Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Henny Penny HB-11
Summary of Contents for Henny Penny HB-11
- Page 1 Henny Penny Hand Breader/Sifter Model HB-11 TECHNICAL MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Section Page Section 1. MAINTENANCE ..................... 1-1 1-1. Introduction...................... .1-1 1-2. Safety ....................... 1-1 1-3. Replacement of Belt ..................1-2 1-4. Replacement of Mandrel..................1-2 1-5. Replacement of Motor..................1-3 1-6. Replacement of Switch ..................1-4 1-7. Replacement of Rod End Bearing ..............1-5 1-8. -
Page 3: Introduction
Outlined below are step by step procedures when replacing parts becomes necessary. Refer to exploded drawing in this manual. The only way to ensure safe operation of the Henny Penny Hand 1-2. SAFETY Breader/Sifter is to fully understand the proper installation, operation, and maintenance procedures. -
Page 4: Replacement Of Belt
1. Remove all equipment (breading lugs, back splash, dip pot, etc.) 1-3. REPLACEMENT OF BELT from top of unit. 2. Remove top (28) by lifting from unit. 3. Using a #2 Phillips screwdriver, remove two screws (17) from cover plate assembly (16), and slide cover plate assembly out towards the sifter basket. -
Page 5: Replacement Of Motor
4. Loosen hex nuts on the adjustable foot (10), move motor, 1-4. REPLACEMENT OF and loosen belt. Remove belt. MANDREL (Continued) 5. Using a 5/16" Allen wrench, remove set screw (62) from driven pulley and remove pulley (53). 6. Turn mandrel shaft (52) until the eccentric (49) and rod end bearing (46) are accessible. -
Page 6: Replacement Of Switch
1-5. REPLACEMENT OF 5. Loosen the hex nuts on the adjustable foot (10), loosen belt, and MOTOR (Continued) then remove belt. 6. Remove the hinge pin from hinge (7) and remove motor (8). 7. Remove the wiring cover plate from the motor and disconnect wires from motor. - Page 7 1-7. REPLACEMENT OF ROD END BEARING To avoid electrical shock or property damage, move the power switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle. 1. Remove all equipment from top of unit. 2. Remove top (28) by lifting from unit. 3.
- Page 8 1-8. REPLACEMENT OF PUSH ROD BEARING To avoid electrical shock or property damage, move the power switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle. 1. Remove all equipment from top of unit. 2. Remove spring retainer (38) from basket holder (39). 3.
-
Page 9: Wiring Diagrams
1-10.WIRING DIAGRAMS... - Page 10 0 TO 3 YEARS: During this time, any frypot that fails due to manufacturing or workmanship issues will be replaced at no charge for parts, labor, or freight. Henny Penny will either install a new frypot at no cost or provide a new or reconditioned replacement fryer at no cost.
-
Page 11: Introduction
This section identifies and lists the replaceable parts of the Henny Penny 2-1. INTRODUCTION HB-121 Hand Breader/Sifter. Use only genuine Henny Penny parts in your unit. Using a part of lesser 2-2. GENUINE PARTS quality or substitute design may result in unit damage or personal injury. - Page 12 EXPLODED VIEW OF HB11 HAND BREADER/SIFTER...
- Page 13 HAND BREADER/SIFTER HB-11 Part No. Description Qty. √1 93856 BELT-A28 2 SC06-090 SCREW-METRIC M5X12 3 25695 WASHER 4 93800 KEY-A5X20 5 93717 PULLEY-DRIVER √6 93746 MOTOR-HB11 7 SC06-088 SCREW-METRIC M8X30 8 NS01-041 NUT -M8 LOCK LW01-004 LOCKWASHER SPLIT RING 5/16 C...
- Page 14 HAND BREADER/SIFTER HB-11 No. Part No. Description Qty. 42 SC04-003 SCREW #8-32 X 3/8 PH PHD S 43 86895 DIP BASKET √ 44 70046 SWITCH-POWER 45 15302 GUARD - SWITCH 46 22197 ON/OFF SWITCH PLATE 47 86896 DIP POT 48 86893...
Need help?
Do you have a question about the HB-11 and is the answer not in the manual?
Questions and answers