Rear Panel - Sony BVP-E10 Series Product Information Manual

7
Chapter 7 Location and Function of Parts and Controls
68
BVP-E10 Series Product Information Manual
7-4-2

Rear Panel

1CAMERA connector 2MIC OUTPUT connectors
CAMERA
MIC OUTPUT
CH-1 CH-2
PROMPTER/RET 3
MIC REMOTE
6MIC REMOTE connector
a CAMERA connector (triax connector) a
a a
Connects to the CA-570/ 570P/ 905K/ 905F Camera
Adaptor attached to the BVP-E10 Series Color Video
Camera using a triax cable.
Note
Do NOT use a defective triax cable. The inner sheath
of a triax cable is used for power supply and the outer
sheath for safety ground. For your safety, do NOT use
a triax cable whose inner and outer sheaths are short-
circuited. Use of such a cable may cause electric
shock.
b MIC (microphone) OUTPUT connectors (XLR, 3- b
b b
pin)
Supply the microphone signals from the video camera.
c c INPUT connectors c c
REFERENCE INPUT connectors (BNC type)
Accept reference signals (black burst signal) for
external synchronization.
RET 1/RET 2 (return video signal 1/2) connectors
(BNC type)
Accept return video signals from two different sources.
PROMPTER/RET 3 (return video signal 3)
connectors (BNC type)
Accept a teleprompter signal or a return video signal.
Use the switch on the internal DM board to select
PROMPTER or RET 3.
d d OUTPUT connectors d d
Y/G, Cr/R, Cb/B (component video signal /RGB
output) connectors (BNC type)
Supply the analogue component signals or the R, G,
and B signals for a video switcher, VTR or chroma
keyer from each connector. Use the switch on the
internal VA board to select the signals to be output.
VBS1/2/3 (composite video signal 1/2/3 output)
connectors (BNC type)
Supply the signal from the video camera in composite
format. Use the switch on the internal VA board to
select the composite video signal or sync signal. When
4OUTPUT connectors
3INPUT connectors
INPUT OUTPUT
REFERENCE Y/G VBS3
RET 1 R-Y/R WF
RET 2 B-Y/B WF MODE
COAX
PIX
RCP/CNU
INTERCOM/TALLY/PGM REMOTE
8RCP/CNU REMOTE connector
7INTERCOM/TALLY/PGM connector
the sync signal (0.3 Vp-p, 75 ohms) is selected,
connect the VBS 3 connector to the sync signal input
connector on a waveform or picture monitor.
WF (waveform monitor output) connector (BNC type)
Supplies a video signal to a waveform monitor. The
WAVEFORM MONITOR button on the optional MSU-
700A/ 750 Master Setup Unit, MONITOR SELECT
function on the RCP-750/751 Remote Control Panel, or
MONITOR SELECT control on the BKP- 5973 CCU
Control Panel selects the signal output from the WF
connector.
WF MODE (waveform monitor mode) connector (4-pin)
Connects to the corresponding connector on a
waveform monitor to allow the sequential monitoring of
signals.
PIX (picture monitor output) connector (BNC type)
Supplies a video signal or video and character signals
together to a picture monitor.
Use the PICTURE MONITOR button on the MSU-700A/
750, MONITOR SELECT function on the RCP-750/751,
or MONITOR SELECT control on the BKP-5973 to
select the signal output from the PIX connector.
e e e SERIAL OUTPUT (serial digital video/audio e
output) connectors (BNC type)
Supply the video/microphone signals from the video
camera in serial digital format. CCU-550D/
550DPConnect to a digital video switcher or
component digital VTR.
f MIC REMOTE (microphone remote control) f f f
connector (D-sub, 15-pin)
Connects to an external control unit such as an audio
mixer. With the connected unit, you can set the
microphone input level of the video camera to -60, -50,
-40, -30, or -20 dB. You can also set the microphone
input level with a switch on the internal AT board.
5SERIAL OUTPUT connectors
VBS1
SERIAL
OUTPUT
VBS2
q;AC IN connecto
9COAX connector