Texas Instruments SimpleLink CC2652PSIP Manual page 14

CC2652PSIP
SWRS263A – FEBRUARY 2021 – REVISED JUNE 2022
Measured on the CC2652xSIP-EM
DC/DC enabled and high power PA connected to V
All measurements are performed at the antenna input with a combined RX and TX path, except for high power PA which is
measured at a dedicated antenna connection. All measurements are performed conducted.
PARAMETER
(1)
Selectivity, ±6 MHz
Selectivity, ±7 MHz
(1)
Selectivity, Image frequency
Selectivity, Image frequency ±1
(1)
MHz
1 Mbps (LE 1M)
Receiver sensitivity
Receiver saturation
Frequency error tolerance
Data rate error tolerance
(1)
Co-channel rejection
(1)
Selectivity, ±1 MHz
(1)
Selectivity, ±2 MHz
(1)
Selectivity, ±3 MHz
(1)
Selectivity, ±4 MHz
(1)
Selectivity, ±5 MHz or more
(1)
Selectivity, image frequency
Selectivity, image frequency
(1)
±1 MHz
(3)
Out-of-band blocking
Out-of-band blocking
Out-of-band blocking
Out-of-band blocking
Intermodulation
Spurious emissions,
(4)
30 to 1000 MHz
Spurious emissions,
(4)
1 to 12.75 GHz
RSSI dynamic range
RSSI accuracy
2 Mbps (LE 2M)
Receiver sensitivity
Receiver saturation
Frequency error tolerance
Data rate error tolerance
14 Submit Document Feedback
reference design with T
unless otherwise noted.
DDS
TEST CONDITIONS
Wanted signal at –72 dBm, modulated interferer at ≥ ±6
–3
MHz, BER = 10
Wanted signal at –72 dBm, modulated interferer at ≥ ±7
–3
MHz, BER = 10
Wanted signal at –72 dBm, modulated interferer at image
–3
frequency, BER = 10
Note that Image frequency + 1 MHz is the Co- channel
–1 MHz. Wanted signal at –72 dBm, modulated interferer
at ±1 MHz from image frequency, BER = 10
–3
Differential mode. BER = 10
–3
Differential mode. BER = 10
Difference between the incoming carrier frequency and
the internally generated carrier frequency
Difference between incoming data rate and the internally
generated data rate (37-byte packets)
Wanted signal at –67 dBm, modulated interferer in
–3
channel, BER = 10
Wanted signal at –67 dBm, modulated interferer at ±1
–3
MHz, BER = 10
Wanted signal at –67 dBm, modulated interferer at ±2
–3
MHz,BER = 10
Wanted signal at –67 dBm, modulated interferer at ±3
–3
MHz, BER = 10
Wanted signal at –67 dBm, modulated interferer at ±4
–3
MHz, BER = 10
Wanted signal at –67 dBm, modulated interferer at ≥ ±5
–3
MHz, BER = 10
Wanted signal at –67 dBm, modulated interferer at image
–3
frequency, BER = 10
Note that Image frequency + 1 MHz is the Co- channel
–1 MHz. Wanted signal at –67 dBm, modulated interferer
at ±1 MHz from image frequency, BER = 10
30 MHz to 2000 MHz
2003 MHz to 2399 MHz
2484 MHz to 2997 MHz
3000 MHz to 12.75 GHz
Wanted signal at 2402 MHz, –64 dBm. Two interferers
at 2405 and 2408 MHz respectively, at the given power
level
Measurement in a 50-Ω single-ended load.
Measurement in a 50-Ω single-ended load.
Differential mode. Measured at SMA connector, BER =
–3
10
Differential mode. Measured at SMA connector, BER =
–3
10
Difference between the incoming carrier frequency and
the internally generated carrier frequency
Difference between incoming data rate and the internally
generated data rate (37-byte packets)
Product Folder Links:
= 25 °C, V = 3.0 V, f
c DDS RF
MIN
–3
–3
CC2652PSIP
= 2440 MHz with
TYP MAX
(2)
46 / 45
(2)
49 / 45
35
(2)
4 / 46
–96
> 5
> (–350 / 350)
> (–650 / 750)
–6
(2)
7 / 4
(2)
39 / 33
(2)
36 / 40
(2)
36 / 45
40
33
(2)
4 / 41
–10
–18
–12
–2
–42
< –59
< –47
70
±4
–90
> 5
> (–500 / 500)
> (–700 / 750)
Copyright © 2022 Texas Instruments Incorporated
www.ti.com
UNIT
dB
dB
dB
dB
dBm
dBm
kHz
ppm
dB
dB
dB
dB
dB
dB
dB
dB
dBm
dBm
dBm
dBm
dBm
dBm
dBm
dB
dB
dBm
dBm
kHz
ppm