Advertisement
These are the original version controlled Henny Penny instructions for Evolution Elite
Gas (EEG) model 253, 254 (EEG 25x). This manual is available on the Henny Penny
Public website (www.hennypenny.com). Read these instructions completely prior to
installation and operation of this appliance to ensure compliance to all required
installation, operation and safety standards. Read and obey all safety messages to
avoid damage to the appliance and personal injury.
PROPER USE AND SERVICE
This appliance is intended for commercial use in kitchens of restaurants, bakeries,
hospitals, etc. but not for the continuous mass production of food such as in a factory
setting. During use the units airborne A-weighted emission sound pressure is below
70 db(A). All repairs must be performed by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
ELECTRICAL REQUIREMENTS
Always use strain relief. The provided power cord must be installed with a strain relief
in a way that if the strain relief fails, wires L1, L2, L3 and N must draw taunt and fail
first. If the supplied power cord or an existing one becomes damaged, do not use it;
rather, replace it with a known good power cord with a wire size of 4mm, to be wired to
the terminal block. If a flexible power cord is used, it must be HO7RN type.
Additionally the power cord must be oil-resistant, sheathed, flexible cable, no lighter
than ordinary polychloroprene or other equivalent synthetic elastomer-sheathed cord.
The power cord must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard. It's recommended that a 30 MA rated
protective device such as a residual current circuit breaker (RCCB) or ground fault
circuit interrupter (GFCI) be used on the fryer circuit. This appliance is not intended to
be operated by means of an external timer or a separate remote control system. Do
not disconnect the ground (earth) plug. This fryer must be adequately and safely
grounded (earthed) or electrical shock could result. Refer to local electrical codes for
correct grounding (earthing) procedures or in absence of local codes, with The
National Electrical Code, ANSI/NFPA No. 70-(the current edition).
vi
•
T T h h i i s s f f r r y y e e r r m m u u s s t t b b e e i i n n s s t t a a l l l l e e d d a a n n d d u u s s e e d d i i n n a a w w a a y y t t h h a a t t
w w a a t t e e r r d d o o e e s s n n o o t t c c o o n n t t a a c c t t t t h h e e o o i i l l w w h h i i c c h h c c a a n n c c a a u u s s e e
s s p p l l a a s s h h i i n n g g a a n n d d b b o o i i l l i i n n g g o o v v e e r r o o f f o o i i l l a a n n d d s s t t e e a a m m l l e e a a d d i i n n g g
t t o o p p e e r r s s o o n n a a l l i i n n j j u u r r y y ; ; e e x x c c l l u u d d e e s s n n o o r r m m a a l l p p r r o o d d u u c c t t
m m o o i i s s t t u u r r e e . .
•
B B u u r r n n r r i i s s k k ! ! D D o o n n o o t t m m o o v v e e t t h h e e f f r r y y e e r r o o r r f f i i l l t t e e r r d d r r a a i i n n p p a a n n
w w h h i i l l e e c c o o n n t t a a i i n n i i n n g g h h o o t t o o i i l l . . P P e e r r s s o o n n a a l l i i n n j j u u r r y y o o r r s s e e r r i i o o u u s s
b b u u r r n n s s c c a a n n r r e e s s u u l l t t f f r r o o m m s s p p l l a a s s h h i i n n g g h h o o t t o o i i l l . .
Advertisement
