Roland DiscLab CDX-1 Owner's Manual page 250

Mastering Tools parameter list
COMP (Compressor)
Effect On/Off (Effect On/Off)
Low Threshold (Low Threshold)
Mid Threshold (Middle Threshold)
Hi Threshold (High Threshold)
Low Ratio (Low Ratio)
Mid Ratio (Middle Ratio)
High Ratio (High Ratio)
Low Attack (Low Attack)
Mid Attack (Middle Attack)
High Attack (High Attack)
Low Release (Low Release)
Mid Release (Middle Release)
High Release (High Release)
Adjust the volume of the low, mid, and high frequency ranges, and mix them.
MIX (Mixer):
Low Level (Low Level)
Mid Level (Middle Level)
High Level (High Level)
Prevents distortion by suppressing signals at High levels.
LMT (Limiter):
Effect On/Off (Effect On/Off)
Threshold (Threshold)
Attack (Attack)
Release (Release)
OUT (Output): Provides settings concerning overall output.
Level (Level)
Soft Clip (Soft Clip)
Dither (Dither)
*1 If "Low Type" or "High Type" is set to "SHELV" (Shelving Type), the setting for "Lo Q "or "High Q" is invalid.
*2 With Compressor (COMP), the level is automatically adjusted to the optimal with the settings for "Threshold" and "Ratio". Setting
"Attack" to a relatively long time may cause distortion. For this reason, a margin of -6 dB is provided. Adjust the Mixer (MIX) level as
required.
22
: Compressor the entire output signals when the input volume exceeds a specified value.
*2
OFF, ON
-24–0 dB
-24–0 dB
-24–0 dB
1:1.0–1:16.0, 1:INF
1:1.0–1:16.0, 1:INF
1:1.0–1:16.0, 1:INF
0–100 ms
0–100 ms
0–100 ms
50–5000 ms
50–5000 ms
50–5000 ms
-80–+6 dB
-80–+6 dB
-80–+6 dB
OFF, ON
-24–0 dB
0–100 ms
50–5000 ms
-80– +6 dB
OFF, ON
OFF, 8–24 bit
This parameter turns the compressor effects on/off.
This parameter sets the volume at which the compressor for the low
frequency band starts working.
This parameter sets the volume at which the compressor for the middle
frequency band starts working.
This parameter sets the volume at which the compressor for the high
frequency band starts working.
This parameter sets the ratio at which the output in the low frequency band
is suppressed when the input level has exceeded the low threshold level.
This parameter sets the ratio at which the output in the middle frequency band
is suppressed when the input level has exceeded the middle threshold level.
This parameter sets the ratio at which the output in the High frequency band is
suppressed when the input level has exceeded the High threshold level.
This parameter sets the time until when the low frequency band compressor
starts working after the input level has exceeded the low threshold level.
This parameter sets the time until when the middle frequency band compressor
starts working after the input level has exceeded the middle threshold level.
This parameter sets the time until when the High frequency band compressor
starts working after the input level has exceeded the High threshold level.
This parameter sets the time until when the low frequency band compressor
stops working after the input level has dropped below the low threshold level.
This parameter sets the time until when the middle frequency band compressor
stops working after the input level has dropped below the middle threshold level.
This parameter sets the time until when the High frequency band compressor
stops working after the input level has dropped below the High threshold level.
This parameter sets the volume in the low frequency band after passing
through the expander and compressor.
This parameter sets the middle frequency band volume after passing
through the expander and compressor.
This parameter sets the volume in the High frequency band after passing
through the expander and compressor.
This parameter turns the limiter effects on/off.
This parameter sets the volume at which the limiter starts working.
This parameter sets the time until when the limiter starts working after the
input level has exceeded threshold level.
This parameter sets the time until when the limiter stops working after the
input level drops below the threshold level.
This parameter sets the overall volume after passing through the limiter.
By turning this ON, suppresses conspicuous distortion that may occur
when the effect of compressor/limiter has been applied excessively.
This parameter smooths the transition where the sound disappears.