(2)How to use the alarm
・The way of using the alarm is the same for every alarm channel.
Example: Selecting alarm 1 and setting the alarm time to "6:30 a.m."
① P ress Button Ⓔ to show the "ALM1."
L ong press Button Ⓑ to show the alarm time setting mode. The hour starts fl ashing.
② W
ith each press of Button Ⓒ
, the hour and minute fl ash alternately. Press Button Ⓒ
to select the item to be adjusted.
3
③ W
ith each press of Button Ⓔ
, the fl ashing value increases one by one, and with each
press of Button Ⓕ
, the fl ashing value decreases one by one.
※ Long press Button Ⓔ or Button Ⓕ to quickly increase or decrease the value.
④ A fter all adjustments are completed, press Button Ⓑ to exit the alarm time setting mode.
Even if Button Ⓑ is not pressed, the display automatically returns to the time/calendar
mode within 2 to 3 minutes.
※ When the watch exits the alarm time setting display, the alarm is automatically engaged (ON).
Ⓒ
(hour: 6:00 a.m.)
122
How to use the altimeter (ALTI) mode
The current altitude and climbing speed are measured and displayed.
The current altitude and climbing speed are measured every 10 seconds and the measurement
stops when 12 hours have elapsed. When Button Ⓕ is pressed, re-measurement can be made.
Maximum 10 times of mountaineering data, of which one time is 24 hours, such as average climbing
speed can be recorded.
【CAUTION】 I f watch temperature changes when altitude is measured, some errors
may occur in measurement. Make measurements in a state not aff ect-
4
ed by temperature change such as wearing the watch on your arm.
【Caution】 W hen water runs directly from a faucet onto the watch, very high water pressure is ap-
plied. The measurement accuracy of the sensor to measure pressure temporarily de-
grades, and the values of altitude and atmospheric pressure may fl uctuate. If very high
water pressure is applied to the body of the watch, wait for about 10 minutes or more un-
til the measurement accuracy of the pressure sensor recovers and then measure again.
【Caution】 P lease avoid getting water dripped directly on the watch by wearing a raincoat when you use the watch in the rain.
Please stop recording about 10 minutes until the sensor accuracy recovers if water drips onto the watch in case of
a sudden downpour.
The altimeter is based on the barometer which might be incorrect because of the sensor getting splashed with
water such as rain.
124
Ⓒ
Ⓒ
Ⓔ
Ⓔ
Ⓕ
Ⓕ
(minute: 30 minutes)
(3)Engagement and disengagement of the alarm
・In the alarm mode, press Button Ⓕ to engage (on) or disengage (--) the alarm.
※ When any alarm of the three channels is engaged, the alarm mark
※ When the alarm is engaged, the alarm mark
(4)How to stop the alarm while it is sounding
・The alarm sounds for approximately 10 seconds at the designated time.
・Press any button to stop the alarm while it is sounding.
※ Doing this can stop the alarm regardless of the mode.
(Hourly time signal sounds.)
Alarm is engaged (ON).
Ⓕ
Alarm mark appears.
【CAUTION】 T he alarm sounds when the time in the time/calendar mode reaches the
designated alarm time.
(1)Buttons and functions
・ P ress Button Ⓐ to switch to the ALTI mode. After "ALTI" appears at the top row of the
display, the climbing speed at the top row and the current altitude at the middle row are
shown.
Button Ⓐ:To switch to the barometer/thermometer mode
Button Ⓑ
Button Ⓒ
Button Ⓓ
Button Ⓒ:To switch to the watch function
Button Ⓓ:To turn on the built-in illuminating light
Button Ⓑ
Button Ⓔ
Button Ⓓ(Press and hold) :To switch to the
Button Ⓔ: (during data recording) To switch to the
Button Ⓐ
Button Ⓕ
Button Ⓕ:To remeasure/To turn on or off the data
Button Ⓕ(Press and hold) : Mountaineering record start/end
(2)Explanation of display
Climbing speed: the indication is updated every 10 seconds.
Range of display: between -9999 and 9999 m/h, between -9999 and 9999 ft./h
Altitude: the indication is updated every 10 seconds.
Range of display: between -699 and 9164m, between -2290 and 30065 ft.
Current time: current time is displayed
※The units used in the illustration are the default settings.
appears on the display.
appears on the display regardless of the mode.
(Hourly time signal does not sound.)
Alarm is disengaged (OFF).
Ⓕ
Alarm mark does not appear.
(Press and hold) :To switch to the altitude
correction mode
Bluetooth mode
display of recording data/Plus modification
recording/Minus modification
3
123
4
125