Advertisement
Location and Function of Parts and Controls
1 Lens mount (C-mount)
Attach any C-mount lens or other optical equipment.
Note
The lens must not project more than 10 mm from the lens mount.
10 mm or less
2 Reference screw holes (at the top)
3 Reference screw holes/Tripod screw holes (at the bottom)
These precision screw holes are for locking the camera module.
Locking the camera module into these holes secures the optical
axis alignment.
You can install the camera on a tripod. To install on a tripod, you
will need to install a tripod adaptor VCT-ST70I to the camera on
the reference holes.
Rear Panel
1
6
1
5
4
3
3
32
XCL-U1000/U1000C
1 Lens mount (C-mount)
2 Reference screw holes
(at the top)
3 Reference screw holes/
Tripod screw holes
(at the bottom)
Lens mount shoulder
2
5
4
3
2
1
2
10
9
8
7
6
15
14
13
12
11
4
1 RS-232C connector (6-pin)
You can connect a senal cable to this connector to control a
camera module from a camera control device.
2 Monitor output connector (15-pin)
You can connect a monitor cable to this connector to display an
image on a multiscan monitor supporting UXGA resolution.
Note
If you connect a multiscan monitor that does not support UXGA
resolution, an image may not be displayed.
3 DC IN (DC power input) connector (12-pin)
You can connect a CCXC-12P05N camera cable to input the
+12 V DC power supply. The pin confi guration of this connector is
as follows.
4 DIGITAL IF (Interface) connector (26-pin)
You can connect a digital interface cable to this connector to
control a camera module from a host device utilizing the serial
communication protocol while outputting a video signal from the
camera module. You can input the external trigger signal via the
26-pin connector and operate a camera module in the external
trigger mode. The pin confi guration of this connector is as
follows.
Note
When operating a camera module by inputting an external
trigger signal via the 26-pin connector, be careful about trigger
pulse input specifi cations (DIGITAL IF terminal).
Connector Pin Assignments
1 RS-232C connector (6-pin)
Pin No.
Signal
1
TXD
2
RXD
3
Ground
2 Monitor output connector (15-pin)
Pin No.
Signal
1
R output
2
G output
3
B output
4
NC
5
Ground
6
Ground
7
Ground
8
Ground
3 DC IN (DC power input) connector (12-pin)
Pin No.
Signal
1
Ground
2
+12 V DC
3
Ground
4
NC
5
Ground
6
NC
4 DIGITAL IF (Interface) connector (26-pin)
Pin No.
Digital signal
1
INNER_SHIELD (Ground)
2
X0– (Output)
3
X1– (Output)
4
X2– (Output)
5
XCLK– (Output)
6
X3– (Output)
7
Ser TC+ (Input)
8
Ser TFG– (Output)
9
TRIG– (Input)
10
NC
11
NC
12
NC
13
INNER_SHIELD (Ground)
Pin No.
Signal
4
NC
5
NC
6
NC
Pin No.
Signal
9
NC
10
Ground
11
NC
12
NC
13
HD output
14
VD output
15
NC
Pin No.
Signal
7
NC
8
Ground
9
NC
10
Exposure pulse output
11
Trigger pulse input
12
Ground
Pin No.
Digital signal
14
INNER_SHIELD (Ground)
15
X0+ (Output)
16
X1+ (Output)
17
X2+ (Output)
18
XCLK+ (Output)
19
X3+ (Output)
20
Ser TC– (Input)
21
Ser TFG+ (Output)
22
TRIG+ (Input)
23
NC
24
NC
25
NC
26
INNER_SHIELD (Ground)
Advertisement
