Zigbee And Thread - Ieee 802.15.4-2006 2.4 Ghz (Oqpsk Dsss1:8, 250 Kbps) - Tx; Timing And Switching Characteristics - Texas Instruments SimpleLink CC2652PSIP Manual

CC2652PSIP
SWRS263A – FEBRUARY 2021 – REVISED JUNE 2022

8.13 Zigbee and Thread - IEEE 802.15.4-2006 2.4 GHz (OQPSK DSSS1:8, 250 kbps) - TX

Measured on the CC2652xSIP-EM
DC/DC enabled and high power PA connected to V
All measurements are performed at the antenna input with a combined RX and TX path, except for high power PA which is
measured at a dedicated antenna connection. All measurements are performed conducted.
PARAMETER
General Parameters
Max output power, high
power PA, 10 dBm Differential mode, delivered to a single-ended 50-Ω load through a balun
(1) (2)
configuration
Output power
programmable range,
Differential mode, delivered to a single-ended 50-Ω load through a balun
high power PA, 10 dBm
configuration
Max output power,
Differential mode, delivered to a single-ended 50-Ω load through a balun
(3)
regular PA
Output power
programmable range, Differential mode, delivered to a single-ended 50-Ω load through a balun
regular PA
Spurious emissions and harmonics
f < 1 GHz, outside restricted
bands
Spurious emissions,
f < 1 GHz, restricted bands ETSI
high-power PA, 10 dBm
(1)
configuration
f < 1 GHz, restricted bands FCC
f > 1 GHz, including harmonics
Harmonics, Second harmonic
high-power PA, 10 dBm
Third harmonic
configuration
f < 1 GHz, outside restricted
bands
Spurious emissions,
f < 1 GHz, restricted bands ETSI
(3)
regular PA
f < 1 GHz, restricted bands FCC
f > 1 GHz, including harmonics
Second harmonic
Harmonics,
(3)
regular PA
Third harmonic
IEEE 802.15.4-2006 2.4 GHz (OQPSK DSSS1:8, 250 kbps)
Error vector magnitude,
high power PA, 10 dBm +10 dBm setting
configuration
Error vector magnitude,
+5 dBm setting
Regular PA
(1) For FCC 15.247 Part 15 (US) Channel 16 is disabled and not available for use.
(2) To meet the ETSI EN 300 328 (Europe) 10dBm/MHz Power Spectral Density (PSD) requirement, output power is limited to 7 dBm and
6 dBm when using a max antenna gain of 1.9 dBi and 3.3 dBi, respectively.
(3) To meet the FCC 15.247 Part 15 (US) Band Edge requirement, Channel 16 is reduced by 3 dBm.

8.14 Timing and Switching Characteristics

8.14.1 Reset Timing
nRESET low duration
18 Submit Document Feedback
reference design with T = 25 °C, V
c
unless otherwise noted.
DDS
TEST CONDITIONS
+10 dBm setting
+5 dBm setting
PARAMETER
Product Folder Links:
= 3.0 V, f = 2440 MHz with
DDS RF
Copyright © 2022 Texas Instruments Incorporated
CC2652PSIP
www.ti.com
MIN TYP MAX UNIT
10.0 dBm
5 dB
5 dBm
26 dB
< -36 dBm
< -47 dBm
< -55 dBm
-42 dBm
< -42 dBm
< -42 dBm
< -36 dBm
< -47 dBm
< -55 dBm
< –42 dBm
< -42 dBm
< -42 dBm
2 %
2 %
MIN TYP MAX UNIT
1 µs