Table of Contents
Advertisement
Item
j) AutoLevelControl
ALCControlReference
ALCControlChannel
ALCReference
ALCAreaSelector
ALCAreaEnable
ALCAreaEnableAll
ALCControlRatio
AutoShutterControlExposureMin
AutoShutterControlExposureMax
AutoGainControlGainRawMin
AutoGainControlGainRawMax
ALCStatus
AutoControlStatus
k) ImagingControl
VideoProcessBypassMode
l) ShadingConrol
ShadingCorrectionMode
ShadingMode
PerformShadingCalibration
ShadingDetectResult
Setting range
Default value
0: Peak Channel,
1: Selected Channel
1: Selected Channel
0:Red,
1: Green
1:Green,
2:Blue
30〜95
50
―
Low Right
True, False
True
True, False
True
1〜100
90
100 〜
100
―
ー
100 〜
100
〜 12600
12600
0: Off,
0:Off
2: ASC,
3: AGC
―
Idle
Off, On
Off
0:Flat Shading
0:Flat Shading
1:Color Shading
0:Off,
2:User1
0:Off
3:User2, 4:User3
ー
ー
ー
ー
Configure Auto Level Control settings.
Set the target level for ALC. (unit: %)
Select the area for which to configure [ALCAreaEnable].
[Setting range]
0:Low Right,
1:Low Mid-Right,
4:Mid-Low Right,
5:Mid-Low Mid-Right,
8:Mid-High Right, 9:Mid-High Mid-Right, 10:Mid-High Mid-Left, 11:Mid-High Left
12:High Right,
13:High Mid-Right,
Enable/disable the photometry area selected in [ALCAreaSelector].
True: Operate ALC with all areas designated as photometry areas, regardless of the
individual enabled/disabled photometry area states configured in [ALCAreaSelector].
False: Operate ALC according to the individual enabled/disabled photometry area states
configured in [ALCAreaSelector].
Set the response speed. (100 is the fastest.)
Set the minimum value for the ExposureAuto(ASC) control range.
Set the maximum value for the ExposureAuto(ASC) control range.
Set the minimum value for the GainAuto(ASC) control range.
Set the maximum value for the GainAuto(ASC) control range.
Allows confirmation of the current operation area during ALC operation.
Allows confirmation of the AGC, ASC, and AWB convergence status.
[Status]
1:ExecutingASC, 2:ExecutingAGC, 3:ExecutingASCandAGC, 4:ExecutingAWB
5:ExecutingASCandAWB, 6:ExecutingAGCandAWB, 7:ExecutingASCandAGCandAWB,
8:Convergent, 9:ConditionError, 255:Idle
Configure settings for other JAI functions.
Enable/disable VideoProcessBypass mode.
Configure shading correction settings.
Select the shading correction method.
Set the area to which to save shading correction data.
When this is set to [Off], shading correction data is not saved.
Execute shading correction.
This command can not be executed under the following conditions.
・When no image is output
・Outputting TestPattern
・In Sequencer mode
・When the ROI setting is under the following conditions
(Width or Height is less than 128)
・In Decimation mode
・In Binning mode
Display the shading correction results.
[results]
0: Condition Error, 1: TooDark, 2: TooBright, 3: Correction Limit, 4: Complete
— 65 —
Go-X Series USB3 Vision I/F
Description
2:Low Mid-Left,
3:Low Left
6:Mid-Low Mid-Left,
7:Mid-Low Left
14:High Mid-Left,
15:High Left
Advertisement
Table of Contents
