Page 1
Installation and Setup Guide 020-102773-02 CP2320-RGB...
Page 2
The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.
Safety precautions Learn about the safety precautions related to the Christie CP2320-RGB projectors. General safety precautions Read all safety and warning guidelines before installing or operating the projector. Warning! If not avoided, the following could result in death or serious injury.
• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product by Christie qualified technicians or electricians before it can be connected to power. • SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning, removing components, or opening any enclosure.
Page 8
• F—Represents the side view of the projector. The following table lists the hazard distance for the Christie projector lens with the zoom adjusted to its most hazardous position. For US market only, hazard distances based upon FDA guidance document 1400056, Classification and Requirements for Laser Illuminated Projectors (LIPs), dated February 18, 2015.
Learn about the labels that may be used on the product. Labels on your product may be yellow or black and white. General hazards Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power. Fire and Shock Hazard To prevent fire or shock hazards, do not expose this product to rain or moisture.
For complete production documentation and technical support, go to www.christiedigital.com. Product documentation For installation, setup, and user information, see the product documentation available on the Christie Digital Systems USA Inc. website. Read all instructions before using or servicing this product.
Installing and setting up Learn how to position and install the projector. Site requirements To safely install and operate the CP2320-RGB projector, the installation location must meet these minimum requirements. Physical operating environment • Ambient temperature (operating) 10°C to 35°C (50°F to 95°F) •...
• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product by Christie qualified technicians or electricians before it can be connected to power. • A certified electrician must be present during installation to ensure the installation meets the local electrical code.
If the projector is not connected to AC power with breakers in the ON position, you cannot turn the touch panel on. Projector power modes The CP2320-RGB projectors track laser operation hours for the laser optical sub-system (LOS). The projector operates with the following power modes: CP2320-RGB Installation and Setup Guide 020-102773-02 Rev.
You must complete marriage to display content and to comply with the Digital Cinema Initiatives (DCI) specification. For more information on marriage, refer to CP2320-RGB User Guide (P/N: 020-102769-XX) You cannot complete marriage remotely. 1. In the left navigation menu, tap Service Setup > Marriage Setup.
AES3 port for digital audio output. Linear Time Code (LTC) output. Output for multi-projector playback. Input for multi-projector playback (Christie IMB to Christie IMB only). SM and FIPS LED status indicators CP2320-RGB Installation and Setup Guide 020-102773-02 Rev. 1 (05-2019) Copyright 2019 Christie Digital Systems USA, Inc.
Connecting the projector to a network The CP2320-RGB projectors can be connected to various media devices and wired networks. For detailed information on connecting the projector to a device or network, see the CP2320-RGB User Guide (P/N: 020-102769-XX). CP2320-RGB Installation and Setup Guide 020-102773-02 Rev.
For Red, Green, and Blue power levels, system stability may be affected if levels are set below the minimum (MIN) power limit shown. To ensure color and brightness are held at the required levels for your installation, Christie ™...
System stability may be affected if you set a power level below the minimum power level recommended. When setting the Red or Green power level, Christie recommends setting a level below the maximum (MAX) limit shown. A value below the maximum limit ensures an optimal brightness that can be maintained over time.
Learn how to adjust image geometry so it displays correctly. Calibrating the Intelligent Lens System On the CP2320-RGB projectors, the Intelligent Lens System (ILS) is activated by default. Use the Auto Calibrate feature of the ILS to find and compensate for motor backlash, and to determine the movement range for the currently installed lens.
Adjusting the integrator and fold mirror Extreme misalignment of projection optics can cause permanent damage to critical optical components. Only Christie qualified technicians can perform internal optical adjustments. Notice. If not avoided, the following could result in property damage. •...
The next steps may include creating a Measured Color Gamut Data (MCDG) file and configuring a ™ Pureformity Color Technology (PCT) file to achieve optimal color and brightness uniformity. For more information on managing color settings, see the CP2320-RGB User Guide (P/N: 020-102769- XX). CP2320-RGB Installation and Setup Guide 020-102773-02 Rev. 1 (05-2019) Copyright 2019 Christie Digital Systems USA, Inc.
Page 46
Corporate offi ces Worldwide offi ces Christie Digital Systems USA, Inc. Australia Germany Republic of South Africa United Kingdom Cypress ph: +61 (0) 7 3624 4888 ph: +49 2161 664540 ph: +27 (0)11 510 0094 ph: +44 (0) 118 977 8000...