HP 70427A User Manual page 612

Symbols
+10 Volt Precision Reference, 13-64
Numerics
0 ppm/V default, 10-20
0.05 ppm/V, 10-21
1.0 ppm/V, 10-22
1.5 GHz Diplexed Low-Pass Filter, 13-55
1.5 kHz, 10-10
10 kHz, 10-13
10 kHz/default, 10-12
10 MHz IN, 11-24
10 MHz Oscillator Adjustment, 15-8
10 MHz OVEN OUT, 11-25
10 MHz Timebase (A5Y1), 13-5
10 MHz to 100 MHz Frequency Multiplier, 13-7
100 MHz no tune, 10-16
100 MHz Oscillator, 13-14
100 MHz OUT+8 dBm, 11-27
100 MHz OUT-2 dBm, 11-26
100 MHz PLL BW, 10-17
100 MHz Reference Loop (A7A1), 13-6
100 MHz to 600 MHz Frequency Multiplier, 13-17
120-300, 480-600, 10-2
126 Hz default, 10-6
17 kHz, 10-14
2.3 MHz LPF, 13-20
2.4 GHz to 25.8 GHz Microwave Stepped Reference, 13-38,
13-50
20 dB Amplifier, 13-20
20 ppm/V, 10-23
25 Hz, 10-4
3.6 kHz, 10-11
30 kHz, 10-15
300 Hz, 10-7
300-600 Only, 10-3
4 kHz, 10-9
50 OHM terminations installation, 1-8
53 Hz, 10-5
600 MHz Bandpass Filter, 13-33
600 MHz no tune, 10-18
600 MHz OUT 0 dBm, 11-28
600 MHz OUT+20 dBm, 11-29
600 MHz PLL BW, 10-19
600 MHz Power Amplifier, 13-32
600 MHz Reference Loop (A7A2), 13-17
600 MHz STW Oscillator, 13-29
650 Hz, 10-8
80 dB Isolator, 13-16, 13-30
Index
A
A band 26.5 - 40, 10-24
A5Y1, 13-5
A7A1, 13-6
A7A2, 13-17
Access the Downconverter Screen, 2-5
Access the Source Screen, 2-27
Access the Tunable Source Screen, 2-40
ACT indicator, 11-3
Adjustments, 15-1
Advanced Hardware Control, 8-1
ALC ON| OFF, 10-25
AM DET MAX LVL, 10-27
AM Det Max Lvl, 10-26
AM Det Voltage, 10-28
AM Detector Filter, 13-60
AM Detector Noise Floor (AM NOISE), 14-51
AM Noise, 10-29
AM Noise and Spurs (mW LO), 14-24
AM Noise and Spurs (RF), 14-68
AM Noise Measurement (IF AM Detector) User Control, 3-17
AM Noise Measurement (Input AM Detector) System
AM Noise Measurement(IF AM Detector) System Control, 3-34
AM Noise Measurment (Input AM Detector) User Control, 3-13
AM NOISE output, 11-4
AM NSE IN | IF, 10-30
Amplitudes, 10-31
Atten, 10-32
AUTO ATTEN, 10-33
AUTO IF GAIN, 10-34
AUTO RANGE, 10-35
B
BEGIN, 10-36
BIAS ON| OFF, 10-37
BLOCK, 10-38
Block, 10-39
Block Diagram, 13-1
BUFFERED 10 MHz OUT, 11-30
C
Calibration Register, 7-10
Check Power Meter type and address, 15-1
Check RF Source type and address, 15-1
Command guidelines, 7-2
Command Punctuation, 7-2
Configure the Downconverter as a Microwave Source, 2-25
Control, 3-30
HP 70427A/HP 70428A User's Guide Index-i