Rear Panel - Sony BVP-E10 Series Product Information Manual

7-5-2

Rear Panel

ANALOG INPUT block
5PROMPTER connectors
4REFERENCE connectors
3RET1 through RET4 connectors
2MIC OUTPUT connectors
1CAMERA connector
CAMERA
REMOTE
MIC
INTERCOM
wfMIC REMOTE connector
wdINTERCOM REMOTE connector
wsRTS connectors
waINTERCOM/TALLY/PGM connector
w;COAX connector
qlSpare connectors
a a CAMERA connector (triax connector) a a
Connect a BVP-E10-series Color Video Camera using
a triax cable. All of the signals of the BVP-E10-series,
such as the power, control, video, and audio, can be
connected using a single triax cable. Various triax
connector types are supported; please contact your
local Sony office for details
Do NOT use a defective triax cable. The inner sheath of a triax
cable is used for power supply and the outer sheath for safety
ground. For your safety, do NOT use a triax cable whose inner
and outer sheaths are short-circuited. Use of such a cable may
cause electric shock.
b b MIC OUTPUT (microphone output) connectors b b
(XLR 3-pin)
Supply the microphone signals from the video camera.
c RET1 through RET4 (return video 1 through 4 c
c c
input) connectors (BNC type)
Accept the analogue return video signals from four
different sources. To select the appropriate return
signals use the RET1/RET buttons and RET2/3/4 switch
on the CA-570/P.
Note
When an optional BKP-7312 SDI input board is
installed, nothing should be connected to the RET 1
and RET 2 connectors in the ANALOGUE INPUT block.
d REFERENCE (reference signal input) d
d d
connectors (BNC type)
Accept a reference signal such as a black burst signal
for external synchronization.
e e PROMPTER (prompter signal input) connectors e e
(BNC type)
Accept the signals for a teleprompter.
f R, G, and B (R, G, and B signal output) f
f f
connectors (BNC type)
Supply the analogue R, G, and B signals for the video
switcher, chroma keyer, or other destination from each
connector.
MIC OUTPUT INPUT OUTPUT
CH-1 CH-2
RET 1 REFERENCE R Y WF1 VBS1 WF MODE
PROMPTER
RET 2 G R-Y PIX1 VBS2
REMOTE
RTS
RCP/CNU
RET 3 R B-Y WF2 VBS3
CHARACTER PIX2 AUX
RET 4 SYNC
INTERCOM/TALLY/PGM
COAX DIGITAL VIDEO
RET 1 RET 2 1 2 3
SERIAL INPUT SERIAL OUTPUT
DIGITAL VIDEO block
g g g Y, Cr, and Cb (component video signal output) g
connectors (BNC type)
Supply the analogue Y, Cr, and Cb signals from each
connector. Connect a VTR or a video switcher
conforming to analogue component video signals.
h CHARACTER (character signal output) h
h h
connector (BNC type)
Supplies the self-diagnostic results of this unit as a
video signal.
i WF1 and WF2 (waveform monitor 1 and 2 i i i
output) connectors (BNC type)
Supply the video signals for a waveform monitor. The
MONITOR SELECT function on an RCP-750/751unit
select the signal output from the WF 1 connector, and
the WAVEFORM MONITOR buttons on the MSU-700A/
750 select the signal output from the WF 2 connector.
j j PIX1 and PIX2 (picture monitor 1 and 2 output)
j j
connectors (BNC type)
Supply the video signals for a picture monitor. The
MONITOR SELECT function on an RCP-750/751 unit
select the signal output from the PIX 1 connector, and
the PICTURE MONITOR buttons on the MSU-700A/750
select the signal output from the PIX 2 connector.
k VBS1, VBS2, and VBS3 (composite video signal k
k k
1, 2, and 3 output) connectors (BNC type)
Supply composite video signals (VBS) from the video
camera.
l SYNC (sync signal output) connector (BNC type)
Supplies the sync signals (0.3 Vp-p, 75 ohms)
generated by the built-in sync signal generator.
Connect to the sync signal input connector of a
waveform monitor or picture monitor.
m m m m AC IN (AC power input) connector
Connect to an AC power source using the supplied AC
power cord. The power cord can be fixed to the CCU-
700A/700AP using the supplied plug holder.
Chapter 7 Location and Function of Parts and Controls
ANALOG OUTPUT block
6R, G, and B connectors
7Y, Cr, and Cb connectors
8CHARACTER connector
9WF1 and WF2 connectors
q;PIX1 and PIX2 connectors
qaVBS1, VBS2, and VBS3 connectors
qsSYNC connector
CCU-700P
110-120V 220-240V
Ú
AC IN
wgVoltage selector
110-120V
qdAC IN connector
qfWF MODE connector
qgRCP/CNU REMOTE connector
qhAUX REMOTE connector
qjSERIAL OUTPUT 1, 2, and 3 connectors
qkSERIAL INPUT RET 1 and RET 2 connectors
BVP-E10 Series Product Information Manual
71