Bandit INTIMIDATOR 15XP/1390 Operating & Parts Manual page 66

MODEL 15XP/1390
(THESE TORQUES ARE BASED ON DRY, CLEAN THREADS)
DESCRIPTION
Chipper Drum Bearing Bolts
Drum Head Shaft Bushing "4040"
Anvil
Knife Bolts
Rope/Line Shear Counter Knife Bolts
Rope/Line Shear Adjustment Bolts
Feedwheel Bearing Bolts
Feedwheel Bearing Set Screws
Grip-Tight Feedwheel Bearing Set Screws
"RE/TG" Hydraulic Feedwheel Motor Shaft Nut
Taperlock Keyless Feedwheel Coupler
Engine Hold Downs
Engine Hold Downs
Engine Sheave Bushing "SF"
Engine Sheave Bushing "E"
Chipper Sheave Bushing "E"
Chipper Sheave Bushing "F"
Autofeed Cartridge Nut
Autofeed Plus Solenoid Retainer Nut
Hitch Mount Bolts
Before tightening bolts be sure you have the correct size bolt for the correct amount of torque.
BASIC WHEEL TORQUE REQUIREMENTS (per mfg.)
KEEP LUG NUTS PROPERLY TIGHTENED, CHECK NEW UNIT BEFORE OPERATION, CHECK
AGAIN AFTER 20-25 MILES (32-40 km) AND REGULARLY CHECK AT LEAST WEEKLY.
5 & 6 Lug Hubs (1/2" - 20 Studs) ........................ 90 - 120 ft.-lbs. Torque (122 - 163 Nm)
8 Lug Hubs (1/2" - 20 Studs) .............................. 90 - 120 ft.-lbs. Torque (122 - 163 Nm)
8 Lug Hubs (9/16" - 18 Studs) ............................ 110 - 120 ft.-lbs. Torque (149 - 163 Nm)
8 Lug Hubs (5/8" - 18 Studs) .............................. 190 - 210 ft.-lbs. Torque (258 - 285 Nm) (Cone Nut)
8 Lug Hubs (5/8" - 18 Studs) .............................. 275 - 325 ft.-lbs. Torque (373 - 441 Nm) (Flange Nut)
8 Lug Hubs (22mm x 1.5 Studs) ......................... 450 - 500 ft.-lbs. Torque (610 - 678 Nm) (Flange Nut)
10 Lug Hubs (3/4" - 16 Studs) ............................ 450 - 500 ft.-lbs. Torque (610 - 678 Nm)
(Consult axle manufacturers manual shipped with each machine for specific axle‑stud‑wheel combination lug nut torques.)
Copyright 9/18
BOLT TORQUE CHART
9/16" - 12 NC
Use only factory approved knives and hardware.
BOLT SIZE TORQUE (FT.-LBS.)
5/8" - 11 NC
5/8" - 11 NC
1/2" - 13 NC
5/8" - 11 NC
1/4" - 20 NC
5/8" - 11 NC
1/2" - 13 NC
3/8" - 24 NF
1" - 20 NEF 250 - 300
M10 x 1.50
1/2" - 13 NC
5/8" - 11 NC
3/8" - 16 NC
1/2" - 13 NC
1/2" - 13 NC
5/8" - 11 NC
50
MAINTENANCE
TORQUE (Nm)
220 298
142 193
75 102
180 245
15
180 245
75 102
20
2
339 - 407
55
60
125 169
30
60
60
75 102
4 - 6 5 - 8
4 - 6 5 - 8
220 298
Bandit
20
27
3
74
81
41
81
81