Rear Control Panel - Sony BVP-E10 Series Product Information Manual

7
Chapter 7 Location and Function of Parts and Controls
116
BVP-E10 Series Product Information Manual

7-19-3Rear control panel

CA-905K/905F or CA-905L (during use with the CA-
950/950P only) with PinP switch sticker attached
POWER
FILTER LOCAL
wh FILTER LOCAL button
wg ND filter control
CENTER
MARKER
ON
OFF
wf CC filter control
wd CENTRE MARKER switch
ws SAFETY ZONE switch
wa MIX VF switch
w; UP TALLY switch
ql Spare switch
R
POWER
FILTER LOCAL
1
ND
A
CC
CENTER SAFETY VF
MARKER ZONE SCAN
ON ON 16:9
OFF OFF 4:3
a POWER indicator a a a
Illuminates as follows to show the power-supply status.
Green: Power is supplied to the camera.
Orange: Power is supplied to the camera, however
the VF PW button of the MSU-700 or RCP-700
Series unit is set to off and power is not supplied to
the viewfinder.
Not lit: Power is not supplied to the camera.
b Video signal select buttons b
b b
Select the video signals (R, G, and B) displayed on the
viewfinder.
When no button is pressed, the following signals are
output:
When a monochrome viewfinder is used: The Y signal
is output to the viewfinder.
When a colour veiwfinder is used: The R, G, and B
signals are output to the viewfinder, and a colour
picture appears on the viewfinder.
c c H-POSI (horizontal position) control c c
Adjusts the horizontal position of the box cursor on the
viewfinder screen.
d V-POSI (vertical position) control d
d d
Adjusts the vertical position of the box cursor on the
viewfinder screen.
1 POWER indicator
2 Video signal select buttons
3 H-POSI control
4 V-POSI control
5 WIDTH control
6 HEIGHT control
7 CURSOR STORE button
R G B RET RET 1
3 H-POSI V-POSI
2 4
1 5
ND
C WIDTH HEIGHT STORE CORSOR
B
D
A E
1 2 3
CC
SAFETY VF UP SCREEN
VF DETAIL
ZONE SCAN TALLY SIZE DISPLAY MENU SELECT
ON 16:9 ON MARKER ON ON
ON
OFF
OFF 4:3 OFF OFF MENU CANCEL ENTER OFF
qh MENU SELECT knob
qj MENU SELECT switch
qk DISPLAY switch
G B RET RET 1
3 H-POSI V-POSI
2 4
5
C WIDTH HEIGHT STORE CORSOR
B D
E
1 2 3
UP SCREEN
TALLY SIZE DISPLAY MENU SELECT VF DETAIL
ON MARKER ON ON
ON
OFF
OFF OFF MENU CANCEL ENTER OFF
wjSCREEN SIZE MARKER switch
e e WIDTH control e e
Adjusts the width of the box cursor on the viewfinder
screen.
f HEIGHT control f
f f
Adjusts the height of the box cursor on the viewfinder
screen.
g g CURSOR STORE button g g
Press to store the size and position of the box cursor
by adjusting H-POSI, V-POSI, WIDTH, and HEIGHT
control.
Note
If the CURSOR ON button is not lit, the data cannot be
stored.
h RET (return video) button h h h
Push this button in to display in the viewfinder the
return video signal (2, 3, or 4) selected on the CA-950/
950P/ 570/ 570P. Push again to display the video
signal from the camera.
i i RET 1 (return video 1) button i i
Push this button to display the return video 1 signal on
the viewfinder screen. Push again to view the video
signal from the camera.
8 RET button
9 RET 1 button
q; Back tally lamp
qa CURSOR ON button
ON
qs CURSOR 1, 2, and 3 buttons
qd PinP switch (when the BKP-9057 is installed)
qf VF DETAIL control
qg VF DETAIL switch
ON
wkAssignable switch