Sony BVP-E10 Series Product Information Manual page 97

B MASTER and SLAVE buttons
Designate the master camera or the slave
cameras to adjust the white balance of multiple
cameras in Master/Slave mode. Press and light
up the MASTER button to specify the connected
camera to become the master. Press and light
up the SLAVE button to specify the connected
camera(s) to become slave. The slave cameras
follow the master camera settings. If you press a
button when lit, it cancels the selection.
b b STANDARD button b b
When you press this button, the video camera is
initialized to its standard state and the button
illuminates for several seconds. If you press the button
while it illuminates, the video camera reverts to the
original state before Standard was selected.
c Camera/CCU function ON/OFF buttons c c c
Various functions of the video camera or the CCU/
HDCU-series can be turned on and off from this panel.
CHAR
ACTER
5600K AUTO SKIN DTL
KNEE DETAIL GATE GAMMA
5600K: 5600K -electronic colour temperature
conversion function
AUTO KNEE: Auto knee function. When this button
is lit (ON), the knee point is automatically adjusted
according to the highlight content of the picture.
SKIN DETAIL: Skin tone detail function
DTL GATE: Skin tone detail gate function. When this
button is lit (ON), the adjustment range of the skin
tone detail is displayed in white on the PIX (picture)
monitor screen.
BLACK GAMMA: Black gamma function
CHARACTER: Self-diagnostic display function.
When this button is lit (ON), the contents of the self-
diagnosis of the CCU/HDCU-series are displayed
on the monitor connected to the CHARACTER
OUTPUT connector of the CCU/HDCU-series. The
contents are also mixed to the video signal to be
output from the PIX1 OUTPUT connector. Each time
you press this button, the status changes as
follows.
OFF _ ON (page 1) _ ON (page 2) . . .
_ ON (page n) _ OFF
The contents of the self-diagnosis may be
displayed when required even if this button is not lit.
The right two buttons are for future use and do not
function at present.
d WHITE (white balance manual adjustment) d d d
controls
Used to manually adjust the white balance. From the
left, the controls are for R, G, and B signal adjustment.
e BLACK/FLARE (black balance/flare balance e
e e
manual adjustment) controls and indicator
Used to manually adjust the black balance (when the
indicator is not lit) or the flare balance (when the
indicator is lit). From the left, the controls are for R, G,
and B signal adjustment. Selection between black
balance and flare balance is made using the
Maintenance menu.
f Camera number/tally indication window f
f f
The number of the camera being controlled from this
panel is displayed in orange. When a red tally signal is
sent to the camera, the number is displayed in black
and the background of the number illuminates in red.
When a green tally signal is sent to the camera, the
number is displayed in black and the background of
the number illuminates in green. When both the red
and green tally signals are simultaneously sent, the left
half of the background illuminates in red and the right
half illuminates in green.
g g g g ALARM indicator
Illuminates when the self-diagnostic function identifies
a problem in the camera or CCU system
h CALL button h h h
Press to send a call signal to the video camera. The
tally lamps on the camera and the red tally lamp on the
CCU/HDCU Series light, (or go off if already lit). When
the CALL button on the video camera is pressed, the
CALL button on this panel illuminates and a buzzer
sounds.
i PANEL ACTIVE button i i i
Press and light up the button to permit this panel to
control the camera system (Panel active status). The
IRIS/MB ACTIVE button also illuminates. If you press
BLACK
this button so that it goes dark, the panel will be
locked, preventing accidental misoperation.
j Power and output signal select block j j j
A CAM PW (camera power) button
B Signal output select buttons
C CLOSE button
k AUTO SETUP block k
k k
SKIN DTL
AUTO HUE
1 2
CAM PW TEST BARS
Press and light up this button to turn the power
supply to the video camera ON. (The button
promptly flashes until the camera becomes
ready for transmission.) When you press this
button again, it starts flashing and the power
supply is turned off.
Press and light up one of these buttons to
activate the test signal generator of the video
camera and send the respective signals.
TEST: To send a signal to test the video circuits
BARS: To send a colour bar signal
Note
The BARS button takes priority to the TEST
button. If the BARS button is lit, press the button
to turn it dark before pressing the TEST button.
Press and light the button to close the iris. To
release the close mode, press the button again
so that it goes dark.
1 2 3
AUTO SETUP
LEVEL START/
WHITE
BREAK
Chapter 7 Location and Function of Parts and Controls
BVP-E10 Series Product Information Manual
3
CLOSE
4
BLACK
97