Page 2
Summit Data Communications, Inc. Summit Data Communications, the Summit logo, and “The Pinnacle of Performance” are trademarks of Summit Data Communications, Inc. All rights reserved. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by LXE, Inc. is under license.
Appendix B Regulatory Notices and Safety Information Note: A complete revision history is included in Appendix B, “Regulatory Notices and Safety Information”. Revision Notice VX3Plus User’s Guide Explanation Update approvals for 802.11 a/b/g radio. Remove Summit Declaration of Compliance for consistency.
VX3P EHICLE OUNT Introduction ... 1 Identifying the VX3Plus Computer ...2 Document Conventions ...3 Environmental Specifications...3 VX3Plus without Touchscreen... 4 Quick Start... 4 Troubleshooting...5 Components ... 6 Microsoft Windows CE Control Panel... 8 The Half-Screen Display ... 8 AppLock and the VX3Plus... 9 Single Application AppLock ...9...
Page 6
Procedure ...25 Step 1 – Mount Vehicle RAM Clamp Mount ...25 Mounting Dimensions... 26 Step 2 – Attach RAM Mount Ball to the VX3Plus ...27 Step 3 – Attach VX3Plus Assembly to RAM Mount...28 Completed Assembly...28 Strain Relief Cable Clamps ... 29 Install Stylus Tether and Sleeve (Optional) ...
Page 7
Distance from Label ...49 Successful Scan ...49 Unsuccessful Scan...49 Bluetooth Scanners ...50 Voice Data ...50 Bluetooth Devices... 51 PPENDIX The VX3Plus Keypad ... 53 Key Map 101-Key Equivalencies...53 IBM 3270 Keypad Overlay ...58 IBM 5250 Keypad Overlay ...58 PPENDIX EGULATORY Approvals ... 60 Revision History...
The keys on the keypad are constructed of a phosphorescent material that can easily be seen in dimly lighted areas. The VX3Plus provides the power and functionality of a desktop computer in a vehicle mounted unit, with a wide range of options: •...
Identifying the VX3Plus Computer VX3Plus The VX3Plus is identified by the “VX3Plus” logo located at the bottom right of the keypad. The VX3Plus is covered in this document and the VX3Plus Reference Guide. VX3X The VX3X is identified by the “VX3X” logo located above the keypad.
-22°F to 158°F (-30°C to 70°C) [non-condensing] 5% to 95% non-condensing at 104°F (40°C) Based on MIL Std 810D 8 kV air, 4kV contact 75G, 5ms duration, 100 shock impacts 32.8 feet (10 meters) Direct line of sight only. VX3Plus User’s Guide...
VX3Plus without Touchscreen If a VX3Plus is not equipped with a touchscreen of if your system administrator has disabled the touchscreen, please see the Keypad Shortcuts section, later in this manual, for helpful keypress sequences. Your system administrator may need to use LXEConnect to configure the VX3Plus. Complete details on using LXEConnect to configure theVX3Plus are in the VX3Plus Reference Guide.
AppLock is installed and running on the mobile device. AppLock restricts User access to running programs. Changes or modifications require Administrator access. Refer to AppLock in the VX3Plus Reference Guide for setup and processing information. Tap File | Exit to close the RFTerm application.
Components Left Port Strain Relief Clamps Right Port The following combinations are offered for the VX3Plus Endcap Left Port COM3 (RS-232) COM3 (RS-232) USB-Host (USB-H) USB-Host (USB-H) Endcap Display Programmable Key Beeper On/Off Button VX3Plus User’s Guide RS-232 Figure 1 VX3Plus Components, Top View...
Components Note: The RAM ball shown above is shipped unattached. The installer must assemble the RAM ball to the back of the VX3Plus. See “Installation” later in this manual for details. E-EQ-VX3PLUSOGWW-B Figure 3 VX3Plus Components, Back View RAM Ball...
Microsoft Windows CE user guides or the on-line Help application for these standard configuration options. The Half-Screen Display The VX3Plus has a half screen LCD color display capable of supporting VGA graphics mode. The resolution is 640 x 240 pixels. The display type is either: •...
AppLock. Multi Application AppLock A checkmark indicates applications currently active or available for Launching by the user. When Keyboard is selected, the VX3Plus default input method (Input Panel, Transcriber, or custom input method) is activated. Note: If “Keyboard”...
The previous application continues to run in the background. End-user key presses affect the application in focus only. See the VX3Plus Reference Guide for AppLock setup instruction. VX3Plus User’s Guide AppLock and the VX3Plus...
The QWERTY Keyboard The QWERTY Keyboard The VX3Plus has a QWERTY keyboard, available with a standard ANSI overlay, an IBM 3270 overlay or an IBM 5250 overlay. These keyboards have 101 keyboard functions, including a numeric keypad. Please refer to Appendix A, “Key Maps”, for keypress combinations.
Shft VX3Plus User’s Guide Function For information on programming these keys, please refer to the “VX3Plus Reference Guide”. By default, these keys function as Enter keys, except for IBM 5250 configurations where the left button is configured as “Field Exit”.
CAPS OR Shift – result is an uppercase letter. • CAPS AND Shift keypress – result is a lowercase letter. For information on preserving Caps configuration after a reboot, please see refer to the “VX3Plus Reference Guide”. Keypad Shortcuts Use keyboard shortcuts instead of the stylus: •...
Amber when on and unlit when off. Status Indicator. STAT • Amber when device is booting up. • Blinking Green when display Suspend state begins. VX3Plus User’s Guide SHFT CAPS Break Figure 8 LED Functions keypress. The QWERTY Keyboard STAT...
The QWERTY Keyboard General Windows CE Keyboard Shortcuts Use the keyboard shortcuts in the chart below to navigate with the VX3Plus keyboard. These are standard keyboard shortcuts for Windows CE applications. Press these keys … CTRL + C CTRL + X...
When the virtual keyboard is displayed, the physical keyboard is still active. Therefore it is possible to input data from both keyboards. Enabling the Input Panel The Input Panel is disabled by default. Please see the “VX3Plus Reference Guide” for details on enabling the Input Panel VX3Plus User’s Guide...
Power Supply Power Supply Vehicle power input for the VX3Plus is 12V to 80V DC and is accepted without the need to perform any manual adjustments within the VX3Plus. See the section titled “Installation”, sub- section titled “Vehicle 12-80V DC Direct Connection”.
LXE Manuals CD or logon information for the ServicePass web pages. You can also get help from LXE by calling the telephone numbers listed on the LXE Manuals CD, in the file titled “Contacting LXE”. This information is also available on the LXE website.
Page 27
Manuals and Accessories Power Supplies Power Supply, External, AC, W/US Power Cord VX3Plus Power Supply, External, AC, No Power Cord VX3Plus Adapter Cable for AC Power Supply to VX3Plus Antenna Mount Kits Remote Mount Antenna Assembly Kit, 8 Ft Cable...
Page 28
Bluetooth Scanner and Accessories LXE Bluetooth module with laser ring scanner, battery, two hand/wrist straps (large and small) LXE Bluetooth module with 1D/2D imager ring scanner, battery, two hand/wrist straps (large and small) Li-Ion Spare Battery for LXE Bluetooth Ring Scanner...
Equipment Needed: Phillips No. 1 screwdriver and a Torque wrench capable of measuring to 50 inch pounds (5.64±.56 N/m). Note: Torquing tool is not supplied by LXE. Tools needed to attach the RAM Clamp Mount to the vehicle are not supplied by LXE. The VX3Plus is designed to use a RAM mount system.
10-32 lock nuts VX3Plus User’s Guide RAM Mount System The RAM mounting assembly consists of the following parts: VX3Plus RAM ball (included with VX3Plus) RAM arm, size C RAM clamp mount RAM Clamp Mount includes: Upper Clamp Piece with Ball...
Align the bolts with the holes in the lower clamp piece. Place the nylon locking nuts (D) on the bolts and tighten the bolts. E-EQ-VX3PLUSOGWW-B Figure 10 RAM Clamp Mount Figure 11 Assembled RAM Clamp Mount Components VX3Plus User’s Guide...
Place the VX3Plus face down on a stable surface. Position the RAM ball bracket on the rear of the VX3Plus, aligning the studs on the back of the VX3Plus with the holes on the RAM ball mount bracket. Attach with three 10-32 lock nuts.
Slip the RAM arm over the ball on the vehicle RAM clamp mount. Insert the ball of the RAM mount bracket into the RAM arm. Adjust the VX3Plus to the desired position and tighten the knob on the RAM arm using the supplied RAM wrench.
Strain Relief Cable Clamps Equipment Required: Phillips screwdriver (not supplied by LXE) There are two strain relief cable clamps secured to the VX3Plus endcap. Use the strain relief clamps to secure audio, power, and I/O cables attached to the VX3Plus.
Stylus Clip so that the ends don’t interfere with placing the stylus in the Stylus Clip. Place the stylus in the Stylus Clip when not in use. An extra or replacement stylus can be ordered from LXE. See the section titled “Accessories” for the stylus part number.
Pin 9 of COM1 or COM3 (when present) may be configured to provide +5V or RI. To change Pin 9 of the port, please refer to the “VX3Plus Reference Guide”. Caution – Do Not Use the USB-C or USB-H Labeled Port for Tethered Scanners.
When you have finished using the scanner, remove it from the VX3Plus and store the scanner in a closed container or bag. Figure 19 VX3Plus with Generic Barcode Scanner Attached VX3Plus User’s Guide 1. Good Scan LED (or equivalent) 2. Trigger 3.
Caution – Do Not Use the USB-C or USB-H Labeled Port for PC serial cables or printers. The printer or PC cable requires a nine-pin D-shell female connector for the VX3Plus. The printer or PC cable is attached to the connector labeled “RS-232”.
The USB-C connector accepts an adapter cable which provides a USB client port. Cable requires a nine-pin D-shell female connector for the VX3Plus. Power off the VX3Plus before connecting the cable to the VX3Plus. Seat the connector firmly over the pins and turn the thumbscrews in a clockwise direction.
D-shell female connector for the VX3Plus. USB Host Type B Power off the VX3Plus before connecting the cable to the VX3Plus. Seat the connector firmly over the pins and turn the thumbscrews in a clockwise direction. Do not overtighten.
An adapter cable (LXE Part No. 9000A076CBLHEADSET1) can be attached to the audio port. The adapter cable has a 2.5mm plug on one end to attach to the VX3Plus and a quick disconnect connector on the other end to connect to a variety of LXE voice recognition headsets.
Connect the quick connect end of the adapter cable to the LXE headset. Align the pins and push the connectors together until they click and are locked in place. If the adapter cable is removed from the VX3Plus, replace the plug to ensure the VX3Plus is environmentally sealed.
Remote Mount Antenna Installation Sheet”, available on the LXE Manuals CD or ServicePass website, for details. If the VX3Plus has an internal antenna (no antenna connector on the endcap), the antenna was connected when the VX3Plus was manufactured. Connect Power Cable Connect the power cable to vehicle power (See the following section titled “Vehicle...
External Power Supply, Optional External Power Supply, Optional The LXE-approved AC Power Supply and Adapter Cable are only intended for use in a 25ºC (77ºF) maximum ambient temperature environment. In North America, this unit is intended for use with a UL Listed ITE power supply with output rated 12 –...
“Vehicle Connection Wiring Color Codes” for additional wire color-coding specifics. VX3Plus User’s Guide For proper and safe installation, the input power cable must be connected to a fused circuit on the vehicle. This fused circuit requires a 2 Amp maximum time delay (slow blow) high interrupting rating fuse.
Vehicle 12-80VDC Power Connection How To: Connect Vehicle 12-80VDC Connection The VX3Plus must be turned off and the power cable must be UNPLUGGED from the VX3Plus. While observing the fuse requirements specified above, connect the power cable as close as possible to the actual battery terminals of the vehicle. When available, always connect to unswitched terminals in vehicle fuse panel, after providing proper fusing.
Page 50
Vehicle 12-80VDC Power Connection VX3Plus User’s Guide E-EQ-VX3PLUSOGWW-B...
“VX3Plus Reference Guide” for configuration details. The VX3Plus can be placed in Suspend Mode. To enter suspend mode, tap the power button and release or select Start | Suspend. To exit suspend tap the screen, press any key or tap the power button.
Always use the point of the stylus for tapping or making strokes on the display. Never use an actual pen, pencil or sharp object to write on the touch screen. An extra or replacement stylus may be ordered from LXE. See the “Accessories” section for the stylus part number.
<Enter> or click the Calibration button. Touchscreen Protective Film LXE offers a replaceable touchscreen protective film to protect the touchscreen when the VX3Plus is used in an abrasive environment. Installation and removal instructions can be found earlier in this guide. E-EQ-VX3PLUSOGWW-B ®...
Microsoft Windows CE Event Sounds The VX3Plus includes a customized sound scheme. The customized WAV files are preferable to the standard Microsoft Windows CE sounds when using the internal speaker. VX3Plus User’s Guide...
Do not pour, spray, or spill any liquid on the scanner. The Barcode Scanner contains the circuitry, scanning motor and laser. Handle with appropriate care. Enter Data You can enter data into the VX3Plus through several different methods: • The tethered scanner connected to the COM1 serial port provides barcode data entry •...
The keyboard is used to manually input data that is not collected otherwise. Almost any function that a full sized computer keyboard can provide is duplicated on the VX3Plus keyboard but it may take a few more keystrokes to accomplish a keyed task.
Tethered Scanner Entry The following section is directed toward a generic tethered scanner connected to the COM1 serial port on the VX3Plus. Aiming the Barcode Scanner Aim the scanner away from you, direct it at the barcode and press the trigger to scan.
Only LXE Bluetooth scanners and LXE Bluetooth printers are supported by LXE. See Accessories. Voice Data Data is entered into the VX3Plus by speaking into the headset’s microphone when prompted. Please contact your System Administrator if assistance is needed with the voice software. VX3Plus User’s Guide...
When an active paired device, not the VX3Plus, enters Suspend Mode, is turned Off or leaves the VX3Plus Bluetooth scan range, the Bluetooth connection between the linked device and the VX3Plus is lost. There may be audible or visual signals as paired devices disconnect from the VX3Plus.
Page 60
Bluetooth Devices VX3Plus User’s Guide E-EQ-VX3PLUSOGWW-B...
CAPS Ctrl Shft The key map table that follows lists the commands used for the VX3Plus. Note that since the VX3Plus uses a Microsoft Windows CE operating system, no DOS Terminal Emulation keypress sequences are provided. Key Map 101-Key Equivalencies Note: This key mapping is used on VX3Plus computers that are NOT running LXE’s RFTerm.
Page 62
Page Down ScrollLock Left Scan key default value is Scan, however this key has no affect on an external scanner attached to the VX3X. Right Scan key default value is Enter. VX3Plus User’s Guide Press These Keys and Then Shift Ctrl...
Page 63
The VX3Plus Keypad To get this key E-EQ-VX3PLUSOGWW-B Press These Keys and Then Shift Ctrl CapsLock Press this key VX3Plus User’s Guide...
Page 64
To get this key < > VX3Plus User’s Guide Press These Keys and Then Shift Ctrl CapsLock The VX3Plus Keypad Press this key E-EQ-VX3PLUSOGWW-B...
Page 65
The VX3Plus Keypad To get this key : (colon) ; (semicolon) _ (underscore) , (comma) ‘ (apostrophe) ~ (tilde) “ & E-EQ-VX3PLUSOGWW-B Press These Keys and Then Shift Ctrl CapsLock Press this key VX3Plus User’s Guide...
The 60-key keypad is available with an IBM 3270 overlay designed to allow the user to enter terminal emulator commands when running LXE’s RFTerm™ program. When running this program please refer to the following reference guide for equivalent keys and keypress sequences: •...
A label on the exterior of the device should resemble one of the labels shown below (the label contains the LXE part number of the installed radio card). The labels shown below and affixed to the device, identify where the device may be used and where its use is restricted. Use of a device is prohibited in countries not listed below or otherwise identified by the label.
Pila de litio adentro. Peligro de explosión si la pila se reemplaza incorrectamente. Reemplace solamente con el mismo tipo o equivalente recomendado por el fabricante. (ES) Oppassen: Bevat Lithium-batterij. Incorrrecte plaatsing van batterij kan leiden tot explosiegevaar. Alleen vervangen door hetzelfde of door fabrikant aanbevolen gelijkwaardig type. (NL) E-EQ-VX3PLUSOGWW-B VX3Plus User’s Guide...
Page 70
Lithium Battery Safety Statement (GR) (JP) Dikkat: (TR) Legend: Chinese Danish Dutch English Finnish French German Greek VX3Plus User’s Guide (KR) (CN) Italian Japanese Korean Norwegian Portuguese Spanish Swedish Turkish Regulatory Notices E-EQ-VX3PLUSOGWW-B...
Page 71
Regulatory Notices A/C Power Supply Safety Statement – VX3Plus Output Rated 12 – 80 VDC, Minimum 15W. The LXE-approved AC Power Adapter is only intended for use in a 25ºC (77ºF) maximum ambient temperature environment. Optional A/C Power Supply: Outside North America, this unit is intended for use with an IEC certified ITE power supply with output rated as stated at the top of this page.
Regulatory Notices Revision History Revision A, Initial Release: May 2008 Revision B: September 2008 Section Appendix B Regulatory Notices and Safety Information E-EQ-VX3PLUSOGWW-B Explanation Update approvals for 802.11 a/b/g radio. Remove Summit Declaration of Compliance for consistency. VX3Plus User’s Guide...
Page 77
12V to 80V DC ...17 External Power Supply ...39 View Display ...44 Voice data...50 Volume adjust audio volume ...46 E-EQ-VX3PLUSOGWW-B VX3Plus Reference Guide ...2 Warning Laser light ...47 Windows CE Control Panel ...8 Help Screens ...8 Windows CE online Help...8 Wiring Color Codes...41...
Page 78
Index VX3Plus User’s Guide E-EQ-VX3PLUSOGWW-B...