Table of Contents
Advertisement
CONTROLS
Pressing the Auxiliary IO Diagnostics icon will bring up the Auxiliary IO Diagnostics screen (Figure 10).
Pressing the Auxiliary IO Diagnostics icon
allows the operator to view voltages of the pressure sensors and actual pressures (left side of screen) to ensure
allows the operator to view voltages of the pressure sensors and actual pressures (left side of screen) to ensure
allows the operator to view voltages of the pressure sensors and actual pressures (left side of screen) to ensure
that the sensors are functioning properly. On the right side of the screen, operation commands are shown.
that the sensors are functioning properly. On the right side of the screen, operation commands are shown.
that the sensors are functioning properly. On the right side of the screen, operation commands are shown. When
a command is activated (Front door up, conveyor out, etc) the text in the corresponding boxes will change from
a command is activated (Front door up, conveyor out, etc) the
OFF to ON if the switch is working properly. The bottom left of the screen shows the temperature sensor status
OFF to ON if the switch is working properly. The bottom left of the screen shows the temperature sensor status
OFF to ON if the switch is working properly. The bottom left of the screen shows the temperature sensor status
and conveyor motor coil requirements (if the switch is on).
Pressing the Home icon will return the display to the Coil/Pots and I/Os diagnostics main screen (Figure 9).
From the Coil/Pots and I/Os diagnostics main screen (Figure 9), pressing the Hydro I/O Diagnostic icon
From the Coil/Pots and I/Os diagnostics main sc
the display to the Hydro IO Diagnostics screen (Figure 11).
the display to the Hydro IO Diagnostics screen (Figure 11).
This screen shows the coil commands for the hydrostatic pumps and the potentiometer settings. From this screen,
This screen shows the coil commands for the hydrostatic pumps and the potentiometer settings. From this screen,
This screen shows the coil commands for the hydrostatic pumps and the potentiometer settings. From this screen,
the operator can determine if the pumps are receiving the correct amount of current for the desired auger speed.
the operator can determine if the pum
The iMin and iMax settings that are shown are by default the minimum and maximum current that the system will
The iMin and iMax settings that are shown are by default the minimum and maximum current that the system will
The iMin and iMax settings that are shown are by default the minimum and maximum current that the system will
allow to the pump controls. This cannot be changed by the operator. The Ramp On and Ramp Off settings show
allow to the pump controls. This cannot be changed by the operator.
the speed at which the pumps will respond to a change in position of the potentiometer. These settings also
the speed at which the pumps will respond to a change in position of the potentiometer. These settings also
the speed at which the pumps will respond to a change in position of the potentiometer. These settings also
cannot be changed by the operator.
Coil CMD and Coil Current boxes show the operator what the system is requesting for current to the pumps and
Coil CMD and Coil Current boxes show the operator what the system is req
what the system is actually sending to the pumps. When the system is operating in a steady state, these numbers
what the system is actually sending to the pumps. When the system is operating in a steady state, these numbers
what the system is actually sending to the pumps. When the system is operating in a steady state, these numbers
should be equal.
Pressing the Home icon will return the display to the Coil/Pots and I/Os diagnostics main
OPERATION
REPLACEMENT PARTS
quirements (if the switch is on).
will return the display to the Coil/Pots and I/Os diagnostics main screen (Figure 9).
will return the display to the Coil/Pots and I/Os diagnostics main screen (Figure 9).
ps are receiving the correct amount of current for the desired auger speed.
will return the display to the Coil/Pots and I/Os diagnostics main screen (Figure 9).
Figure 9
cs screen (Figure 10). This screen
text in the corresponding boxes will change from
Figure 10
g the Hydro I/O Diagnostic icon will navigate
The Ramp On and Ramp Off settings show
uesting for current to the pumps and
READ complete manual CAREFULLY
Page # 26
screen (Figure 9).
Page | 7
BEFORE attempting operation.
Advertisement
Table of Contents
