Setting The Communication Parameters For Scales; Memory Partitioning - ELCOM EURO-2500 Service Manual

Service manual Service manual Service manual Service manual Service manual Service manual Service manual Service manual
14. Set the spacing in-between receipts. Look up "Lines feed"
or enter the code 8 and press O
the number of rows that will be used as spacing in-be-
tween receipts and press O
ues are within 0–255.
KITCHEN
8.Lines feed 4
15. Set the inter-row spacing. Look up "Lines space" or enter
code 9 and press O
within 0–255 and press O
most printers this represents n/6 inches, for iDP 3421 it's
n/18 inches.
KITCHEN
9.Lines space 3
16. Enter the termination sequence that is specific for the
programmed printer. Do not include lines feed and lines
space. Look up "Termination sqn. " and press O
E
) to enter the byte sequence.
M NTER
KITCHEN
10.Termination sqn.
17. You can test your settings immediately. Look up "Test ext.
printer" using arrows or enter code 11 and press O
(N E ).The external printer prints out the character
UM NTER
set.
KITCHEN
11.Test ext.printer

5.7 Memory partitioning

5.7 Memory partitioning
These setting allow the memory partitioning for individual
tables. The set value specifies the maximum item count for a
table, e. g. if the PLU table memory range is set to 1,000 you
can program maximum 1,000 PLUs.
Practical example – how to set the memory range for 12,000
PLUs:
1. Look up "PLU table" in the memory ranges submenu or
enter the code 1 and press O
ber after the text is the current setting.
940.Memory ranges
1.PLU table 1,000
2. Set the desired memory range value (12,000) for given
table using the keyboard and press O
68
E (N E
K NTER UM
E (N E
K NTER UM NTER
|
E (N E ). Enter the value
K NTER UM NTER
E E
(N ). Note: for
K NTER UM NTER
|
K
|
|
E (N E
K NTER UM NTER
|
E (N
K NTER
18. Restore the default values. Look up "Default" using arrows
). Enter or enter the code 10 and press O
NTER
ECR restores the default values for selected printer.
). Valid val-
KITCHEN
12.Default
5.6.3 Setting the communication parameters 5.6.3 Setting the communication parameters
for scales
The ECR is capable to communicate with maximum two elec-
tronic scales. Choosing the scales type automatically sets all
the communication parameters and activity settings.
1. Select the scales you want to select the type for and press
O E
K NTER
#2 connect to Port4.
E (N -
NTER U
2. Choose the scales type. The ECR sets all the param-
eters automatically. Scales types: 1 – Morcan, 2 – Martes,
3 – Macca, 4 – none (default).
1.Scales/No scales |
2.Martes
E
K NTER
3. The newly set value appears the item text.
). The num-
4. The actual change in memory partitioning to individual
tables takes place only after the "Update all" command
was issued. Select the command using arrows or enter
code 500 and press O
E ).
UM NTER
(N E ). Scales #1 connect to Port3 and scales
UM NTER
934.Scales
1.Scales/No scales
1.PLU table 1,000
940.Memory ranges
1.PLU table 12,000
E (N
K NTER UM
940.Memory ranges
500.Update all
© Elcom s. r. o.
E (N E ). The
K NTER UM NTER
<
>
12000
|
E ).
NTER
<
Euro 2500
TX