IAI GOX-2402M-USB User Manual page 72

Default level
Black Level
Video level adjustment range
adjustment
Resolution adjustment
Gain Manual adjustment range
adjustment
adjustment Auto gain
WhiteBalanceGain
White
BalanceWhiteAuto
balance
Photometry area
Adjustment range
Detection
Blemish
correction
Correction
Correctable pixels
ALC
Gamma
LUT
Vibration resistance
Impact resistance
6-pin Connector
Power
supply
USB BUS Power
Lens mount
Flange back
Optical filter
Verified performance temperature / humidity
Storage temperature / humidity
Regulations
Dimensions (housing)
Weight
Package contentsCamera
Optional accessories (not supplied)
Design and specifications are subject to change without notice.
Approximately 30 minutes of warm-up are required to achieve these specifications.
Caution
About the verified performance temperatureMake sure the following temperature conditions is
met when operating the unit.
1) The camera's internal temperature sensor detects temperatures of 77 °C or less during
operation.
If the above temperature conditions are exceeded, take measures to dissipate heat according to
your installation environment and conditions.
Input range
4.3 W（typ.）(at 12 V input, default setting, 25 ℃ environment）
Consumption
4.9 W（max.）
Input range
4.2 W（typ.）(default setting, 25 ℃ environment）
Consumption
4.7. W（max.）
body (1)
Sensor protection cap (1)
Dear Customer (sheet) (1)
MP-43 tripod mount
— 72 —
8LSB@8bit
DigitalAll : -133 ~ +255 LSB @12bit
DigitalRed : -64 ~ +64 LSB @12bit
DigitalBlue : -64 ~ +64 LSB @12bit
1LSB@12bit
AnalogAll : 0dB 〜 42dB
DigitalRed : -7dB 〜 15dB
DigitalBlue : -7dB 〜 15dB
Off, Continuous, Once
DigitalRed, DigitalBlue : -7dB 〜 15dB
Off, Continuous, Once,
Preset3200K, Preset5000K, Preset6500K, Preset7500K
16 (4 x 4) Area
3000K 〜 9000K
Detect white blemishes using threshhold values
(100 steps available)
(black blemish correction performed only at factory)
Interpolation using adjacent pixels
(continuous blemishes not corrected)
256 pixels
Video level adjusted automatically using AGC and ASC
0.45, 0.5, 0.55, 0.6, 0.65, 0.75, 0.8, 0.9, 1.0
(9 steps available)
OFF︓γ＝ 1.0、ON ＝ 257 points can be set
10G（20 Hz 〜 200 Hz X-Y-Z direction）
80G
DC ＋ 10 V 〜＋ 25 V （Via input terminal）
C-mount
Lens mount protrusion length of 9 mm or less is supported
17.526, tolerance: 0 mm to -0.05 mm
IR cut filter (color model only)
­ 5℃〜＋ 45℃ / 20％〜 80％ (non-condensing)
(* It may change depending on the installation environment. Please refer to the Caution.)
­ 25℃〜＋ 60℃ / 20％〜 80％ (non-condensing)
CE(EN 55032:2015 and EN 55035:2017), FCC class A part 15,
29 × 29 × 41.5 mm (WHD) (excluding mount protrusions)
62 g
Go-X Series USB3 Vision I/F
9