YOKOGAWA WT332E User Manual page 125

7.4 Features
7.4.5 Harmonic Measurement (/G5 Option)
Item Specifications
Measured item All installed elements
Method PLL synchronization method
Frequency range Fundamental frequency of the PLL source is in the range of 10 Hz to 1.2 kHz.
PLL source • Select voltage or current of each input element.
• Input level
• The frequency filter must be turned on when the fundamental frequency is less than or equal to 200Hz.
FFT data length 1024
Window function Rectangular
Sample rate, window width, and upper limit of harmonic analysis
f in the equation is the input fundamental frequency.
* The upper limit of harmonic order can be decreased.
Accuracy
(The accuracy shown below is the sum of reading and range errors.)
When Line Filter is OFF
<WT310E/WT332E/WT333E>
Frequency
10 Hz ≤ f < 45 Hz
45 Hz ≤ f ≤ 440 Hz
440 Hz < f ≤ 1 kHz
1 kHz < f ≤ 2.5 kHz
2.5 kHz < f ≤ 5 kHz
<WT310EH>
Frequency
10 Hz ≤ f < 45 Hz
45 Hz ≤ f ≤ 440 Hz
440 Hz < f ≤ 1 kHz
1 kHz < f ≤ 2.5 kHz
2.5 kHz < f ≤ 5 kHz
• When the crest factor is set to 3.
• When λ (the power factor) is 1.
• Power figures that exceed 1.2 kHz are reference values.
• For a direct current range, add 10 μA to the current accuracy and (10 μv/direct current range) × 100% of range to the power
accuracy.
• For the external current sensor range, add 100 μA to the current accuracy and (100 μV/external current sensor range rating) ×
100% of range to the power accuracy.
• For nth harmonic component input, add ({n/(m + 1)}/50)% of (the nth harmonic reading) to the n + mth harmonic and n – mth
harmonic of the voltage and current, and add ({n/(m + 1)}/25)% of (the nth harmonic reading) to the n + mth harmonic and n –
mth harmonic of the power.
• Add (n/500)% of reading to the nth component of the voltage and current, and add (n/250)% of reading to the nth component
of the power.
• The accuracy when the crest factor is 6 or 6A is the same as the accuracy when the crest factor is 3 after doubling the
measurement range.
• The guaranteed accuracy ranges for frequency, voltage, and current, are the same as the guaranteed ranges for ordinary
measurement. If the amplitude of the high frequency component is large, influence of approximately 1% may appear in certain
harmonics. Because the influence depends on the size of the frequency component, if the frequency component is small with
respect to the range rating, the influence is also negligible.
7-12
50% or more of the rated measurement range when the crest factor is 3.
100% or more of the rated measurement range when the crest factor is 6 or 6A.
Fundamental Frequency
10 Hz to 75 Hz
75 Hz to 150 Hz
150 Hz to 300 Hz
300 Hz to 600 Hz
600 Hz to 1200 Hz
Voltage
0.15% of reading
+0.35% of range
0.15% of reading
+0.35% of range
0.20% of reading
+0.35% of range
0.80%+ of reading
+0.45% of range
3.05% of reading
+0.45% of range
Voltage
0.15% of reading
+0.35% of range
0.15% of reading
+0.35% of range
0.20% of reading
+0.35% of range
0.80%+ of reading
+0.45% of range
3.05% of reading
+0.45% of range
Sample Rate Window Width
f×1024 1
f×512 2
f×256 4
f×128 8
f×64 16
Current
0.15% of reading
+0.35% of range
0.15% of reading
+0.35% of range
0.20% of reading
+0.35% of range
0.80%+ of reading
+0.45% of range
3.05% of reading
+0.45% of range
Current
0.15% of reading
+0.35% of range
0.15% of reading
+0.35% of range
0.20% of reading
+0.35% of range
0.95%+ of reading
+0.45% of range
3.35% of reading
+0.45% of range
Upper Limit of Harmonic Analysis*
50
32
16
8
4
Power
0.35% of reading
+0.50% of range
0.25% of reading
+0.50% of range
0.40% of reading
+0.50% of range
1.56% of reading
+0.60% of range
5.77% of reading
+0.60% of range
Power
0.35% of reading
+0.50% of range
0.25% of reading
+0.50% of range
0.40% of reading
+0.50% of range
1.68% of reading
+0.60% of range
6.05% of reading
+0.60% of range
IM WT310E-02EN