Orientation Options - C-COR Flex Max901e Equipment Manual

Figure 7.3
RF Module

Orientation Options

7
7-8 Flex Max901e 1GHz Trunk and Bridger Amplifiers
Forward
Input
15
PORT 1 REV
AMPS
O/P TP
MODULE
DANGER
HOLD DOWN
HIGH
PORT 1
VOLTAGE
FWD
PORT 1
I/P TP STATION
FWD PAD
STATION
A
FWD EQ
SLOT
B
DANGER
HIGH B
VOLTAGE
SLOT
A
STATION
REV EQ
PORT 2
STATION
REV PAD
DISTRIBUTION
PORT 2/3 FWD POWER
PORT 3
O/P TP PLUG
MODULE
DANGER
HOLD DOWN
HIGH
VOLTAGE
15
PORT 2/3 REV
AMPS
I/P TP
Tie Wrap
H.E. SWITCHING REGULATOR
POWER SUPPLY
P/N REV
SERIAL NO.
AC IN
RAW DC
Standard Configuration
3. Firmly press the replacement RF module into the housing until the back of the RF module
bottoms against the inside of the housing.
4. Use a flat blade screwdriver to start the captive module hold-down screws into the
threaded receptacles in the housing. Tighten the screws alternately to prevent stressing the
module or housing. Torque to between 25 and 27 in-lbs (2.8 and 3.1 N·m).
5. Remove the plug-in accessories from the original module and install them into the
replacement RF module.
6. Connect the power supply plug to the RF module POWER PLUG connector.
7. Perform the Forward and Return Field Tests. Refer to Forward Field Testing on page 6-4 and
Return Field Testing on page 6-5.
15
PORT 4 REV
AMPS
EQ I/P TP
FLEX MAX
O/P EQ
INTERSTAGE FM901e AMPLIFIER DANGER
HIGH
PORT 4
MODULE VOLTAGE
FWD
HOLD DOWN PORT 4
O/P TP
PAD
ALC PAD
ALC
ALC DANGER
SENSITIVITY HIGH
VOLTAGE
MAN
TRANSPONDER
PORT 5
BRIDGER
EQ/PAD
CAUTION
UNPLUG POWER SUPPLY
CONNECTOR BEFORE DISTRIBUTION
REMOVING RF MODULE
PORT 5/6 FWD
PORT 6
O/P TP
P5/P6 FWD MODULE
DANGER
PAD HOLD DOWN
HIGH
VOLTAGE
15
PORT 5/6 REV
AMPS
I/P TP
J1
B+
J2
(rotate RF module 180° if street side
Note: The standard and rotated configurations
use a 14" cable (P/N 174355-02)
I / P T P I / P T P
A M P S A M P S
P O R T 2 / 3 R E V P O R T 5 / 6 R E V
1 5 1 5
V O L T A G E V O L T A G E
H I G H H I G H
H O L D D O W N P A D H O L D D O W N
D A N G E R D A N G E R
M O D U L E P 5 / P 6 F W D M O D U L E
O / P T P P L U G O / P T P
P O R T 3 P O R T 6
P O R T 2 / 3 F W D P O W E R P O R T 5 / 6 F W D
R E M O V I N G R F M O D U L E
C O N N E C T O R B E F O R E D I S T R I B U T I O N
U N P L U G P O W E R S U P P L Y
D I S T R I B U T I O N
C A U T I O N
R E V P A D E Q / P A D
S T A T I O N B R I D G E R
P O R T 2 P O R T 5
R E V E Q
S T A T I O N
T R A N S P O N D E R
M A N
A
S L O T
V O L T A G E V O L T A G E
H I G H B S E N S I T I V I T Y H I G H
D A N G E R A L C D A N G E R
A L C
B A L C P A D
S L O T
F W D E Q
A
S T A T I O N
P A D
F W D P A D
I / P T P S T A T I O N O / P T P
P O R T 1 H O L D D O W N P O R T 4
F W D F W D
M O D U L E
V O L T A G E P O R T 1 P O R T 4 V O L T A G E
H I G H H I G H
H O L D D O W N
D A N G E R I N T E R S T A G E F M 9 0 1 e A M P L I F I E R D A N G E R
M O D U L E O / P E Q
F L E X M A X
O / P T P E Q I / P T P
A M P S A M P S
P O R T 1 R E V P O R T 4 R E V
1 5 1 5
J1
H.E. SWITCHING REGULATOR
POWER SUPPLY
P/N REV
B+
SERIAL NO.
AC IN
RAW DC
J2
Rotated Configuration
access is required)
Forward
Input
1502154 Rev D