Eca Evs-Xl - Matrox Mura IPX Series System Builder's Manual

ECA EVS-XL

Validated
Maximum number of cards
supported
Maximum supported
Mura IPX Series
Maximum supported
D-Series
Motherboard
Chipset
Processor
Heatsink (for CPU)
System BIOS version
System memory
Chassis
Power supply
PCIe expansion slots
Notes
Configurations
Slot
P1PCIE_1
P2PCIE_1
P2PCIE_2
P3PCIE_1
P3PCIE_2
28 Matrox Display Wall – System Builder's Guide
D-Series based controllers
Yes
14
13
4
Advantech PCE-7131 (SHB)
Advantech PCE-5B12-00A1 (Backplane)
Intel C246
Intel® Xeon®E-2278GE CPU@ 3.30 GHz, or
Intel® Core™ i7-9700E CPU @ 2.60 GHz
2U CPU cooler
5.13, 2020-04-09
32 GB DDR4 ECC Memory (Intel Xeon E-2278GE)
32 GB DDR4 non-ECC memory (Intel i7-9700E)
5U (P/N: GHI-528)
1550 W redundant power supply (P/N: Zippy MTW4-5F50V3H)

17 PCIe x16 3.0 slots (x16 mechanical, x16 electrical)

1 PCIe x16 3.0 slot (x16 mechanical, x4 electrical)

The dust protection sponge filter in the front door must be removed for proper system ventilation.

If you use a wired mesh filter in the front door, the ambient temperature must not exceed 40 degrees C.
Filter requires a 18 x18 size 304 stainless steel wire mesh.

Once the add-in cards are installed in the system, the baffle must be placed on the top for proper air
circulation. The baffle must be used only with small clips to properly secure the add-in cards with the board
retainer bar.

Requires 4 x 92 mm x 92 mm x 2 5mm 102 CFM chassis fans running at full speed.

The smart fan must be disabled to run the chassis fans at full speed. In the system BIOS, go to
 
HW Monitor Tab SYSFAN1 smartfan
Ensure to have the following settings for GPU. Go to the system BIOS main page 


(SA) Configuration Graphics Configuration
 Primary Display 
AUTO
 Internal Graphics

AUTO

In the system BIOS main page, go to
 and select
Assignment Enabled
 The P1PCIE1 x4 slot is unusable due to adjacent SHB slot.

The P2PCIE1 x16 and P2PCIE2x16 slots are unusable due to mechanical conflict with the SHB CPU fan.
 The P5PCIE5 x16 slot is unusable due to presence of red push button in the bracket slot area.

Card placement shown in the configuration table must be followed for better system ventilation.

Any unused slots must be installed with solid brackets for proper system ventilation.

On-board console support with D-Series controller. Requires 3.05 or later drivers.
D-Series based controller
Main
N/A
N/A
N/A
MURAIPXI-E4JF
MURAIPXI-E4JF
Third-party based controllers
No foreseeable compatibility issues
setting  and select
DISABLE
 and select:
(select for Console)
Enabled

Chipset System Agent (SA) Configuration
.
Third-party based controller
Option Main
N/A N/A
N/A N/A
N/A N/A
A Third-party graphics hardware
A MURAIPXI-E4JF
.

Chipset System Agent

Above 4GB MMIO BIOS
Option
N/A
N/A
N/A
A
A
Advanced