Table of Contents
Advertisement
7
Chapter 7 Location and Function of Parts and Controls
72
BVP-E10 Series Product Information Manual
n WF MODE (waveform monitor mode) connector
n
n
n
(4-pin)
Connect to the corresponding connector of a
waveform monitor to monitor signals in sequential
mode. A sequential control signal is output from this
connector when you press the SEQ button on an RCP-
700 Series unit, which enables simultaneous
monitoring of the R, G, and B signals.
o RCP/CNU REMOTE (remote control panel/
o
o
o
camera command network unit remote control)
connector (8-pin)
Connect an MSU-700A, MSU-750, CNU-700, or RCP-
700 Series unit using a CCA-5 cable. Control signals
are then accepted. When an RCP-700 Series unit is
connected, the power is also supplied to the unit.
p AUX (auxiliary) REMOTE connector (8-pin)
p
p
p
Connect an external system. For details on
connections, refer to the authorized Sony
representative.
Note
If you connect an RCP-700 Series unit to the RCP/ CNU
REMOTE connector, this connector cannot supply
power to the connected equipment.
q
q SERIAL OUTPUT 1, 2, and 3 (serial digital video
q
q
signal 1, 2, and 3 output) connectors (BNC type)
Signals sent from the video camera are converted into
serial digital video signals and are supplied from these
connectors. These connectors function when an
optional BKP-7311 SDI output board is installed in the
CCU-700A/700AP. Connect these connectors to the
input connectors of a digital video switcher,
component digital VTR, etc.
r
r SERIAL INPUT RET 1 and RET 2 (serial digital
r
r
return video signal 1 and 2 input) connectors
(BNC type)
These connectors accept a 10-bit 4:2:2 component
serial digital video signals as return video signals.
They function when an optional BKP-7312 SDI input
board is installed in the CCU-700A/ 700AP, and
function as return video 1 and 2 input connectors.
When the BKP-7312 is installed, nothing should be
connected to the RET 1 and RET 2 connectors in the
ANALOGUE INPUT block.
s Spare connectors (BNC type)
s
s
s
t
t COAX (coaxial) connector (BNC type)
t
t
Accepts camera connection through a conventional
coax cable instead of triax by setting a switch on the
internal DM board. The unit cannot supply power to the
video camera through this connector.
When a return video function is used, the maximum
cable length of a 5C-2V (RG-6A/U) coaxial cable is 800
m (2,624 feet).
u
u INTERCOM/TALLY/PGM (programme audio)
u
u
connector (19-pin)
Supplies and accepts intercom, tally, and programme
audio signals. Connect to the corresponding
connector on the intercom system.
v RTS (RTS intercom) connectors (XLR 3-pin)
v
v
v
Connect an RTS intercom system.
w INTERCOM REMOTE connector (D-sub 25-pin)
w
w
w
Connect an external controller to control intercom
muting, producer-line interruption, and engineer line
interruption. This connector outputs the red tally, green
tally, tally and call signals, and camera number.
x MIC REMOTE (microphone remote control)
x
x
x
connector (D-sub 15-pin)
Connect an external control unit such as an audio
mixer. You can set the microphone input level of the
video camera to -60, -50, -40, -30, or -20 dB with the
connected unit. Set the microphone volume to the level
suitable for shooting conditions. You can also set the
microphone input level with the switch on the internal
board of this unit. This connector outputs the red tally,
and green tally signals.
y Voltage selector (only for the CCU-700AP)
y
y
y
The operating voltage of the CCU-700AP is set to 220
to 240 V AC at the factory. If the voltage of your local
power line is different, change the setting of the
voltage selector.
Advertisement
Table of Contents
