Chrysler Dodge Caravan 2002 Manual page 2027

23 - 44 EXTERIOR
BODY SIDE MOLDINGS
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 45
COWL GRILLE
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 50
EXTERIOR NAME PLATES - TAPE ATTACHED
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 51
EXTERIOR NAME PLATES - ADHESIVE
ATTACHED
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 51
FRONT FENDER
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 51
FUEL FILL DOOR
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 52
FUEL FILL DOOR BLOCKER LATCH
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 52
FUEL FILL DOOR BLOCKER LATCH STRIKER
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 53
FUEL FILL DOOR BLOCKER LOCKOUT LINK
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
BODY SIDE MOLDINGS
REMOVAL
Refer to (Fig. 1), (Fig. 2), (Fig. 3), (Fig. 4) or (Fig.
5)for proper location of fasteners holding the molding
to the wheelhouse lip and rocker panels.
(1) Warm the affected stick on molding and body
metal to approximately 38° C (100° F) using a suit-
able heat lamp or heat gun.
EXTERIOR
TABLE OF CONTENTS
page
INSTALLATION
GRILLE OPENING REINFORCEMENT
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
INSTALLATION
FRONT WHEELHOUSE SPLASH SHIELD
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
INSTALLATION
LUGGAGE RACK RISER
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
INSTALLATION
LUGGAGE RACK CROSSBAR
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
INSTALLATION
REAR QUARTER PANEL/FENDER AIR
EXHAUSTER
DESCRIPTION
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
INSTALLATION
ROOF JOINT MOLDING
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
INSTALLATION
SIDE VIEW MIRROR
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
INSTALLATION
SIDE VIEW MIRROR GLASS
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
INSTALLATION
(2) If equipped, remove pop rivets holding molding
edge to wheelhouse lip.
(3) Pull stick on molding from painted surface.
(4) Remove adhesive tape residue from painted
surface of vehicle. Use a 3M Scotch-Brite™ Molding
Adhesive and Stripe Removal Disc, or equivalent, to
clean adhesive residue from painted surfaces. These
products are available from automotive paint suppli-
ers. Refer to instructions supplied with the specific
product for proper usage.
. . . . . . . . . . . . . . . . . . . . . . . . . 54
. . . . . . . . . . . . . . . . . . . . . . . . . 54
. . . . . . . . . . . . . . . . . . . . . . . . . 55
. . . . . . . . . . . . . . . . . . . . . . . . . 56
. . . . . . . . . . . . . . . . . . . . . . . . . 57
. . . . . . . . . . . . . . . . . . . . . . . . . 57
. . . . . . . . . . . . . . . . . . . . . . . . . 58
. . . . . . . . . . . . . . . . . . . . . . . . . 58
. . . . . . . . . . . . . . . . . . . . . . . . . 58
. . . . . . . . . . . . . . . . . . . . . . . . . 59
RS
page