is displayed. E-EQ-VX5RG-G Figure 4-71 PEAP Properties and Server Name Figure 4-72 Network Connected Box VX5 Reference Guide...
Page 198: Peap/Gtc Configuration
Open the Cisco ACU and click the Set profile button. Click the Use Another Application to Configure My Wireless Settings button. Click OK. Configure the Wireless settings per “Wireless Network Configuration”, earlier in this chapter. VX5 Reference Guide Figure 4-73 Cisco ACU Profile Selection Screen Cisco Radio E-EQ-VX5RG-G...
Page 199: Figure 4-74 Authentication Properties
Uncheck Always try to resume secure session box. If checked, this will not authenticate a user when they sign in if the previous authentication is still valid in the ACS server. Click the Properties button. E-EQ-VX5RG-G Figure 4-74 Authentication Properties Figure 4-75 PEAP Properties VX5 Reference Guide...
Page 200: Figure 4-76 Generic Token Card Properties
When the radio re-connects a One Time Password sign-on screen will appear. Enter the RSA user name and the one time password (OTP) from the hardware token and click VX5 Reference Guide Figure 4-76 Generic Token Card Properties Figure 4-77 One Time Password...
Page 201: Validate Server Certificate
Check the Connect only if server is signed by specified root CA box. Click OK to dismiss the configuration screens. The root CA will be validated only when the radio re-connects with the new wireless parameters in this configuration. E-EQ-VX5RG-G Figure 4-79 PEAP Properties Certificate Authority VX5 Reference Guide...
Page 202: Figure 4-80 Acs Server Verification
When the radio connects with these parameters, the server sends the server certificate and a message displays asking if this is correct. If it is correct click Yes and the text field will be filled in automatically. VX5 Reference Guide Figure 4-80 ACS Server Verification Cisco Radio...
Page 203: Wpa/Leap Configuration
Cisco Radio WPA/LEAP Configuration LEAP is a Cisco proprietary authentication protocol and is not supported by the Microsoft supplicant. To configure the VX5 for WPA/LEAP use the Cisco ACU installed during normal installation of the Cisco radio driver. Cisco ACU Start the Cisco ACU by clicking the icon on the desktop or navigate to Start | Programs | Cisco | ACU.
Page 204: Figure 4-83 System Parameters
Enter a Client Name. You should use a unique name for each VX5. Type the SSID in the text field SSID1. Click the Network Security tab at the top of the screen. Check the Wi-Fi Protected Access (WPA) box. TKIP and Open will automatically be checked and the other options grayed out when WPA is checked.
Page 205: Figure 4-85 Leap Settings
Click the Select Profile icon from the main ACU screen. Click the Use Selected Profile button. Use the drop down box to choose the profile just configured. Click OK. The VX5 will associate and then display the sign on screen. E-EQ-VX5RG-G Figure 4-85 LEAP Settings Figure 4-86 Select Profile...
Page 206: Figure 4-87 Leap User Name And Password
Cisco Radio Figure 4-87 LEAP User Name and Password A sign on status box will display. Figure 4-88 Sign On Status VX5 Reference Guide E-EQ-VX5RG-G...
Page 207: Figure 4-89 Cisco Status
Cisco Radio Once connected, click the Status icon at the main ACU screen to show the configuration of the VX5. E-EQ-VX5RG-G Figure 4-89 Cisco Status VX5 Reference Guide...
Page 208: Eap-Tls Configuration
User Certificate If the VX5 was used to request the user certificate, it may have been installed by the CA. To check if a correct user certificate is installed: 1. Navigate to Start | Run and type mmc.
Page 209: Setting Eap/Tls Parameters
Cisco Radio Setting EAP/TLS Parameters Set the Wireless Network Connection Properties per instructions in “Wireless Network Configuration” earlier in this chapter. Click the Authentication tab. E-EQ-VX5RG-G Figure 4-91 Wireless Network Association VX5 Reference Guide...
Page 210: Figure 4-92 Wireless Network Authentication
Click the Properties button. Click the Use a certificate on this computer button and check Use simple certificate selection box, as shown above. VX5 Reference Guide Figure 4-92 Wireless Network Authentication Figure 4-93 Smart Card or Certificate Properties Cisco Radio...
Page 211: Figure 4-94 Validating Server Certificate
Click OK to dismiss the configuration screens. The radio re-starts with the new parameters and validates the server CA certificate. Finally navigate back to the properties configuration screen and check the Connect to these servers box. E-EQ-VX5RG-G Figure 4-94 Validating Server Certificate VX5 Reference Guide...
Page 212: Figure 4-95 Connect To Servers
The radio will re-start with the new parameters and validate the server certificate. A message box will appear asking if the server certificate is the correct certificate as shown below. VX5 Reference Guide Figure 4-95 Connect to Servers Figure 4-96 Validate Servers Confirmation...
Page 213: Figure 4-97 Connect To Server
Cisco Radio Click OK and the VX5 fills in the correct name of the server certificate in the text field left blank above. E-EQ-VX5RG-G Figure 4-97 Connect to Server VX5 Reference Guide...
Page 214: Wpa Psk Configuration
Enter an ASCII network key in the Network key text field. Enter the same key in the Confirm network key text field. There is no server authentication when using WPA-PSK, so no additional configuration is needed. VX5 Reference Guide Figure 4-98 Wireless Properties Association Cisco Radio...
Page 215: Symbol Radio
The Up and Down buttons move the highlighted profile up or down in the list. The order of the profiles (as displayed in the list) corresponds to the order in which the profiles are searched if association with the current profile is lost. E-EQ-VX5RG-G Figure 4-99 Symbol WLAN Profiles Select VX5 Reference Guide...
Page 216: Figure 4-100 Symbol Profile – Mode
Select worldwide if the radio is used with a non-Symbol (or pre AP- 4131 model Symbol access point). VX5 Reference Guide Figure 4-100 Symbol Profile – Mode Symbol Radio...
Page 217: Figure 4-101 Symbol Profile – Ip Configuration
The rightmost position provides the best network performance, but consumes the most power. E-EQ-VX5RG-G Figure 4-101 Symbol Profile – IP Configuration Figure 4-102 Symbol Profile – Power VX5 Reference Guide...
Page 218: Encryption (Wep)
(there are two five-digit boxes per key) and click the OK button to enable 40-bit encryption. Use the Reset Keys button to clear any entered keys. VX5 Reference Guide Figure 4-103 Symbol Profile – 40 bit Encryption Symbol Radio...
Page 219: Figure 4-104 Symbol Profile – 128 Bit Encryption
If the access point is using a passkey, then the active profile must use one too. The passkey is a plain text representation of the WEP keys, providing an easy way to enter WEP data without remembering the entire WEP key. E-EQ-VX5RG-G Figure 4-104 Symbol Profile – 128 bit Encryption VX5 Reference Guide...
Page 220: Diagnostics
Fewer retries indicate a better signal and this condition is represented by a green indicator. If the indicator is red, associating with a different access point may reduce the number of retries and improve the signal. VX5 Reference Guide Figure 4-105 Symbol Status – Signal Symbol Radio...
Page 221: Figure 4-106 Symbol Status – Information
This screen is read only and cannot be changed by the user. To change IP settings, use the configuration screen covered earlier in this chapter. E-EQ-VX5RG-G Figure 4-106 Symbol Status – Information Figure 4-107 Symbol Status – IP Status VX5 Reference Guide...
Page 222: Figure 4-108 Symbol Status – Ping Test
Selecting “Set Roaming” allows the radio to associate with any access point with a better signal. Note: These setting are temporary. They are not saved to the registry. VX5 Reference Guide Figure 4-108 Symbol Status – Ping Test Figure 4-109 Symbol Status – AP’s Symbol Radio Click the Start Test button.
Page 223: Figure 4-110 Symbol – Available Wlans
The signal strength of the WLAN is indicated from one bar (weakest) to five bars (strongest). Encrypted networks are indicated with a “key” icon. Updating Firmware Symbol radio firmware is automatically updated when the radio driver is updated. E-EQ-VX5RG-G Figure 4-110 Symbol – Available WLANs VX5 Reference Guide...
Page 224: Certificates
Certificates Root CA Certificate Please refer to the “LXE Security Primer” for more information on obtaining and installing certificates. The easiest way to get the root CA certificate is to use a browser to navigate to the CA. To request the root CA certificate, open a browser to http://<CA IP address>/certsrv.
Page 225: Figure 4-113 Download Ca Certificate Screen
Certificates Click the save button and save the certificate. Make sure to keep track of the name and location of the certificate. E-EQ-VX5RG-G Figure 4-113 Download CA Certificate Screen Figure 4-114 File Download Confirmation VX5 Reference Guide...
Page 226: Figure 4-115 Certificate Install
A message may appear when the certificate is about to install confirming that you want to install the certificate. Once the certificate is installed, return to the proper authentication section, earlier in this chapter. VX5 Reference Guide Figure 4-115 Certificate Install Certificates...
Page 227: User Certificate
Certificates are date sensitive and if the date is not correct authentication may fail. If the VX5 was used to request the user certificate, it may have been installed by the CA. To check if a correct user certificate is installed: 1.
Page 228: Troubleshooting
Make sure the “Use Windows to configure my wireless network setting” checkbox IS NOT checked when using WEP. If using WPA and the Microsoft supplicant, this box MUST be checked. VX5 Reference Guide Figure 4-117 Windows Wireless Network Properties Troubleshooting...
Page 229: Chapter 5 Troubleshooting
Hardware Problems - (i.e. power source, keyboard, display, hard drive, PCMCIA cards, optional devices, etc.) • Radio Problems • Software Related problems • Memory The following sections provide more detailed troubleshooting information about each of these areas. E-EQ-VX5RG-G VX5 Reference Guide...
Page 230: Startup Problems
This section lists some of the configuration error messages that may appear at system startup and their possible solutions. Note: If you press the power switch and the VX5 remains off, refer to the “Power Source” section of this chapter. Problem...
Page 231: Bypassing Microsoft Windows Startup
Windows with a minimum number of drivers. The Windows Start Up Menu Allows several choices that aid in diagnosing a problem. To access the start-up menu: Turn on the VX5. Press and hold the <F5> key. When the Windows Start Up Menu appears, select the desired choice: Normal Logged (\BOOTLOG.TXT)
Page 232: Verifying Boot Order
Verifying Boot Order During bootup, the <F2> key may be pressed to enter BIOS Setup. Turn on the VX5. Press <F2> immediately. The BIOS Setup Main Menu is displayed. Move the highlight to the Boot Menu. Select “Boot Device Priority” by pressing the <Down Arrow> to highlight it.
Page 233: Hardware Problems
This section lists possible solutions to some common problems with hardware. Power Source The VX5 receives power from either an AC-DC adapter or a vehicle battery. Power source problems are usually interrelated. For example, a malfunctioning AC-DC adapter or vehicle battery will not power the computer.
Page 234: Keyboard
Appendix A “Key Maps” for correct key combinations. Press the <SP> key or an arrow key to release the <2 state. If the problem continues, contact LXE Customer Support department. Note: The 95-key keyboard does not have 2 functionality.
Page 235: Pcmcia Cards
If the folder doesn’t display all the files stored in the folder, recovering data is unlikely. Refer to your software documentation for file recovery procedures. Many software packages automatically create backup files or restore points. VX5 Reference Guide...
Page 236: Irq Assignments
IRQ Assignments The VX5 has 16 IRQs, numbered 0 through 15, many of which are already assigned as follows: IRQs IRQ0 IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 IRQ8 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 Note: Please note that the IRQ assignments may change if additional hardware is added.
Page 237: Optional Devices
Optional Devices This section provides information on solving problems related to optional devices. Note: Make sure the VX5 is powered on before you turn on any powered optional devices. To help determine which device is causing the problem: • Check that all connecting cables are correctly and firmly attached. Loose cables can cause erroneous or intermittent signals.
Page 238: Radio And Network Problems
• Configuration of radio card/network All VX5 radios include utilities to aid in diagnosing transmission problems. Please refer to Chapter 4, “Wireless Network Configuration” for details on using the diagnostic features. Chapter 4 also includes a “Troubleshooting” section. Please review the information there if experiencing troubles with the 2.4 GHz network.
Page 239: Software Related Problems
Be sure you have enough memory and hard disk space to meet the software requirements. Determining Software Revision The Gnumber of the LXE loaded Windows image on the VX5 can be read in the system registry Use the Microsoft Registry Editor (REGEDIT.EXE) and browse to the following key: HKEY_LOCAL_MACHINE\SOFTWARE\LXE\VX5...
Page 240: System Testing
• • • • POST Error Messages The following table lists the POST error messages for the VX5. If problems persist, contact LXE’s Customer Support. 0200 Failure Fixed Disk Possible Cause The fixed disk is not properly identified in BIOS.
Page 241 Action Contact LXE’s Customer Support for CMOS battery replacement. 0251 System CMOS checksum bad – Default Configuration Used Action CMOS has been corrupted. The VX5 is loading with default settings. Run Setup to modify values. 0260 System timer error Action Contact LXE’s Customer Support.
Page 242 02B2/02B3 Incorrect Drive A/B type – Run Setup Action Run the BIOS Setup utility. 02D0 System cache error – Cache disabled Action Contact LXE’s Customer Support. 02F0 CPU ID: Possible Cause Contact LXE’s Customer Support. 02F4 EISA CMOS not writeable Possible Cause Cannot write BIOS to CMOS.
Page 243: Post Informational Messages
Server BIOS2 test error: Fail-safe timer takes too long. Action Contact LXE’s Customer Support. POST Informational Messages The following table lists the POST informational messages for the VX5. Message nnn kB System RAM Passed nnn kB Extended RAM Passed nnn kB Cache/Shadow RAM Passed...
Page 244: If You Need Further Assistance
Before You Call Since some problems you experience may be related to the operating system or software, it is important to investigate other sources of assistance first. Try the following before contacting LXE. • Review the troubleshooting information in commercially available Microsoft Windows documentation.
Page 245: Appendixa Key Maps
Caps Lock Shift Ctrl The key map table that follows lists the commands used for the VX5. Note that since the VX5 uses a Microsoft Windows operating system, no DOS Terminal Emulation keypress sequences are provided. Key Map 101-Key Equivalencies There are ten hidden keys on the 95-key keyboard.
Page 246: 60-Key Standard Keypad
The Brightness Adjustment keys have no function. Brightness is adjusted via the buttons on the VX5 control panel. The Contrast Adjustment keys have no function because the VX5 is equipped with a TFT display that has no provision for these adjustments.
Page 247 The Keyboard Backlight key is used in <2 “VMT Keyboard Backlighting” in Chapter 4, “System Configuration”. The Suspend/Resume key has no function as Windows Power Management controls all power management modes on the VX5. Press <Ctrl> then <2 E-EQ-VX5RG-G Press These Keys and Then...
Page 248 To get this key VX5 Reference Guide Press These Keys and Then Shift Ctrl CapsLock 60-key Standard Keypad Press this key E-EQ-VX5RG-G...
Page 249 7 (alpha) 8 (alpha) 9 (alpha) 0 (alpha) DOT (alpha) 1 (numeric) 2 (numeric) 3 (numeric) 4 (numeric) 5 (numeric) 6 (numeric) 7 (numeric) 8 (numeric) E-EQ-VX5RG-G Press These Keys and Then Shift Ctrl CapsLock Press this key VX5 Reference Guide...
Page 250 + (numeric) + (alpha) * (numeric) * (alpha) : (colon) ; (semicolon) _ (underscore) , (comma) ‘ (apostrophe) ~ (tilde) “ & VX5 Reference Guide Press These Keys and Then Shift Ctrl CapsLock 60-key Standard Keypad Press this key E-EQ-VX5RG-G...
Page 251: Ibm 3270 Keypad Ovelay
The 60-key keypad is available with an IBM 3270 overlay designed to allow the user to enter terminal emulator commands when running LXE’s RFTerm program. When running this program please refer to the following reference guide for equivalent keys and keypress sequences: •...
Page 252 60-key Standard Keypad VX5 Reference Guide E-EQ-VX5RG-G...
Page 253: Appendixb Technical Specifications
External Connectors/ Interfaces Power Connector Power Switch Beeper Dimensions Available storage options may vary based on date of manufacture and other VX5 options. E-EQ-VX5RG-G Specification 933MHz PIII 1 MB BIOS Flash 256 or 512MB SDRAM SVGA compatible controller 40 or 80 GB...
Page 254: Environmental Specifications
Features Battery for CMOS External AC Adapter Power Supply Environmental Specifications The VX5 will withstand the following environmental characteristics and has been tested in accordance with applicable sections of MIL-STD-810E. Feature Altitude Operating Temperature Storage Temperature Water, Sand and Dust...
Page 255: Display Specifications
-30 °C to +50 °C (-22 °F to +122 °F) -40 °C to +70 °C (-40 °F to +158 °F) IP66 per IEC60529 10-90% Non-condensing at 40°C (104°F) Bounce loose cargo for 0.5 hour duration. Common carrier transportation, transit face. 15 kV VX5 Reference Guide...
Page 256: Radio Specifications
2.4 - 2.4835 GHz IEEE 802.11b DS SS 11 Mbps 100 mW 11 US, 13 Europe, 4 France, 1 Japan see VX5 Environmental Specs see VX5 Environmental Specs Novell, TCP/IP, Ethernet, ODI PCMCIA 2.0, Type II slot 2.4 - 2.5 GHz IEEE 802.11b DS SS...
Page 257: Revision History
Added IBM 3270 and IBM 5250 overlay information to “The 60-key QWERTY Keyboard” section. Chapter 4 – System Revised “The VX5 Drivers CD-ROM” and “Serial Port Pin 9”. Configuration Chapter 5 – RF Network Revised Figure 4-6, Cisco Properties - RF Network.
Page 258 Explanation Front Page Updated LXE logo and date. Chapter 1 – Introduction Added VX1/2/4 Power Adapter Cable to VX5/6/7 Series to Accessories list. Chapter 3 – Power Supply Added section for VX1/2/4 Power Adapter Cable. Chapter 5 – RF Network Revised “Troublehooting”...
Page 259 Chapter 3 – System Renamed and revised section “Screen Blanking Service” to “Screen Blanking Configuration Utility”. Revised “Microsoft Windows License Agreement (First Boot)” and “The VX5 Drivers CD-ROM” for Summit. Chapter 4 – RF Network Added section for Summit radio.
Page 260 Chapter 1 – Introduction Added footnote to “Overview” section. Chapter 3 – System Revised “Drive C Directory Structure”. Configuration Revised “Wavelink Avalanche Enabler Configuration” for Avalanche Mobility Center. Appendix B – Technical Revised “Physical Specifications”. Specifications VX5 Reference Guide Revision History E-EQ-VX5RG-G...
Page 261: Index
CMOS NiCd Battery ...58 CMOS time and date not set...214 Color Cable Wiring...56 COM ports Setup ...67 COM1/Scanner Connection, Location ...6 COM2 Connector, Location ...6 Comm Ports COM 1 ...19, 20 COM 1 - 03F8h...16 COM 2 ...19, 21 VX5 Reference Guide...
Page 262 Display Contrast Control Keys...43 Display Specification...239 Display, Specs ...237, 239 Diversity Receive...127 Transmit ...127 Document Conventions ...3 Dot Pitch, Specs...239 EAP-TLS ...151, 192, 211 VX5 Reference Guide Enabler Adapter options...109 communication...100 Configuration ...100 Connection ...103 Execution ...104 File Menu ...101 Global options...111 Passwords...101...
Page 263 Printer Port...19 RS232 ports...19 Scanner Port...19 Serial Ports ...19 USB Connector ...19 LPT ports setup ...67 LXE Customer Support ...228 Manuals ...10 Mass Storage, Specs ...237 Memory ...16, 237 Network Troubleshooting 2.4GHz Wireless ...222 Ethernet...222 Non-System disk or disk error...214 Normal Operating Mode...17...
Page 264 Power Management ...17 BIOS ...69 Power On Self Test (POST) ...224 POST Messages Error Messages...224 Informational Messages ...227 Power Source VX5 Reference Guide Troubleshooting ...217 Power Status LED ...18 Power Supply CMOS Battery ...17 CMOS NiCd Battery...58 Power Supply, Specs ...238 Power Switch...18...
Page 265 Parallel Port...67 Serial Port ...67 USB Port ...68 Slot 0 (Left) ...48 Slot 1 (Right) ...48 Software Troubleshooting ...223 Software Loaded by LXE...76 Speaker Jack, Location...4, 6 Speaker Volume Control Keys ...43 Speaker/Beeper, Location...4, 5 Specification Input Power...57 Specifications Audio Connector...30 Display ...239...
Page 266 Product Key ...1, 75 Software Key ...1, 75 Windows Management Instrumentation (WMI) ...60 Wire Color Cable Wiring...56 WMI Support...60 EAP-TLS ...151, 192, 211 LEAP ...187 VX5 Reference Guide PEAP/GTC...182 PEAP/MSCHAP ...177 PSK ...198 Supported Authentications...113 Summit Radio...115 System Requirements...170 WPA/LEAP Summit Radio ...142, 144...

LXE VX5 Reference Manual

Chapter 1 Introduction

Overview

When to Use this Guide

Quick Start

Components

Data Entry

Getting Help

Manuals and Accessories

Chapter 2 Physical Description and Layout

Hardware Configuration

Physical Controls

External Connectors

The Keyboards

The Display

Factory Default Settings

Pcmcia/Cardbus and ATA Slots

Power Supply

Chapter 3 System Configuration

Introduction

BIOS Setup

Serial Port Pin 9

VMT Keyboard Backlighting

Microsoft Windows Setup and Configuration

Touchscreen

Network Configuration

Screen Blanking Utility

VX5 Delivered with no Hard Drive

VX5 Delivered with no os

The VX5 Drivers CD-ROM

Wavelink Avalanche Enabler Configuration

Chapter 4 Wireless Network Configuration

Introduction

Use Windows to Configure Wireless Settings

Summit Radio

Cisco Radio

Symbol Radio

Certificates

Quick Links

Troubleshooting

Related Manuals for LXE VX5

Summary of Contents for LXE VX5