Rf Frequency Bands; Bluetooth Low Energy - Receive (Rx) - Texas Instruments SimpleLink CC2652PSIP Manual

www.ti.com

8.9 RF Frequency Bands

Over operating free-air temperature range (unless otherwise noted).
Frequency bands

8.10 Bluetooth Low Energy - Receive (RX)

Measured on the CC2652xSIP-EM
DC/DC enabled and high power PA connected to V
All measurements are performed at the antenna input with a combined RX and TX path, except for high power PA which is
measured at a dedicated antenna connection. All measurements are performed conducted.
PARAMETER
125 kbps (LE Coded)
Receiver sensitivity
Receiver saturation
Frequency error tolerance
Data rate error tolerance
Data rate error tolerance
(1)
Co-channel rejection
(1)
Selectivity, ±1 MHz
(1)
Selectivity, ±2 MHz
(1)
Selectivity, ±3 MHz
(1)
Selectivity, ±4 MHz
(1)
Selectivity, ±6 MHz
Selectivity, ±7 MHz
(1)
Selectivity, Image frequency
Selectivity, Image frequency ±1
(1)
MHz
500 kbps (LE Coded)
Receiver sensitivity
Receiver saturation
Frequency error tolerance
Data rate error tolerance
Data rate error tolerance
(1)
Co-channel rejection
(1)
Selectivity, ±1 MHz
(1)
Selectivity, ±2 MHz
(1)
Selectivity, ±3 MHz
(1)
Selectivity, ±4 MHz
Copyright © 2022 Texas Instruments Incorporated
PARAMETER
reference design with T
unless otherwise noted.
DDS
TEST CONDITIONS
–3
Differential mode. BER = 10
–3
Differential mode. BER = 10
Difference between the incoming carrier frequency and
the internally generated carrier frequency
Difference between incoming data rate and the internally
generated data rate (37-byte packets)
Difference between incoming data rate and the internally
generated data rate (255-byte packets)
Wanted signal at –79 dBm, modulated interferer in
–3
channel, BER = 10
Wanted signal at –79 dBm, modulated interferer at ±1
–3
MHz, BER = 10
Wanted signal at –79 dBm, modulated interferer at ±2
–3
MHz, BER = 10
Wanted signal at –79 dBm, modulated interferer at ±3
–3
MHz, BER = 10
Wanted signal at –79 dBm, modulated interferer at ±4
–3
MHz, BER = 10
Wanted signal at –79 dBm, modulated interferer at ±6
–3
MHz, BER = 10
Wanted signal at –79 dBm, modulated interferer at ≥ ±7
–3
MHz, BER = 10
Wanted signal at –79 dBm, modulated interferer at image
–3
frequency, BER = 10
Note that Image frequency + 1 MHz is the Co- channel
–1 MHz. Wanted signal at –79 dBm, modulated interferer
at ±1 MHz from image frequency, BER = 10
–3
Differential mode. BER = 10
–3
Differential mode. BER = 10
Difference between the incoming carrier frequency and
the internally generated carrier frequency
Difference between incoming data rate and the internally
generated data rate (37-byte packets)
Difference between incoming data rate and the internally
generated data rate (255-byte packets)
Wanted signal at –72 dBm, modulated interferer in
–3
channel, BER = 10
Wanted signal at –72 dBm, modulated interferer at ±1
–3
MHz, BER = 10
Wanted signal at –72 dBm, modulated interferer at ±2
–3
MHz, BER = 10
Wanted signal at –72 dBm, modulated interferer at ±3
–3
MHz, BER = 10
Wanted signal at –72 dBm, modulated interferer at ±4
–3
MHz, BER = 10
Product Folder Links:
SWRS263A – FEBRUARY 2021 – REVISED JUNE 2022
= 25 °C, V = 3.0 V, f
c DDS RF
MIN
–3
CC2652PSIP
CC2652PSIP
MIN TYP MAX
2360 2500
= 2440 MHz with
TYP MAX
–103
>5
> (–300 / 300)
> (–320 / 240)
> (–100 / 100)
–1.5
(2)
8 / 4.5
(2)
44 / 37
(2)
46 / 44
(2)
44 / 46
(2)
48 / 44
(2)
51 / 45
37
(2)
4.5 / 44
–98
> 5
> (–300 / 300)
> (–350 / 350)
> (–150 / 175)
–3.5
(2)
8 / 4
(2)
43 / 35
(2)
46 / 46
(2)
45 / 47
Submit Document Feedback
UNIT
MHz
UNIT
dBm
dBm
kHz
ppm
ppm
dB
dB
dB
dB
dB
dB
dB
dB
dB
dBm
dBm
kHz
ppm
ppm
dB
dB
dB
dB
dB
13