Page 1
Installation and Setup Guide 020-103259-01 Cinema 2K-RGB CP2415-RGB and CP2420-RGB...
Page 2
Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose.
For complete product documentation and technical support, go to www.christiedigital.com. Product documentation For installation, setup, and user information, see the product documentation available on the Christie Digital Systems USA Inc. website. Read all instructions before using or servicing this product.
Caution! If not avoided, the following could result in minor or moderate injury. • Only Christie qualified technicians are permitted to open product enclosures. Laser safety precautions Read all safety and warning guidelines before operating the projector laser.
• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product by Christie qualified technicians or electricians before it can be connected to power. • SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning, removing components, or opening any enclosure.
Page 9
E—Represents the top view of the projector. • F—Represents the side view of the projector. The following table lists the hazard distance for the Christie projector lens with the zoom adjusted to its most hazardous position. CP2415-RGB and CP2420-RGB Projection lens...
Page 11
"No direct exposure to beam shall be permitted". • The Christie Laser Projection System Installation Checklist must be fully completed after the installation and sent to lasercompliance@christiedigital.com. A copy can remain on-site. This checklist can be found as a separate document in the accessory box with the manual.
Learn about the labels that may be used on the product. Labels on your product may be yellow or black and white. General hazards Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power. Fire and Shock Hazard To prevent fire or shock hazards, do not expose this product to rain or moisture.
Rack stand adapter plates 163-111104-XX Exhaust duct 163-112105-XX Touch panel 163-151108-XX Technical support Technical support for Christie Cinema products is available at: • Support.cinema@christiedigital.com • +1-877-334-4267 • Christie Professional Services: +1-800-550-3061 or NOC@christiedigital.com Cinema 2K-RGB Installation and Setup Guide–CP2415-RGB and CP2420-RGB 020-103259-01 Rev.
Do not install or operate the projector in an inverted position. If your site has any installation requirements other than a typical theater projection booth, contact Christie for assistance. Before lifting and positioning the projector, refer to the light intensity hazard distances.
Page 20
• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product by Christie qualified technicians or electricians before it can be connected to power. • A certified electrician must be present during installation to make sure the installation meets the local electrical code.
4. Verify the marriage ring is installed correctly and an anti-tamper alarm does not appear on the touch panel. Disposing of the product packaging Once the product has been installed and set up, Christie recommends reusing or recycling the product packaging according to your local regulations. Completing the installation checklist Complete the provided installation checklist (P/N: 020-103137-XX) and return it to Christie.
Re-doing this calibration is required if the following is replaced: • Color sensor board Christie recommends re-doing this calibration if any of the following are replaced: • Light engine •...
Page 36
When the countdown ends, take x, y, and fL measurements using the spectroradiometer. Christie recommends taking meter readings from the center of the screen to obtain accurate screen measurements. c) Under Measured Values, using the numeric keypad record the associated spectroradiometer values for x, y, and fL.
Do not install or operate the projector in an inverted position. If your site has any installation requirements other than a typical theater projection booth, contact Christie for assistance. The front-to-back tilt of the projector must not exceed 15° in a downward direction or 5° in an upward direction.
2. If the keystone effect is severe, unevenly adjust the feet to compensate for projector tilt. Christie recommends using the lens offset to align the center of the image to the center of the screen before correcting the keystone effect.
Adjusting the integrator rod and fold mirror Extreme misalignment of projection optics can cause permanent damage to critical optical components. Only Christie qualified technicians can perform internal optical adjustments. Notice. If not avoided, the following could result in property damage.
For the best stability, Christie recommends setting convergence while rotating the knobs in a clockwise direction. This may require first adjusting convergence by turning the knobs counter- clockwise and finalizing the convergence with a clockwise approach.