1. Manuals
  2. Brands
  3. Christie Manuals
  4. Projector
  5. CP2308-G
  6. Installation and setup manual

Christie CP2308-G Installation And Setup Manual

Hide thumbs Also See for CP2308-G:
Table of Contents

Advertisement

Quick Links

Download this manual
Installation and Setup Guide
020-102866-01
CP2308-G

Advertisement

Table of Contents
loading

Related Manuals for Christie CP2308-G

Summary of Contents for Christie CP2308-G

  • Page 1 Installation and Setup Guide 020-102866-01 CP2308-G...
  • Page 2 The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.

  • Page 3: Table Of Contents

    Activating the Intelligent Lens System........24 CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...
  • Page 4 Environmental........... . 30 CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...

  • Page 5: Safety Precautions

    Learn about the safety precautions related to the Christie CP2308-G projector. Disclaimer statement The CP2308-G subassembly is not a functional product. Hazard labels must be placed on the end product. The end product must meet the regulatory compliance requirements for China.

  • Page 6: Light Source Safety Precautions For The End Product

    • SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product by Christie qualified technicians or electricians before it can be connected to power. • SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by Christie.

  • Page 7: Light Intensity Hazard Distance

    Learn about the labels that may be used on the product. Labels on your product may be yellow or black and white. General hazards Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power. Fire and Shock Hazard To prevent fire or shock hazards, do not expose this product to rain or moisture.

  • Page 8: Mandatory Action

    Safety precautions Explosive material hazard. To avoid personal injury, disconnect all power sources before performing maintenance or service, and wear Christie-approved protective clothing. Bright light hazard. To avoid personal injury, never look directly at the light source. Pinch hazard. To avoid personal injury, keep hands clear and loose clothing tied back.

  • Page 9: Introduction

    Introduction This manual is intended for professionally trained operators of Christie high-brightness CP2308-G projection systems. For complete production documentation and technical support, go to www.christiedigital.com. Projector components - front Learn about the components on the front of the projector. Touch panel...

  • Page 10: Projector Components - Rear

    • Power cord • Touch panel • Convergence tool • Stacking kit, including stacking cups, locking brackets, and required screws CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...

  • Page 11: Installation And Setup

    1. To adjust the height of the projector, loosen the lock nut on the adjustable feet on the bottom of the projector. 19 mm (0.75 in.) wrench CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...

  • Page 12: Stacking Projectors

    2. Extend or retract the feet. 3. When the adjustment is correct, tighten the lock nut. Stacking projectors To stack CP2308-G projectors, use the stacking kit provided. The stacking kit includes these parts: Locking bracket (quantity 4) Stacking cup (quantity 4) M6 screw (quantity 4) When stacking projectors, the optical axis of the projectors must be parallel to one another.
  • Page 13 (A) and align vertically (B). CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...
  • Page 14 Turn the locking bracket so the flanges of the locking bracket fit tightly below the stacking cup tabs. c) Repeat steps a and b to install the three remaining locking brackets CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...

  • Page 15: Installing The Touch Panel

    3. While supporting the touch panel, fit the other end of the touch panel mounting arm over the ball joint on the rear panel or electronics side of the projector. CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...

  • Page 16: Installing The Lens

    The lens seals the projection head, preventing contaminants from entering the main electronics area. Before installing the lens, ensure that you turn off and unplug the projector. CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...
  • Page 17 4. Insert and tighten the two lens mount hex screws shipped separately with the projector. 5. Lock the lens assembly in place with a hex key. 6. Replace the lens surround. CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...

  • Page 18: Connecting Power

    • SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product by Christie qualified technicians or electricians before it can be connected to power. • SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by Christie.

  • Page 19: Turning The Projector On Or Off

    You must complete marriage to display content and to comply with the Digital Cinema Initiatives (DCI) specification. You cannot complete marriage remotely. 1. In the left navigation menu, tap Service Setup > Marriage Setup. CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...
  • Page 20 Installation and setup 2. Tap Start and complete the Marriage Setup wizard. 3. Tap Finish. CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...

  • Page 21: Connecting Devices To The Projector And Establishing Communication

    • FIPS—The LED is green when the FIPS (Federal Information Processing Standards Publications) security status is operating correctly. If the LED is red, an error has occurred. Restart the Christie IMB. If the LED remains red, return the Christie IMB to Christie Digital Systems USA Inc.

  • Page 22: Connecting The Projector To A Computer

    1. To connect the main input card of the projector, connect an Ethernet cable to the Management Ethernet port on the projector and the other end to your computer. CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...

  • Page 23: Connecting Devices To The 3D Sync Terminal

    2. To communicate with the projector, add the projector to the same network as the computer. Connecting devices to the 3D sync terminal For information on connecting devices to the 3D sync terminal, see the CP2308-G User Manual. CP2308-G Installation and Setup Guide 020-102866-01 Rev.

  • Page 24: Adjusting The Image

    CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...

  • Page 25: Adjusting Vertical Boresight

    When adjusting boresight, you must maintain the boresight distance from the lens to the prism plane set by Christie. For example, when you move the top screw outward, turn the bottom two boresight screws to maintain the overall distance.

  • Page 26: Adjusting Horizontal Boresight

    Caution! If not avoided, the following could result in minor or moderate injury. • This procedure must be performed by Christie qualified technicians. Typically, horizontal boresight does not require adjustment. It should only be adjusted if a large horizontal angular offset to the screen is required.
  • Page 27 Adjusting the image When adjusting boresight, you must maintain the boresight distance from the lens to the prism plane set by Christie. For example, when you move the top screw outward, turn the bottom two boresight screws to maintain the overall distance.

  • Page 28: Adjusting Digital Micromirror Device Convergence

    Normally, the three colors should overlap precisely to form pure white lines throughout the image and one or more poorly converged individual colors may appear adjacent to some or all of the lines. Contact your Christie accredited service technician to correct DMD convergence issues. Adjusting the fold mirror Learn how to align the fold mirror with the optical system to correct an image with missing or shadowy corners or edges.

  • Page 29: Calibrating The Color

    Learn how to create Measured Color Gamut Data (MCGD) files to correct on-screen colors. Using a colorimeter, measure the colors displayed on the screen from the center of the audience viewing location. For more information, see the CP2308-G User Manual. CP2308-G Installation and Setup Guide 020-102866-01 Rev.

  • Page 30: Regulatory

    (01/2016) on the control of pollution caused by electronic information products, hazardous substances concentration limits (GB/T 26572 - 2011), and the applicable product marking requirement (SJ/T 11364 - 2014). CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...
  • Page 31 International packaging recycling mark requirements. • EU Directive (94/62/EC) on packaging and packaging waste • China packaging recycling mark standard (GB18455-2010) CP2308-G Installation and Setup Guide 020-102866-01 Rev. 1 (05-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...
  • Page 32 Corporate offi ces Worldwide offi ces Christie Digital Systems USA, Inc. Australia Germany Republic of South Africa United Kingdom Cypress ph: +61 (0) 7 3624 4888 ph: +49 2161 664540 ph: +27 (0)11 510 0094 ph: +44 (0) 118 977 8000...

Table of Contents