Msu-700A, Master Setup Unit; Operation Panel - Sony BVP-E10 Series Product Information Manual

connected to this connector. The selected input
connector number is supplied from this connector.

7-10.MSU-700A, Master Setup Unit

7-10-1Operation Panel

5 CLOSE button
4 Signal output select buttons
3 VF PW button
2 CAM PW button
1 ALL button
qa IC card insertion block
qs PICTURE MONITOR buttons
qd WAVEFORM MONITOR buttons
a ALL button a
a a
Press the button so it starts flashing to activate the 13
buttons located at the right (from CAM PW to AUTO
SETUP) for all the connected cameras of the same
group.
b CAM PW (camera power) button b
b b
Press and light up this button to turn the power supply
to the video camera ON. (The button promptly flashes
until the camera becomes ready for transmission.)
When you press this button again, it starts flashing and
the power supply to the camera is turned off.
c c VF PW (viewfinder power) button c c
BVP-900/P cameras only: Press and light up this
button to turn the power supply to the viewfinder ON.
When you press the button again, it goes dark and the
power supply is turned off.
d d Signal output select buttons d d
Press and light up one of these buttons to activate the
test signal generator of the video camera and send the
respective signals.
ALL CAM PW
PARA
MULTI
TALLY
PANEL
ACTIVE
EXPAND
qf Camera select block
qg Filter control block
o ~AC IN (AC power input) connector o
o o
Connect to an AC power source using the supplied AC
power cord. The power cord can be fixed to the VCS-
700 using the supplied plug holder.
6 STANDARD button
7 AUTO SETUP block
8 Camera/CCU function ON/OFF buttons
AUTO SETUP MODE
SKIN DTL LEVEL START/
VF PW TEST1 TEST2 BARS CLOSE STANDARD BREAK WHITE BLACK
AUTO HUE
KNEE DETAIL LVLDEP GAMMA CHROMA MATRIX
OFF OFF OFF OFF OFF OFF
KNEE KNEE MONO COLOR
APARTURE SAT COLOR CORRECT
5600K AUTO SKIN DETAIL SATURATION CONTRAST BLACK CHARACTER
KNEE DETAIL GATE GAMMA
1 2 3 4 5 CONFIGURATION
SCENE FILES STORE
MAINTENANCE
ECS
ON
ACCESS
ECS/SHUTTER GAMMA MASTER GAIN
R G B 1 2 3 4 5
ENC
PICTURE MONITOR FILTER CTRL ND
R G B A B C D E
SEQ ENC
IRIS/MB
WAVEFORM MONITOR CC
ACTIVE
1 2 3 4 5 6 7 8 9 10 11 12
qj IRIS/MB ACTIVE button
qh ECS/Shutter control block (left)
TEST 1: To send a sawtooth signal to test the video
circuits
TEST 2: To send a staircase signal
BARS: To send a colour bar signal
Note:
The BARS button takes priority to the other two
buttons. If the BARS button is lit, press the button to
turn it dark before pressing the TEST 1 or TEST 2
button.
e CLOSE (iris close) button e e e
Press and light the button to close the iris. Press again
to release the close mode.
f STANDARD button f
f f
When you press this button, the video camera is
initialized to its standard state and the button remains
illuminated for several seconds. If you press the button
during this time, the video camera returns to the state
before the button was lit.
For details, refer to the System Manual.
Chapter 7 Location and Function of Parts and Controls
BVP-E10 Series Product Information Manual
9 Scene file control block
q; Menu operation block
MULTI
CARD
FILE
PAINT
MASTER BLACK IRIS
EXT
AUTO
CALL
wa Iris control block
w; Camera number/
tally indication window
ql CALL button
qk MASTER BLACK control block
Gamma control block (center)
Master gain control block (right)
81