Page 1
User Manual 020-001835-02 CP2306-RGBe, CP2308-RGBe, CP2310-RGBe...
Page 2
Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material.
Page 11
For protection from ultraviolet radiation, keep all product housings intact during operation. • UV EXPOSURE! Protective UV safety glasses with side shields and Christie approved protective safety clothing must be worn when performing optical adjustments or servicing the product. •...
Page 12
Safety precautions Caution! If not avoided, the following could result in minor or moderate injury. • Only Christie qualified technicians are permitted to open product enclosures. • Install the product near an easily accessible AC receptacle. • For products containing surge suppressors, you must adhere to the installation and power requirements.
Page 13
Learn about the labels that may be used on the product. Labels on your product may be yellow or black and white. Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power.
Page 14
To prevent fire or shock hazards, do not expose this product to rain or moisture. Do not alter the power plug, overload the power outlet, or use it with extension cords. Do not remove the product enclosure. Only Christie qualified technicians are authorized to service the product. Electrical Hazard Risk of electric shock.
Page 17
For complete production documentation and technical support, go to www.christiedigital.com. For installation, setup, and user information, see the product documentation available on the Christie Digital Systems USA Inc. website. Read all instructions before using or servicing this product. 1. Access the documentation from the Christie website: Go to https://bit.ly/3lkZ48l or...
Page 24
Inverted Front Projection from behind the audience with the projector in an inverted position (upside down). Inverted positioning is not supported for CP2306-RGBe, CP2308-RGBe, CP2310-RGBe projectors. For more information, see the CP2306-RGBe, CP2308-RGBe, CP2310-RGBe Installation and Setup Manual (P/N: 020-103451-XX).
Page 27
Learn how to create new user accounts, how to modify the properties of those accounts, and how to remove the accounts. A user account is a set of credentials consisting of both a username and password that allows access to a projector setting. This table lists the Christie touch panel access permissions. Permission Description •...
Page 32
The marriage wizard requires you to confirm that the IMB has not been tampered with. 1. Install the IMB in the available slot on the projector. For more information, see the Christie IMB-S3 Installation and Setup Manual (P/N: 020-102582-XX) or the documentation provided by the IMB manufacturer.
Page 42
3D Line Interleaved: The left eye and right eye data are sent on alternating lines. 3D Sync Input Mode is not required when using the Christie IMB. For GDC IMB devices, the recommended setting is 3D Line Interleaved. ILS File The ILS file associated with the channel.
Page 53
If the image suffers from slight keystone effect, it can be corrected with electronic cropping. If the keystone effect is severe, you can unevenly adjust the feet to compensate for projector tilt. Christie recommends using lens offset to align the center of the image to the center of the screen before you correct the keystone effect.
Page 55
When adjusting boresight, you must maintain the boresight distance from the lens to the prism plane set by Christie. For example, when you move the top screw outward, turn the bottom two boresight screws to maintain the overall distance.
Page 56
When adjusting boresight, you must maintain the boresight distance from the lens to the prism plane set by Christie. For example, when you move the top screw outward, turn the bottom two boresight screws to maintain the overall distance.
Page 58
Contact your Christie accredited service technician to correct DMD convergence issues. Learn how to align the fold mirror with the optical system to correct an image with missing or shadowy corners or edges.
Page 71
6. In the Eye Selection column, select Right or Left. Complete this procedure on the master projector. Content synchronization is supported for Christie network attached storage (NAS) devices only. To synchronize content, you must also enable the Multi-Projector Control option on the master projector.
Page 74
Delays the execution of a macro Disable Subtitle Disables subtitles for the current content and onward Moves content forward by the time specified These are the available built-in commands for the Christie ACT: Command Description Buzzer Activates the buzzer for the specified time (in milliseconds)
Page 87
Typically, optical components do not need to be cleaned frequently if they are installed and operated in a location that meets or exceeds the environmental standard recommended by Christie. Christie recommends that all cinema projectors are installed and operated in an environment that meets or exceeds Underwriters Laboratories (UL) standard 609.50 Pollution Degree 2 and ISO Class 9 Standard for Office Environments.
Page 88
Check the condition of the card cage air filter monthly. Clean or replace the card cage air filter sooner if you are operating the projector in a dusty or dirty environment. The filter is located on the left side of the projector behind the air filter cover. Use only high efficiency Christie approved filters.
Page 92
If the POWER LED is green and additional LEDs are lit on the F-MAIN faceplate, record the color combination of the faceplate LEDs after they have been powered for at least 30 seconds. You can then provide the color combination information to Christie technical support. •...
Page 93
The projector image flickers, contains shadows, or dim. Resolution • Verify that the douser is open. • A fold mirror or integrator rod misalignment could exist. Contact your Christie qualified service technician to resolve the issue. When the projector is turned on, nothing is displayed. Resolution •...