Beretta EXCLUSIVE C Series Installer And User Manual page 26

EXCLUSIVE
- setting TIME & DATE
TIME & DATE
ENTER TIME AND DATE
ENTER TIME AND DATE
12
18 / 11 / 2013
USE THE ARROWS TO MODIFY
USE THE ARROWS TO MODIFY
- setting the operating mode of the REC10:
MASTER: select this option when the REC10 is also a MACHINE
INTERFACE.
- configuration selection:
FROM AKM: to reset the current boiler configuration on REC10 MASTER
and finish the operation
NEW: to set a new system configuration restoring the factory setting of
the parameters
OF CONFIGURATION
Whenever a "NEW" configuration is selected, proceed as follows:
- select REC10 functionality:
ON BOARD: if the REC10 is used only as a system interface and not as
an ambient regulator
AMBIENT: if the REC10 is used as a system interface and also as an
ambient regulator of the zone where it is installed
WHERE IS THE REC10 INSTALLED?
THE REC10 INSTALLED?
- select the type of boiler INSTANTANEOUS (the boiler is the combined
variety)
INSTANTANEOUS
INSTANTANEOUS
STORAGE TANK
SELECT THE PLANT
SELECT THE PLANT CONFIGURATION
- select FLOW SWITCH.
FLUX SWITCH FLUX SWITCH
26
TIME & DATE
: 17
SELECT THE TYPE OF
SELECT THE TYPE
CONFIGURATION
FROM AKM
FROM AKM
NEW NEW
BOILER BOILER
WHERE IS
ON BOARD
ON BOARD
AMBIENT
AMBIENT
PLANT
PLANT
CH ONLY
CH ONLY
HW TANK
CONFIGURATION
PLANT
PLANT PLANT PLANT PLANT
FLOW SWITCH
FLOW METER
FLUX METER FLUX METER
- Once the guided procedure has finished, the REC10 will go to the initial
screen.
Continue with the configuration as follows:
- access the technical parameters as explained in the section "4.1 Access
to the technical parameters" , using the password SERVICE
- select PARAMETERS with the "up" and "down" keys, confirming the
selection
- next change the following parameters:
AUTO WATER FILL ENABLE: set to 1.
Then proceed with the reprogramming of the boiler, carrying out the
operations described in the section "5.2 Programming the boiler" .
5.21 Replacing the REC10 MASTER
b
The system's configuration operations need to be carried out by
professionally qualified personnel of the Technical Assistance Centre.
When replacing the REC10 MASTER, at the subsequent restart it displays
an initial screen with the firmware revision.
Pressing "ok" starts a guided procedure for configuring the system, see
section "5.20 System configuration" . Follow the procedure and carry out the
FROM AKM type of configuration.
MULTI ZONE CONTROLLER
REC10 V01.26
PRESS ANY KEY TO
PRESS ANY KEY
OF CONFIGURATION
5.22 Replacing the AKM01 board
The configuration operations should be carried out by professionally qualified
personnel of the Technical Assistance Centre. The systems continually
carries out a consistency control between the saved configuration data on
the AKM01 electronic board and those saved in the REC10; therefore, when
replacing the AKM01 electronic board, it can happen that the system detects
an inconsistency between the data saved on the AKM01 and that in the
REC10. In this case, the latter will ask the user which of the two configurations
is to be considered valid; selecting to recuperate the configuration from the
REC10 itself it is possible to avoid reconfiguring the machine:
- select REC10 with the "up" and "down" keys, confirming the selection.
SELECT THE TYPE OF
OF CONFIGURATION
5.23 Parameters combustion check
Although the parameters referring to the new combustion control
system ACC (Activate Combustion Control) are preset in the factory, the
simultaneous replacement of both electronics boards (AKM and REC 10
MASTER) could make necessary to re-programming these parameters.
- Access the technical parameters as explained in the section "4.1 Access
to the technical parameters" setting the password INSTALLER
- Select COMBUSTION MONITORING with the "up" and "down" keys,
confirming the selection
CONTINUE
TO CONTINUE
SELECT THE TYPE OF
SELECT THE TYPE
CONFIGURATION
FROM AKM
FROM AKM
NEW
NEW
SELECT THE TYPE
CONFIGURATION
FROM AKM
FROM AKM
REC10